DTM Print Primera AP550e User manual
LABELAPPLICATOR
Mode
Recall/
Reset
+-
Mode Recall/
Reset +-Mode Recall/
Reset +-
Mode Recall/
Reset +-Mode Recall/
Reset +-
LABELAPPLICATOR
Mode
Recall/
Reset
+-
Mode
Recall/
Reset +-Mode Recall/
Reset +-Mode Recall/
Reset +-
LABELAPPLICATOR
Mode
Recall/
Reset
+-
Mode Recall/
Reset +-Mode Recall/
Reset +-Mode Recall/
Reset +-
LABELAPPLICATOR
Mode
Recall/
Reset
+-
LABELAPPLICATOR
Mode
Recall/
Reset
+-
Free Technical Support!
Contact our DTM Print support team
phone at +49 611 92777-0 or use the
online live chat on our webpage
dtm-print.eu. This service is free for all
our customers.
AUnpack and Setup
1. Remove the AP550e from its
packaging.
2. Remove all items from the supply box.
3. Place the unit toward the back of a
table with a depth of 76 cm or more.
4. Connect the power and switch on the
AP550e.
Power CordPower Adapter
76 cm or more
Power Switch
Power Input (12v)
CLabel/Container Settings (for die-cut labels)
19. Start Labeling
15. Access Label/Container Settings
16. Sensor Calibration
17. Platform Position
18. Guide Position
Press “Mode” once. When “F 0” is displayed hold“Mode” for
2 seconds to access Label/Container
Settings.
Press “Recall/
Reset” twice.
Push down on arm until“0.00”is
displayed.
“SC-” is displayed.
Push here
Press “Recall/
Reset” twice.
“PPo” is displayed. Load the container. Press and hold “+” or “-” to move
the platform to the desired label-
ing position.
Press “Recall/ Reset”
once.
“gPo” is displayed. Container
Guide
Loosen the Thumb Screw
under the platform to adjust
the guide
side-to-side.
Thumb Screw
under platform
Press “Mode” to
store settings.
Lower the Application Arm quickly until it touches
the container.
The platform will move toward you.
Maintain downward force on the arm until the
label is completely applied.
Push here
15a 15b
16a 16b 16c
17a 17b 17c 17d
18a 18b 18c 18d
074392-190225
Primera AP550e Quickstart
AP550
LABEL APPLICATOR
Mode Recall
Reset
+-
Liner Drive Roller
Label Guide Roller
Application Rolle
r
Peel Edge
Liner Idler Roller
Label Path
10. Align the leading edge of the label
stock with the roll as shown.
11. Make sure the labels will be fed under
the Sensor Location Line.
12. Move the Guide Collars so they are
close to, but not pinching the label
stock.
13. Lock the labels in place by pushing up
on the metal Liner Idler Roller. Make
sure there are no labels past the Liner
Drive Roller.
14. Move the Application Arm to the appropriate height by squeezing
the Pin Release Bar and pulling up on the arm.
Distance from
label stock to arm
side plate should
be equal in these
locations.
Sensor Location Line
Guide Collars
Align Here
Unlock
Lock
Liner Idler Roller
Liner Drive Roller
Position Container Height
Notch 4 15-20 cm
Notch 3 10-15 cm
Notch 2 5-10 cm
Notch 1 0-5 cm
Pin Release Bar
Pin
no labels here
BLoad Label Stock
5. Place the label roll on the Roll Bar as shown. For narrow rolls you may have to ip guides so
the “L”faces away from the roll on each side.
6. Place the Roll Drag Arm under the Roll Bar so that the rounded tip is near the center of the roll.
7. Place the Roll Bar with labels on the pins so that the bar is fully seated on the pins.
8. Remove approximately 38 cm of labels from the liner.
labels facing up holes to the rear
Roll Bar
Roll Guides
Roll Drag Arm
38 cm
9. Load the label stock according to the diagram below:
Label Path
Liner Drive Roller
Label Guide Roller
Liner Idler Roller Application Roller
Peel Edge
