DTM System BLINK 868 User manual

GENERALINFORMATION
Device designed for installation in all types of vehicles. Using existing electrical circuits (eg. Traffic lights) allows
radiocontrolofdevices.
Method of use depends on individual needs and creativity of a user. BLINK 868 transmitter can also be integrated
withany alarmsystems, gate automation and smart home systems fitted with DTMreceiver.
Transmitter can be connected directly to executive element in the system, such as low voltage bulb, acoustic signaler, etc.
Waterproofcase allows installation at any selected location. Metal handle guarantees solid mounting.
TECHNICALSPECIFICATIONS
4input(control) 6...30VDC
4numberof channels 4
4frequency 868MHz
4maximumrange do 200m
4effectiveradiated power, EIRP do 10mW
4rollingcode system 104-bit IRS
4workingtemperature -20°C/ +55°C
4IPprotection IP-66
4dimensionwithout /with handle 31x31x42mm/ 31x31x62mm
4weight 40g
4part of the system DTM868MHz
installation and operating manual v.1.2
TRANSMITTER
BLINK 868
Fig.1. Transmitter view.
GND (0V)
input
(control)
+6...30VDC red wire
black wire
mounting hole
Ø6,5mm
LED indicating radio transmitter work

1.Transmitterinstalation
For safe installation BLINK 868 transmitter should be protected with delayed tripping time fuse of 500mA
value(eg.ZKT-0.5A). Fuse and slot are not included.
Controlsignal fromthe automationmust beconnected to two BLINK wires (red wire +6...30VDC, black 0V)
Exampleof electrical diagram with BLINK 868 connection is shown on Fig.2.
2.Transmitteruse
Number of pulses equals number of channel. Eg. three pulses corresponds to the standard remote third
button.Acceptedprinciple illustrated on Fig. 3.
After each pulse transmitter waits for a while for any further pulses. Followed by a radio signal transmission.
Continoustransmission canbe obtainedby lengtheninglast pulse.Illustrated in Fig.3.
Eachtransmitter activationis signaledby LED located on the transmitter (see Fig.1).
For comfortable registering transmitter to receiver disconnect transmitter from installation and use
battery, accumulatoror other voltage source.
Fig.2. Example of BLINK 868 electrical connection to bulb circuit.
2
1
3
M e t h o d o f c l a m
gel-connector on BLINK
wire and circuit wire
existing installation,
external wire max 2mm
Wire with female
connector BLINK 868
6...30V DC
+-
momentary
button transmitter
BLINK 868
bulb
red
wire
black
wire
delay fuse
0,5A

Fig.3. Assignment of exemplary remote buttons to BLINK pulses combination.
hone short pulse corresponds to short press of number 1 button
htwo short pulses corresponds to short press of number 2 button
hthree short pulses corresponds to short press of number 3 button
hfour short pulses corresponds to short press of number 4 button
34
1
2
1s
hone long pulse corresponds to holding number 1 button
hone short and one long pulse corresponds to holding number 2 button
htwo short and one long pulse corresponds to holding number 3 button
hthree short and one long pulse corresponds to holding number 4 button
max. 30s
VICTORY remote
buttons numbering

WA R R A N T Y
DTM System checks all the devices before shipping. The
warranty time is 24 months from the selling date.This time is
counted according to the warranty label. The manufacturer
will fix all the problems which come because of his fault. Non
functioning device should be delivered back to the
distributor with short problem description. The cost of
mount/dismount is covered by user. The warranty do not
cover: batteries in the remotes, faults caused by improper
usage, user self repairs and adaptations, lightning strikes,
over voltages or short circuits in the mains supply.
Appropriatelegalacts regulates detailsofthe warranty.
D I S P O S A L
The intention of the WEEE Directive (Directive
2002/96/EC on waste electrical and electronic
equipment) is to reduce the amount of
hazardous substances in waste. The underlying
purpose is to promote the avoidance, recovery
and risk-free disposal of waste.
DTM System hereby declares that the radio
tra n s mit t e r com p l ies w i t h Di r e cti v e
2014/53/EU. The full text of the EU Declaration
of Conformity is available at the Internet
address.