DTS DTS300 User manual

Before this model has being significantly changed to another new version, the parts, appearance and the existing version can be developed and
modified that would lead to a slight difference from the original design. DTS reserve ALL the Rights of change of parts and contents WITHOUT
specified notification.
Length:510mm
Width:115mm
Height:200mm
Main Rotor Diameter: 555mm
Weight:approximately 360g(Without Battery)
Brushless Motor2086-4050
DTS300
DTS
R
Specifications
25A Brushless Motor ESC
.
Swash Servos*3(1.2kg cm,0.08s/60 )
.
Tail Servos*1(0.6kg cm,0.04s/60 )
6-Channel Transmitter
11.1V 1200mAh 25C Li-polymer Battery
GWY2013
GWY 6TL V2 2.4GHz
3-axis Gyro

Statement
Main Frame and Tail Boom Assemble Procedure
Tail Rotor Assemble Procedure
Power System Assemble Procedure
Parts List
Check of package's parts and accessories
Electronic Parts and Connection Procedure
Pre-Flight Controls Test
Flight Operation Procedure
Main Blade Adjustment
Tail Drive Belt Adjustment
Tail Drive Servo Adjustment
Main Rotor Head and Gears Assemble Procedure
Exploded View
2
3
4
8
9
9
10
1
Foreword
Thank you for choosing DTS's product. For better understand usage of DTS300 helicopter,
please read this manual carefully before installation and operation. This can ensure proper usage
and safe operation! For your convenience of adjustment, maintenance and other operation, please
keep this manual in a proper manner.
For further information, please visit our website: www.zondahobby.com
Table of Contents
11
12
13
14
16
7

An RCHelicopter is nota toy! For avoiding accidentsand damage, pleaseoperate the helicopterproperly.
Since the consumerhave purchased thehelicopter, theyshould take allthe risks in the usage.To ensure
your safety, if you are a beginner, you are recommended to consult or get assistance from experienced RC
modelers or yourlocal hobby stores.
Youshould buy theauthorized DTS accessorieswhen you choosingthe accessories. Otherwise, some
RC functions may not be matched or function unproperly.
Please keep instruction manual to properly maintain your model.
RC helicopter is controlled by radio signals. It may be interfered by other radio signals during operation.
These interference may cause the helicopter lose control.
1.An RC Model is not a toy! Improper operation or misuse may lead to serious damage or loss. It is
prohibited for childrenunder 14 yearsto operate thisproduct.
2.Keep it awayfrom high temperatureenvironment and corrosivechemicals for storageand flight.
(the operation temperature: from:-10 to 50 )
3.If you are not an experienced pilot or have not flown this type of model before, we recommend that
you get assistance of an experienced pilot for your first flights. Please avoid flying with other RC models
with same frequency.
4.Please choose aopen flight areaand use thetraining gear setfor your firstfight in orderto minimize
your loss dueto control mistakes.
1.To avoid the loss of the property of others, please keep away from high tension power lines, high
buildings or any other obstacles while flying
2.Keep away fromcrowds in caseof accidents
3.Do NOT operate in rain,thunder, storms,lighting, strong windor any otherbad weathers toensure
,
your and thehelicopter s safety
4.Please avoid using in a bathroom or a rainy day to prevent moisture or water vapor from entering the
helicopter inside whichmay lead mechanicalor electronic componentsmalfunction and causeunex-
pected accidents
5.Do Not re-equip, upgrade or repair your helicopter with the accessories outside the DTS parts catalog
in order to ensure the safety of the model structure!
6.Keep people andobjects away fromthe spinning unitand parts incase of damageor injury!
1.Please make surethe helicopter frequencywill not interferedwith others beforeevery flight.
2.You should confirm the batteries of your transmitter and helicopter are fully charged before every flight
and your firstflight.
3.Both the throttle stick (left-hand stick) andthrottle trim MUST be in their lowestposition before every
flight. Each time before your flight, you must ALWAYS turn on the transmitter power first before con-
necting the flight battery to the receiver. After your flight, you should disconnect the flight battery from
the receiver before turn off the transmitter.
4.Please make sure that every servos function properly with correct directions after powering on.
5.Make sure every connection of pushrods is proper and the helicopter battery placed in fixed position.
Statement
Warning Label Legend
Do not attemptunder any circumstances.
Mishandling due tofailure to followthese instructions mayresult in danageor injury.
Mishandling due to failure to follow these instructions may result in danger.
CAUTION
WARNING
FORBIDDEN
Safety Precautions and Warning
Pre-flight check
1
WARNING
FORBIDDEN

2
Check of package's parts and accessories
Please check the parts and accessories in the package. In the event of defective or missing parts, please contact the
retailer for help.
1
7
346
5
1
1
1
1
1
1
1
1.
2.6TL
3.
4.
5.
6.
7.
RC Helicopter
2.4GHz 6-Channel Transmitter
2S & 3S Batery Charger
SD Card
11.1 V, 1200 mAh Li-Po Battery
Tool Pack
Battery Bandage
2
Package Box Content RTF WOB RFR RFR with AH6 Radio System
DTS 300
6TL - 2.4GHz 6-Channel Transmitter
AH6T - 2.4GHz 6-Channel Transmitter
GWY2013 - Receiver & Gyro
G02 - Gyro
AH6R - Receiver
2S & 3S Battery Charger
Li-Po Battery :1200mAh 3S1P 11.1V Ec3
Battery Bandage
SD Card - Manual
ToolPack

Electronic Parts and Connection Procedure
3
Receiver Connection Procedure
Aux 02
Pitch Servo Plug
Aux 01
Gyro Gain Signal Plug
Brushless ESC Plug
Aileron Servo Plug
Elevator Servo Plug
Gyro Rudder Plug
Power Supply Plug
Brushless Motor
Li-Po Battery
Rudder Servo
Brushless ESC
Elevator Servo
Aileron Servo
Pitch Servo
Receiver 3-axis Gyro

Push up the throttle stick slowly until the motor rotate. Make sure that the motor rotates clockwisely and the main
blade rotates anti-clockwisely.
Throttle Position: LeftThrottle Position: Right
4
Pre-Flight Controls Test
1.Control Test: Throttle
Please don't pushthe throttle stickupward over 1/5.The motor will spins athigh velocity ifthe throttle stickis
over pushed. This may cause damage on the product or self injury. Besides flight operation, when performing
maintenance or adjustment and fine-tuning indoor, please remove the connection between the motor and the
ESC. This can prevent themotor from unpredictablespinning and causeacidents.
Swashplate's Back and
Front end movement
2.Control Test: Elevator
Throttle Position: Right Throttle Position: Left

5
3.Control Test: Pitch (only aerobatics use)
Swashplate's upward and
downward movement
4.Control Test: Aileron
Swashplate's Left and Right declining movement (The rudder's control is the same in both
left and right-hand throttle transmitter)
Rear View
Throttle Position: Right Throttle Position: Left
Rear View Rear View

6
5.Control Test: Rudder
Tail rotor blades pitch change (The rudder's control is the same in both
left and right-hand throttle transmitter)
6.Gyro adjustment
Disconnect the connection between ESC and motor, turn on the power of the transmitter and helicopter,
move the pushrod to check the sercos direction.
1. Hold the helicopter rotates around the main shaft, gyro will control the tail servo to compensate the
movement of the rotation direction.
E.g. When helicopter tail rotates rightward, the gyro will control the tail servo to rotates the tail leftward.
(Picture A)
2. Hold the helicopter and tilt the fuselage to a certain direction, the swashplate will be tilted toward the
opposite direction of the fuselage.
E.g. When the helicopter tilted forward, the swashplate will be tilted backwards. When the helicopter tilted
backward, the swashplatewill be tiltedfoward. (Picture B)
If the helicopter tilt laterally, the swashplate will be corrected in the opposite direction. (PictureC)
When the fuselage return to the initial horizontal position, the swashplate will also return to the initial position.
Picture A Picture B
Picture C
Tail Rotate Direction
Fuselage direction
Swashplate
direction
Swashplate
direction
Fuselage
direction
Fuselage
direction
Swashplate
direction
Swashplate
direction

7
1
2
Mode1
Mode2
4
3
1
3
2.End-flight procedure
Disconnect the helicopter's
electricity
Switch off the transmitter Takeout the battery
Flight Operation Procedure
1.Take Off Procedure
Insert the batteryto the batterynotch Fix the battery's position with the bandage
Adjust the antenna to the shown position. Pull the
throttle to the most downward position then switch
on the transmitter.
Connect helicopter's electricity

2
34
1
Main Blade Adjustment
1
DTS 300
Blade tracking is an important step to affect the flight performance. Main rotor blades that are out of track may cause vibration and
instability. Although the main rotor blades of each models are tracked at the factory, minor adjustment to blade tracking
may be required after blade changes. Thus one of the main blades pasted a coloured tracking tape to identify which blade is running
low or high in the blade tracking process.
Caution: Be sure to maintain a safe distance from the helicopter (3~5meter) when tracking the main rotor blades.
Coloured tracking tape
(From the topto the bottom)
Adjusting Pushrod When 2 mainblades stay onthe same rotatingrail,
the main bladeadjustment is completed.
2 After confirming which blade is running low and high, switch off the helicopter power supply before making any necessary
adjustments to the linkage. You can increase the pitch of the low blade by shortening the mixing arm to inner swashplate linkage.
This is achievable by turning one of the Ball Link ends in by one-half to one full turn at a time. Or, you can decrease the pitch of the
high blade by lengthening the same linkage.
3Remark: The blade you choose to raise or lower when making tracking adjustments will depend on the pitch of each blade. Open the
3D aerobatics (the tail motor power supply wire should be cut off) and the throttle/ collective stick in the middle position, both rotor
blades should be close to 0 degrees. You can easily identify which rotor blade to adjust. If one blade is lower than 0 degree, raise
it to match the other blade. If one blade is higher than 0 degree, lower it to match the other blade.
4 Generally, there is not much adjustment should be necessary to properly track the main rotor blades. If significant adjustments are
required, be sure to double-check the length of both mixing arm to inner swashplate linkages. You should also check the blades for
any damaged or twists. In fact, you should be able to get both blades tracking perfectly in the same helicopter. However, the small
defects in the ball links and threaded linkage rods/ pushrods may not always be possible to affect the blade tracking. Don't worry, the
helicopter should be able to have a good flying performance even the blade tracking is adjusted as close as possible.
Coloured tracking tape
8

Tail Drive Servo Adjustment
As this model is a precise craft, unexpected self-rotation during flight could because of several reasons.
Could adjust throughfollowing procedure: (disconnectthe motor andthe ESC canavoid unexpected accidents)
First switch onthe transmitter.Then connect the helicopter withelectricity, and tilt therudder stick andtrim to
the middle position(Figure 1); Keepthe tail driveservo boom mountand the tailboom perpendicular (Figure2).
Adjust the position of the tail drive servo and keep the distance between the Tail Pitch Control Slider Ring and
the tail case (approximately 1/3 of the spindle) (Figure 3). Keep the servo and the servo arm perpendicular
(Figure 4).
Rudder position:
Middle
Figure 1
Figure 3 Figure 4
Figure 2
Loosen Belt is one of the reason for tail-lock fail besides gyro setting. Adjust by following the above:
Loosen the screws that mounting the tail boom to the main frame, then pull the tail boom backward. Pay
attention to the belt's elasticity. Fasten the screws back when the belt is adjusted.
Tail Drive Belt Adjustment
Throttle Position: Right
9

10
Main Rotor Head and Gears Assemble Procedure
Bearing
( 4mm* 10mm*3mm)x3
Nylon insert lock nut
( 2mm*2.8mm)x2
Retaining Collar
( 4mm* 8mm*4.3mm)x1
Set Screw
(M3* 3mm)x1
Hexagon Socket Head Bolt
(M2*10)x1
Hexagon Socket Head Bolt
(M2*12)x3
Linkage Ball
(S 4mm*7.5mm*L2.5mm)
Already assembled
Linkage Ball
(S 4.0*6.1mm*L2.5mm)
Already assembled
Washer Head Phillips Screw
(M2*4mm)
Already assembled
Linkage Ball
(S 4mm*6.1mm*L2.5mm)
Already assembled
Swash Plate
Already assembled
Linkage Ball
(S 4.0*7.5*L2.5mm)
Already assembled
Anti-rotation Pin
( 2mm*14mm*M2)
Already assembled
Flange Bearing
(2.5mm* 2mm* 5mm)
Already assembled
Control Arm Linkage
Already assembled
Control Arm Bushing
( 2.5* 1.5*4mm)
Already assembled
Spindle
( 1.5mm*8.5mm)
Already assembled
Hiller Control Arm
(20.5mm* 5mm) Flange Bearing
(2.5mm* 2mm* 5mm)
Already assembled
Control Arm Bushing
( 3mm* 4.5mm*1.3mm)x2
Washer
(0.10mm* 5mm * 8mm)x2
O-ring
( 2.9mm* 6mm*3mm)x2
Bearing
(2.5mm* 3mm * 6mm)x4
Washer
(0.1mm* 3.1mm* 5.6mm)x2
Washer
(0.5mm* 2mm * 5mm)x2
Step washer
(0.55mm* 3mm * 5.5mm)x2
Hexagon Socket Head Screw
(M2*6mm)x2
Thrust Bearing
(3.5mm* 3mm * 8mm)x2
Main Shaft
( 3mm*38.2mm*M2)x1
Blade Grip Smaller inner
diameter
Greater inner
diameter
Paste necessary lubricant
on the thrust bearing
Pay attention to the
install-position of the
Blade Grip
Paste Lubricant
CAUTION
Proper torque is fine when locking a screw into
plastic parts,redundant torque may lead to
screw strip or fracture.
Please confirm that the screw is fastened
tightly before use.
Apply a little amount of T43 thread lock
when fixing a metal part.
Metallic Pushrod
(M1.6*24mm)x2
Pushrod Linkage x4
Anti-rotation Pin
( 2mm*14mm*M2)x1
Linkage Ball
(S 4mm*7.5mm*L2.5mm)x7
Control Arm Bushing
( 3mm* 4.5mm*1.3mm)
Step washer
( 2mm* 3.8mm*0.4mm)x2
Flange Bearing
(2.5mm* 2mm* 5mm)x4
Control Arm Bushing
( 2.5* 1.5*4mm)x2
Hiller Control Arm
(20.5mm* 5mm)x2
Spindle
( 1.5mm*8.5mm)x2
Main Shaft
( 3mm*38.2mm*M2)
Main Rotor Head
O-ring
( 2.9mm* 6mm*3mm)
Hexagon Socket Head Screw
(M2*6mm)
Washer
(0.5mm* 2mm * 5mm)
Bearing
(2.5mm* 3mm * 6mm)
Blade Grip
Step washer
(0.55mm* 3mm * 5.5mm)
Thrust Bearing
(3.5mm* 3mm * 8mm)
Washer
(0.10mm* 5mm * 8mm)
Washer
(0.1mm* 3.1mm* 5.6mm)
Washer Head Phillips Screw
(M2*4mm)x3
20mm
12
8.1mm
38.0mm
Main Shaft
( 4mm*110mm)
Set Screw
(M3* 3mm)
Hexagon Socket Head Bolt
(M2*12)
Nylon insert lock nut
( 2mm*2.8mm)
Bearing
( 4mm* 10mm*3mm)
Bearing
( 4mm* 10mm*3mm)
Retaining Collar
( 4mm* 8mm*4.3mm)
Step washer
( 2mm* 3.8mm*0.4mm)
Hexagon Socket Head Bolt
(M2*12)
Hexagon Socket Head Bolt
(M2*10)
Nylon insert lock nut
( 2mm*2.8mm)
Main Gear
Main Tail Drive Gear Cap
Main Tail Drive Gear
Flat Head Phillips Screw
(M2*5.0mm)
Flat Head Phillips Screw
(M2*5.0mm)x3
Push Rodx2
(S 4mm*7.5 mm* L2.5 mm)
(S 4mm*6.1 mm* L2.5mm)
Linkage Ball
Linkage Ball

11
Main Frame and Tail Boom Assemble Procedure
Set Screw
(M3* 3mm)x1
Pinion Gear
(10Z)x1
Hexagon Pan Head Screw
(M3*8mm)x2
Hexagon Pan Head Screw
(M3*10mm)x4
Washer
( 3mm* 7mm*0.8mm)x6
Nylon insert lock nut
( 2mm*2.8mm)x4
Flat Fillister Head Phillips Screw
(M1.7*6mm)x1
Hexagon Socket Head Screw
(M2*12mm)x6
Flat Fillister Head Phillips Screw
(M1.7*9mm)x9
CAUTION
Proper torque is fine when locking a screw into
plastic parts,redundant torque may lead to
screw strip or fracture.
Please confirm that the screw is fastened
tightly before use.
Apply a little amount of T43 thread lock
when fixing a metal part.
Hexagon Socket Head Screw
(M2*8mm)x2
Do not twist the belt
and the pulley
Main Frame, Left
Main Frame Right
Stabilizer
Notify difference
of bearings and
insert in the slot
Tail Drive Belt
(2.5mm*R360MXL)
Nylon insert lock nut
( 2mm*2.8mm)
Washer head Phillips screw
(M1.7*4mm)
Flat Fillister Head Phillips Screw
(M1.7*6mm)
Flat Fillister Head Phillips Screw
(M1.7*9mm)
Hexagon Pan Head Screw
(M3*10mm)
Washer
( 3mm* 7mm*0.8mm)
Washer
( 3mm* 7mm*0.8mm)
Hexagon Pan Head Screw
(M3*10mm)
Set Screw
(M3* 3mm)
Pinion Gear
(10Z)
Hexagon Pan Head Screw
(M3*8mm)
Washer
( 3mm* 7mm*0.8mm)
Hexagon Socket Head Screw
(M2*12mm)
Tail Drive Belt Pulley Base
Bearing
(2.5mm* 2mm* 5mm)
Already assembled
Tail Drive Belt Pulley
(8.2mm* 4.3mm)
Hexagon Socket Head Screw
(M2*8mm)
Hexagon Socket Head Screw
(M2*6mm)x2
Flat Fillister Head Phillips Screw
(M1.4*5mm)
Tail Servo Pushrod Guide x2
Tail Servo Boom Mount x2
Tail Boom
( 10mm*287mm)
Servo arm B
Tighten the mount after insertion.
Match the slot of tail servo boom mount to
the notch of the tail boom
Notice and aim the slot of the tail boom and
the tail servo boom mount before insert
Nut
(M2* 2mm*0.4mm)
Linkage Ball
(S 4.0mm*6.5mm*2.9mm)x4
Linkage Ball
(S 4.0mm*6.5mm*2.9mm)
Bearing
(2.5mm* 2mm* 5mm)x2
Horizontal Fin
Mount
Washer head Phillips screw
(M1.7*4mm)x2
Washer head Phillips screw
(M2*8mm)
Flat Fillister Head Phillips Screw
(M1.7*4mm)
Washer head Phillips screw
(M2*6mm)
7.5g SERVOx1
Tail Pushrod
Stabilizer
Motor Mount
Motor(2086-4070)
Nut
(M2* 2mm*0.4mm)x1
Washer head Phillips screw
(M2*8mm)x4
Washer head Phillips screw
(M2*6mm)x2
Flat Fillister Head
Phillips Screw
(M1.7*4mm)x1
Flat Fillister Head
Phillips Screw
(M1.4*5mm)x2
83mm
163mm
200mm
254mm

12
Tail Rotor Assemble Procedure
Tail Drive Belt
(2.5mm*R360MXL)
Bladex2
Notice the assembling
position of the blades
Paste necessary Lubricant
Tail Case, Right
Tail Rotor Shaft
Drive Pulley Cap Tail Rotor Shaft Drive Pulley
Tail Case, Left
Bearing
( 3mm* 7mm*3mm)
Hexagon Socket Head Screw
(M2*8mm)
Hexagon Socket Head Screw
(M2*16mm)
Hexagon Socket Head Screw
(M2*12mm)
Washer head Phillips screw
(M2*6mm)
Hexagon Socket Head Bolt
(M2*12mm)
Step Washer
( 2mm* 3.8mm*0.4mm)
Nylon insert lock nut
( 2mm*2.8mm)
Hexagon Socket Head Screw
(M2*12mm)x2
Hexagon Socket Head Screw
(M2*16mm)x2
Washer head Phillips screw
(M2*6mm)x2
Nylon insert lock nut
( 2mm*2.8mm)x3
Hexagon Socket Head Screw
(M2*8mm)x1
Hexagon Socket Head Bolt
(M2*12mm)x1
Step Washer
( 2mm* 3.8mm*0.4mm)x1
Set Screw
(M3* 3mm)
Linkage Ball
(S 4mm*6.5mm*2.9mm)x1
Bearing
( 2mm* 5mm*2.5mm)x2
Brass Spacer
( 2mm* 3.5mm*1.5mm)
Already assembled
Tail Rotor Pitch Lever
Bearing
( 2mm* 5mm*2.5mm)
Already assembled
Linkage Ball
(S 4mm*6.5mm*L2.9mm)
Washer
(0.1mm* 5mm * 6mm)x4
Bearing
(2.5mm* 3mm * 6mm)x4
Linkage Ball
(S 4mm*7.5mm*L2.5mm)x2
Hexagon Socket Head Bolt
(M2*12mm)x2
Thrust Bearing
(2.5mm* 3mm * 6mm)x2
Brass Spacer
( 3mm* 4.5mm*1.6mm)x2
Brass Spacer
( 2.5mm* 2mm*3.2mm)x2
Hexagon Socket Head Bolt
(M2*10)x2
Hexagon Socket Head Bolt
(M2*10)x2
Linkage Ball
(S 4mm*7.5mm*L2.5mm)
Nylon insert lock nut
( 2mm*2.8mm)
Washer
(0.5mm* 2mm * 5mm)
Thrust Bearing
(2.5mm* 3mm * 6mm)
Washer
(0.1mm* 5mm * 6mm)
Bearing
(2.5mm* 3mm * 6mm)
Bearing
(2.5mm* 3mm * 6mm)
Brass Spacer
( 3mm* 4.5mm*1.6mm)
Hexagon Socket
Head Bolt
(M2*12mm)
Tail Blade Gripx2
Smaller inner
diameter
Greater inner
diameter
Paste necessary lubricant
on the thrust bearing
1.Check to rotate the belt 90 degrees when
assembling
2.Belt tension:Recommend to lightly tighten
the drive belt after assembling tail boom
to avoid vibration,belt friction and rotation
slip
Spindle
( 1.5mm*8mm)x2
Washer
(0.5mm* 2mm* 5mm)x4
Bearing
( 4mm* 7mm*2.5mm)x2
Brass Spacer
( 3mm* 4mm* 5.5mm*9.7mm)x1
Linkage Ball
(S 4mm*6.5mm*L2.9mm)x1
Brass Spacer
( 2mm* 3.5mm*1.5mm)x1
Tail Rotor Hub
Bearing
( 3mm* 7mm*3mm)x2
Vertical Fin
Horizontal Fin
Brass Spacer
( 2.5mm* 2mm*3.2mm)
Drive belt illustration
Back
Front
CAUTION
!
CAUTION
Proper torque is fine when locking a screw into
plastic parts,redundant torque may lead to
screw strip or fracture.
Please confirm that the screw is fastened
tightly before use.
Apply a little amount of T43 thread lock
when fixing a metal part.
( 4mm* 5mm* 0.55 mm)x1
Tail Rotor Pitch
Control Fork
Tail Rotor Pitch Control Ball Link x2
Already assembled Spindle
( 1.5mm*8mm)
Already assembled
Linkage Ball
(S 4mm*6.5mm*L2.9mm)
Already assembled
Brass Spacer
( 3mm* 4mm* 5.5mm*9.7mm)
Already assembled
Tail Rotor Pitch
Control Slider Ring
Already assembled
Bearing
( 4mm* 7mm*2.5mm)
Already assembled
Washer
( 4mm* 5mm*0.55 mm)

13
Power System Assemble Procedure
Pushrod Linkage x6
Metallic Pushrod
(M1.6*24mm)x3
Servo Arm A x3
Notice the position
Nut
(M2* 2mm*0.4mm)
Linkage Ball
(S 4.0mm*6.5mm*L2.9mm)
Flat Fillister Head
Phillips Screw
(M1.7*4mm)
Nut
(M2* 2mm*0.4mm)x3
Flat Fillister Head
Phillips Screw
(M1.7*4mm)x5
Linkage Ball
(S 4.0mm*6.5mm*2.9mm)x3
Hexagon Socket Head Screw
(M2*4mm)x1
Hexagon Socket Head Screw
(M2*12mm)x2
Hexagon Socket Head Screw
(M2*16mm)x1
Nylon insert lock nut
( 2mm*2.8mm)x4
Hexagon Socket Head Bolt
(M2*14mm)x2
Washer head Phillips screw
(M2*8mm)x4
Washer head Phillips screw
(M2*6mm)x2
Washer
( 2mm* 5mm*0.5mm)x2
7.5g SERVO x3
Tail Boom Support Rodx2
Plastic Cannula
12
20mm
38.0mm
8.1mm
CAUTION
Proper torque is fine when locking a screw into
plastic parts,redundant torque may lead to
screw strip or fracture.
Please confirm that the screw is fastened
tightly before use.
Apply a little amount of T43 thread lock
when fixing a metal part.
Washer
( 2mm* 5mm*0.5mm)
Anti-rotation Bracket
Canopy
Landing Skid Land Cap x4
Flat Fillister Head Phillips Screw
(M1.7*4mm)
Landing Skid
( 4.2mm* 5mm*155mm)x2
Landing Gear Strut x2
Washer head Phillips screw
(M2*6mm)
Washer head Phillips screw
(M2*8mm)
Pushrodx3
Double-sided Tape
ESC
11.1V 1200mAh Battery
Hook-and-Loop Band
Hexagon Socket Head Screw
(M2*12mm)
Hexagon Socket Head Screw
(M2*16mm)
Nylon insert lock nut
( 2mm*2.8mm)
Washer head Phillips screw
(M2*8mm)
Hexagon Socket Head Bolt
(M2*14mm)
Hexagon Socket Head Screw
(M2*4mm)
Nylon insert lock nut
( 2mm*2.8mm)
7.5g SERVO x3
Main Bladex2
Centre Hub Cap
ESC Tape
3-axis gyro

Exploded View
14
110
018
105
041
006
040
007
106
006
032
103
036
104
082
003
087
087
083
057
086
084
085
007
081
078
061
063
077
056
029
068
080
079
070
057
052
032
051
049
050
048
031 031
028
030
028
028
028
027
036
024
023
022
036
020
021
020
019
026
017
018
007
013
012
015 014
009
016
006
013
001
012 011
010 007
006
008
005 004 003 002
029
101
007
095
029
096
095
097
098
099
100 019
046
102
046
025
028
033
034 034
034
035
036
007
045
038 039
037
042
043
046 047
044
044
053
056
070
057
055
054
054
066
050 060
062
064
025
050
060
058
007
059
065
066
025
067
056
068
029
069
070
072
073
074
075
076
109
003
108
071
089
063
061
032
107
089
085
088
082
081
092
093
091
094
091
090
025

15
Parts List
2* 5*2.54
1
1
2
2* 3.5*1.5
1
1
1.5*82
2
2
2
2.5* 6*3
2
3* 4.4*1.6
5* 6*0.1
2
1
1
4* 7*2.52
3* 5.5*9.71
M2*8
3
1
23*180
1
M2*16
3
1
34.5*26.4*3
M3*3
1.5*8.5
2
1.5* 2.5*4
2* 3.8*0.4
M2*4
3.0* 5.5*0.55
254*28*4
2* 5*0.5
M2*6
25A
1
S 4*7.5*2.5
3
4* 8*3
11.1V 1200mAh
2
M3*10
M1.7*9
1
1
4
M1.6*38*20
4* 8*4.3
S 4*6.5*2.9
4*110
M2*10
1
5* 8*0.1
1
6
4
1
1
1
9
1
3*38.2
3.0* 4.5*1.3
2
M2*14
11
3.0* 8*3.5
2.9* 6*3
1
2
4
2
8
2
2
2
2
2
2
3
4
2
1
036
040
039
038
037
045
046
047
048
044
043
042
041
053
054
055
052
051
050
049
2
3* 6*2.5
3.1* 5.6*0.1
1
1
1
3
1
3
12*14
20*15*1
2
M1.7*6
2
2
2* 5*2.5
8
20.5*6.5*3.8
1
1
9
M2*12
6
1R360MXL 2.5
1
M2*5.5
7
1
1
2
2
M1.7*4
8.2* 4.3
2
110T
M3*8
2
1
67* 3*0.8
1
2
4
2
155* 5
M2*6
6
2M2*12
7.5 g
3
3M1.6*38*20
3
M2*8
6
1160*14
2
19* 10*287
1
2
1
2M1.4*5
12*254
1
1
3* 7*32
1
4
056 M1.7*4 6
M2*12
1
2.5* 2*3.2
Servo arm
Flat Fillister Head Phillips Screw
Flat Fillister Head Phillips Screw
Flat Fillister Head Phillips Screw
Washer
Main Shaft
Washer
Bearing
Canopy, Front
Tail Blade Grip
Tail Rotor Hub
Control Arm Bushing
Tail Rotor Pitch Lever
Spindle
Linkage Ball B
Tail Blade
Thrust Bearing
Washer
Spacer
Tail Rotor Pitch Control Slider Ring
Tail Rotor Pitch Control Fork
Bearing
Tail Rotor Pitch Control Slider Bushing
Tail Rotor Shaft Drive Pulley
Hexagon Socket Head Screw
Vertical Fin
Tail Boom Support Rod
Horizontal Fin
Hexagon Socket Head Screw
Double-sided Tape
Stabilizer
Hexagon Socket Head Screw
Spindle
Washer
Washer
Tail Servo Pushrod Guide
SERVO
Tail Servo Boom Mount
Tail Pushrod
Tail Rotor Shaft Drive Pulley Cap
Tail Boom
Hook-and-Loop Band
11.1V 1200mAh Battery
ESC
Double-sided Tape
Horizontal Fin Mount
Control Arm Bushing
Washer Head Phillips Screw
Anti-rotation Bracket
Nut
Servo arm
Push Rod
Servo
Plastic Cannula
Hexagon Pan Head Screw
Main Frame, Left
Main Frame Right
Washer Head Phillips Screw
Tail Case, Left
Tail Case, Right
Bearing
Blade Grip
Description
Bearing
Nylon insert lock nut
Main Blade
Thrust Bearing
Hexagon Socket Head Bolt
Hexagon Socket Head Screw
Step washer
Step washer
O-ring
Control Arm Bushing
Main Shaft
Centre Hub Cap
Hexagon Socket Head Screw
Main Rotor Head
Hexagon Socket Head Bolt
Pinion Gear
Tail Drive Belt Pulley
Tail Drive Belt Pulley Base
Mount Set
Main Gear
Flat Head Phillips Screw
Tail Drive Belt
Control Arm Linkage
Swash Plate
Control Arm Bushing
Flange Bearing
Retaining Collar
Bearing
Anti-rotation Pin
Hiller Control Arm
Linkage Ball
Main Tail Drive Gear
Push Rod
Set Screw
Flat Fillister Head Phillips Screw
Landing Skid
Landing Skid Land Cap
Landing Gear Strut
Motor
Motor Mount
Hexagon Pan Head Screw
Washer Head Phillips Screw
Flat Head Phillips Screw
Hexagon Socket Head Bolt
013
014
015
016
025
026
027
028
032
031
030
029
021
022
023
024
020
019
018
017
035
034
033
NO.
001
002
003
004
008
007
006
005
012
011
010
009
Quantity Specification Specification
Description
NO.
088
089
090
091
095
094
093
092
100
101
102
103
099
098
097
096
108
107
104
072
073
074
075
079
078
077
076
084
085
086
087
083
082
081
080
065
066
067
071
070
069
068
061
062
063
064
060
059
058
057
Linkage Ball
105
106
Quantity
Washer 2* 4*0.3
1
109 3-axis gyro
4* 5*0.55
1
110 Washer

16
Parts List
Main Blade Set Main Blade GripSet Main Blade SpindleSet Main Blade FixScrew Set
Main Rotor HeadSet Hiller ControlArm Set Push rod Set Main Shaft Set
Swashplate Set Belt Guide PulleySet Gear Connection ShaftSet
Main Tail Drive GearSet Main Gear Set(With Main Shaft) Main Frame Set Anti-Rotation Bracket
Motor Mount Pinion Gear 10Z Landing Skid Set Landing Gear Sruct
TailServo Boom Mount TailPushrod Guide Tail Boom TailRotor Pitch Lever Set
TailPushrod Set
DTS006324 DTS004035
DTS004036 DTS004037 DTS004038
DTS004039
DTS004495 DTS004494
DTS003922
DTS004094 DTS003925
DTS003926 DTS003969 DTS003927 DTS004095
DTS004097 DTS004099 DTS004102 DTS003928
DTS004105 DTS004110 DTS003930 DTS003931
DTS003929

17
TailServo
GWY003721
DTS003932
TailRotor Pitch Control Fork Set TailCase Set Vertical &horizontal tail blade set
DTS003935
TailRotor Hub
DTS003936
TailBlade Grip Rear stay bar TailBlade
DTS004044
TailRotor Spindle
O-ring TailDrive Belt
DTS003939 DTS004126
Ball Bearing
DTS004127
Ball Bearing Ball Bearing Ball Bearing
DTS004129 DTS004130
DTS004122
Ball Bearing
DTS003940
Thrust Bearing Thrust Bearing Servo Linkage Ball
DTS003941 DTS003942
Horizontal fin mountset
Canopy shoring
Canopy
483252.5 472.5
373
383.5 2.5 63
Hardware Set Allen Key
DTS004040 DTS004041
DTS004042 DTS004043
DTS004045
DTS004046
DTS004048
DTS004047 DTS004049 DTS004050

18
11.1V 1200mAh
KV 4050
2&3
GWY003770 GWY003751 GWY004011
GWY004540
High Frequency Transmission
Module, AHSS
GWY003768
LCD Setting Module
3.7V 1100mAh
GWY003746 DTS003950
GWY003752
DTS003951
GWY003914
GWY004716
GWY2013 3-axis Gyro
GWY 6TL\V2 2.4G Transmitter,
6CH, AHSS, &Receiver 3-axis Gyro
GWY003315
GWY 6TL\V2 2.4G
Transmitter, 6CH, AHSS, Silver
GWY005451
Remote Receiver
GWY004718
Swash Servo 25A BrushlessMotor ESC Li-Polymer Battery
Brushless Motor
Connection Wire
5A Charger Li-Po Battery ofTransmitter Charger Wire
G02 Flybarless ControlSystem
GWY006195
GWY006228
GWY006227
AH6R - Receiver
AH6T - 2.4GHz
6-Channel Transmitter Main Blade Set
DTS004034