DTX RA-S01 User manual

WIFI/GPRS+GSM
Smart Home Alarm System
Key Features:
WiFi network, internet push without charge
Zone names can be revised by users
IP camera APP integrated in the alarm APP
Work with smart socket, support scene/linkage settings for home automation

Preface
Key features
Technical information
Front side panel view
Backside panel view
Initialization
How to use APP
How to connect WiFi for host
Add equipment
Introduction of APP main interface
Sensor learning
How to learn RFID keypad
Zone attribution settings
Edit sensor attribution
Delete sensors
Host settings
Wireless relay outputs learning
The instruction for use wireless relay outputs
RF socket
RF siren
Control device
Delete device
Scene
How to add a scene
Delete scenes
Linkage
How to add a linkage
Four types linkage
Delete linkage
History
IP camera monitor function
Contents
1
2
3
4
6
6
6
7
8
8
9
10
11
12
12
12
14
15
16
16
17
17
18
18
19
19
19
21
22
22
23

Hotspot setup
Unbind equipment
Switch equipment
Authorization
Logout
Call up
Answer alarm call
Remote phone call control
Remote SMS control
Maintenance
25
26
26
27
27
28
28
28
29
30

1
Thanks for choosing our GSM+Wi-Fi/GPRS/SMS home alarm system.
GSM+Wi-Fi/GPRS/SMS home alarm system has implanted the most
advanced and popular Wi-Fi technology into traditional GSM alarm
system technology, with ver y simple wireless set up. It’s ver y convenient
for users to set up the alarm system via APP. Compared with traditional
SMS APP, Wi-Fi APP is with much more simple and quicker operation.
Caution:To ensure that you can enjoy the impeccable warranty service,do not
open the host-housing to repair and renovate by yourself or we will not
provide free warranty service.All the losses and the adverse consequences it
makes will be assumed by users.
Preface

2
9.Information push promptly when AC power failure/recovered or detectors in low
voltage
1.WIFI/GPRS/SMS + GSM home alarm system
When there is no WIFI, the host will work with GPRS network. If there is neither WiFi
nor GPRS network, then the alarm host will send alarm SMS and make alarm call.
Key features

3
Power supply: AC=100 ~ 230V 50Hz/60Hz
Working voltage: DC5V 2A
Static current: < 200mA (when not under charging status)
Alarm current: < 300mA
Backup Battery: 3.7V 1050mah
Standby time: 7 hours
Charging time: 3.5 hours
GSM frequency: 850/900/1800/1900MHz
GSM Transmission power: 2W(850MHz/900MHz);1W(1800MHz/1900MHz)
Wifi transmission Power: 1W
Receiving and emitting frequency: 433MHz (868MHz optional)
Wireless transmission distance: ＞100 m (Open space)
Working condition: temperature: -10ºC ~ 50ºC, humidity:5% ~ 80%
WiFi frequency:2.4G
Technical information

SOS
4
Display
Home Arm
SOS
Away Arm
GSM indicator WIFI indicator
LED
When host receive message, the display button will flash slowly, users can press the
display button to listen to the message. When someone make call to the host, it will
ring and the display button flash fast, users can press the display button to answer
the call.
Display
Away Arm
Front side panel view

5
SOS
If the GSM signal do not flash, that means GSM have not initiated yet.
If the GSM signal flash once, that means GSM have initiated.
If the GSM signal flash twice, that means there is SIM card.
If the GSM signal flash thrice, that means the host can make call .
If the GSM signal keep light on, that means the host has connected to server via GPRS
network.
WiFi Signal
If the WiFi signal do not flash, that means host WiFi have not initiated yet.
If the WiFi signal flash once, that means host WiFi have initiated.
If the WiFi signal flash twice, that means the host has connected with router.
If the WiFi signal keep light on, that means the host has connected to server via WiFi
network.
Home Arm
SOS
GSM signal:

K1K2
K1 K2
Sim card Slot
1. After switch on the host, short press the K2 button to close host hotspot.
2. After switch on the host, long press the K2 button to set the host to default.
3. After switch on the host, short press the K1 button to open the host hotspot.
Google Play
App Store
Available on the
Initialization
Apple user search: “Carener2"
Android user search: “Carener2"
How to use App
After download the APP in smartphone, user need register in APP. Click the
“Sign up free”button to go to register interface, enter phone number, email
address and password, then clink the “Confirm” button to save settings. Then
user can log in the APP.
First install SIM card and power the alarm host with adapter, then switch on
the alarm host.About 3 seconds later, the panel will make a long beep, then
initialization succeed.
Backside panel view
6

Step one: power the alarm host with adapter.
Step two: go to the WLAN interface of smartphone, find the host hotspot
whose name begin with IWTAC_.
Step four: log in APP, click the button, choose sub-menu “WiFi
Setup”,input the home WiFi name and password. And then click “Connect”
button in APP .The host will say “ start connecting”. And if the WiFi connection
succeed, the host will say “ connect network success “ .
Note: if you can not find that hotspot, please short press K1 button at the
back side of host to restart WiFi for host.
Step three: Connect that hotspot. (the host hotspot default password is
123456789)
Note: the encryption mode of your router should meet one of the following:
1. WPA-PSK TKIP
2. WPA-PSK AES
3. WPA2-PSK TKIP
4. WPA2-PSK AES
5. Unencrypted (without password)
How to connect WiFi for host
7

Away Arm: touch button to away arm the host, it will says “ start away
arm, arm success”. All sensors will be under arm status.
Home Arm: touch button to home arm the host, it will says “ start home
st
arm, arm success”. Then 1 defense line sensors and 24 hours defense line
nd
sensors will under arm status, 2 defense line sensors will under disarm
status.
Disarm: touch button to disarm the host, it will says “ disarm
success”. s t n d
Then the 1 defense line sensors and 2 defense line sensors will
under disarm status, only 24 hours defense line sensors under arm status.
Call: users can firstly set the alarm panel phone number in APP(take page 10
for reference),then press the button to make call to alarm host directly.
Log in APP application, click button,click button. Then choose
sub-menu “add equipment”, users now can scan the QR code of panel. The first
one who scan the QR code of host will become that host administrator.
Note: before users add equipment, please confirm the smartphone is connected
with workable WiFi/GPRS network but not the alarm host hotspot.
Introduction of APP main interface:
Add equipment
8

Log in APP application, slide the screen to Sensor List interface.
Step one: Click the [Add] button, the APP will go to New Sensor interface.
Step two: Input the sensor/detector name, choose defense type, and do other
functional settings, then choose Sensor Type and Sub Type. （take user manual
Step three: click the Add button, the host will say “ start learning, please trigger
Step four: trigger the sensor.And then the host will say “ learning success”.
page 10 for reference）
detector”
Step five: touch “Confirm” in APP when it tips “New sensor learned, need
refresh sensor list” .
Voice message : keep pressing the button and start to record the message,
release the button to end the recording. (Maximum 20s voice message can be
About 1 minute later, the display button on alarm host will flash slowly, families
members can press the display button to listen to the voice message.
recorded.)
Sensor learning
9

Log in APP application, slide the screen to Sensor List interface.
Step one: Click the “Add” button, the APP will go to New Sensor interface.
How to learn RFID keypad:
Step two: choose Sensor Type as “RFID”, then click the “Add” button. The host
will say “start learning, please trigger detector ”.
Step three : turn to keypad, press its backside tamper switch.
Once the keypad make a sound like “beep”, then coding succeed. Users can
touch“Confirm” when the APP tips “ New sensor learned, need refresh sensor
list.”
10

Alarm delay: It is that the host will not alarm until delayed time arrives.
Note: for alarm delay time setting part, users should take page 11 for reference.
Join link: If alarm sensor choose “join link”, then means this alarm sensor will
be active to work,if not chosen means will not work anytime in any status.
Defense Line:
24H defense line: it means 24 hours protection, the alarm sensors in this line
will trigger the alarm system whenever in arm status or disarm status, usually
panic button, smoke detector,gas leakage sensor, etc should be learned to
24H defense line.
1st defense line: it means perimeter protection, the alarm sensors in this line
will work in both away arm and home arm modes.
2nd defense line: it means interior protection, the alarm sensors in this line
will only work in away arm mode, but will be deactivated in home/stay arm
mode.
Door Chime: this function is suitable for main entrance gate installation to
remind home owners that someone is coming in when the alarm system under
home arm or disarm status.
Firstly,user need to program door sensor which want to set door chime
function in 2nd defense line.
Secondly open door chime function under the “sensor attribution” interface.
After setting succeed, if alarm system is in disarm or home arm status,
somebody open the main entrance gate,alarm host will make sound like
“ding-dong”.
Detect Door: if the door/window sensors choose “detect Door” ,then those
sensors will have smart zone function. That is, when users away arm alarm
host the system will automatically check whether doors and windows are
closed; alarm host will remind users which door or window is open.
Note: This function is only available for two way door/window sensor.
11
Zone attribution settings:

Sensor Type: the name of sensor
Sub Type: the type of sensor
Edit Sensor Attribution
Click each sensor and go to sensor attribution interface. Edit each sensor
attribution and then click [save] button to save settings.
Alarm time: users can set host alarm time to 0-15 minutes.
Log in APP application, slide the screen to the right side.
Delete sensors
Independent Zone: Every zone can be set to be independent zone, which only
can be disarmed by APP, but can't be disarmed by remote controllers. The
feature is suitable for important room or private room.
Phone NO.: users can input the alarm host number, set the host
password(default:1111), and then set 6 groups alarm call numbers and 2 groups
alarm SMS numbers.
Long press each sensor, APP will tip below picture, click [confirm] to delete that
sensor, click [delete all] to delete all sensors.
Note: for smart door sensor, please choose Smart door sensor.
Note: the Sub Type can not be changed here.
Host Settings
12

Volume: users can set Mute, Low or Loud for the panel volume.
Time Zone: connect network for alarm host, thenset time zone for host, then it
will automatically timing via internet.
Delay Set:It includes arm delay setting and alarm delay setting.
1.Arm Delay: Arm time delay setting is that the host will not be armed until
delayed time arrives. Therefore, when touch “ away arm” button on alarm
host,users will have time to deviate from house.
2.Alarm Delay: First user should active “alarm delay” function under the sub-menu
of“sensor attribution” which is mentioned in page 10. Then set time for delayed
alarm.This function is usually applied to leave time for disarm alarm host.
Ring time: the host can receive phone calls. It allow user to set the ring time from
0-90 seconds .When the ring time arrive, it will pick up the phone call for remotely
control .Users can take page 25 for reference of remote phone call control.
Auto Arm: this is the auto arm/disarm function. In total user can set three groups
auto arm/disarm time . For each group, user can set the arm time and disarm time,
choose the date from Monday to Sunday, then click the “activate” button to
activate that group time setting. Finally click the “save” button to save all settings.
Push alert: This Function is for setting AC fail and recover alert, Arm/Disarm alert,
alarm host battery low voltage alert, Sensor low battery alert, Wi-Fi ok or
disconnect alert , door open or close alerts.
SMS push: when the host do not connect with WiFi or GPRS, it will work with
GSM+SMS. If users activate the SMS push function, then users who is set to be
alarm SMS number[user manual page ** phone NO.] can receive SMS alerts of AC
fail and recover, Arm/Disarm, alarm host battery low voltage, Sensor low battery
,Wi-Fi ok or disconnect, door open or close.
Language: set language for host.
Note: it will take 30s-120s to switch language for host, because the host need
time to download the language file from server and install the new language
program.
13

Fourthly, press the learning button of relay, the indicator light of relay will flash
and .relay make switch sounds
Sixthly, disconnect power adapter from relay. And then reconnect power
adapter for relay. Then users can control relay outputs on APP.
Fifthly, users can click Yes button of the APP notice “Registering, does the
device have the right action ?” The APP will refresh the device list. And the
host will say “ learning success” .
Thirdly, Input device name, choose Device Type “ ” and choose Sub Typesocket
“ ”. Then click the Add button. The host will say “start learning,Relay-4Line
please trigger detector”.
Firstly, Connect wireless relay outputs with power adapter. To reset the relay,
user can long press its learning button about 6 seconds until the LED indicator
lamp lights on again.
Secondly, log in APP application, click the “Automation” button to enter the
device List interface. Then click the Add button to go to New Device adding
interface.
Wireless relay outputs learning
14

Attention:
When you plug the Jumper between the 1, 2 pins, four bulbs will
simultaneously be opened and closed, or opened /closed several of them;
when Jumper between the 2, 3 pins, you can only turn on one bulb once, for
example, if you have already opened the '1' bulb, when open the “2”
bulb,the'1' bulb will go off.
There are four groups of "A/B/C" in a relay and one group will control one set
of circuit. As known to all that only a closed circuit formed the appliance
works, that's to say the relay is a switch in this circuit. For example: If you
would like the beside lamp controlled by the first group, simply cut off the Fire
Wire of bedside lamp circuit and reconnect the two sides of A B. Of course, you
can also be cut off the zero line to plug in A and B of the first group as well.
Same goes for the second, third and fourth group.
15

Firstly, log in APP application, click the “Automation” button to enter the
Device List interface. Then click the Add button to go to New Device adding
interface.
Secondly, input device name, choose Device Type “ ” and choose Sub Socket
Type “ ”.Then click the Add button. The host will say “start learning, Socket
please trigger detector ”.
Thirdly, keep press the learning button of RF socket about 3 seconds and then
release, the indicator light of socket will flash and the socket will make switch
sounds.
Fourthly, users can click Yes button of the APP notice “Registering, does the
device have the right action ?” The APP will refresh the device list. And the host
will say “ learning success” .
Firstly, log in APP application, click the “Automation” button to enter the Device List
interface. Then click the Add button to go to New Device adding interface.
Secondly, input device name, choose Device Type “Siren” . Then click the Add
button. The host will say “start learning, please trigger detector”.
Thirdly, long press outdoor siren learning button for 3s or short press indoor siren
learning button to and start coding with alarm make sirens under learning status
host.
RF Socket
RF siren
16