Watchguard DIGITAL V2 User manual

Introduction:
This guide aims to give you a quick overview of the 5 basic steps required to install your WatchguardDigital
Security System, as well as its basic operation. It is important that you follow the step-by-step instructions
detailed in the full installation manual to ensure correct operation and full understanding of the system.
Once the locations for the main control unit and siren are chosen, connect power supplies and turn on the main
control box key switch and the siren key switch. Now test their operation before mounting the units permanently
to ensure that they are within the wireless radio range.
STEP 1.
MAIN CONTROL UNIT
Choose a convenient mounting location to install the main control
unit i.e. close to a phone outlet and power point. Drill mounting
holes (7mm Diameter) into the chosen location. Mount the unit on
the wall using the supplied screws and wall plugs.
CONNECTIONS
Remove cover plate then connect the phone line into the left side
phone socket. If you are using a phone / fax / PC already at your
available phone point, you may plug the lead from your existing
device into the right side socket. Plug the power supply into a
power point and switch on. Straighten the wire antenna for
maximum wireless range. Now turn the main key switch to the
ON position (do not press the remotes).
WATCHGUARD

DIGITAL V2
Quick Start Guide
Antenna
ON
OFF
AC POWER
SOCKET
STEP 2.
WIRELESS PIR DECTECTORS
Power the detector by
opening the case and
removing the plastic
insert between the
battery terminals. Wait 3
minutes for the detector
to warm up. During this
time you can work out
where you would like to
locate your detectors.
To test each detector’s
mounting location:
Put DIP switch 1 and 3
on the Main Control Unit
up. While holding the
detector in the mounting
position open and close
the detector case.
The main unit will beep
once. If the detector
passes, you will hear a
second set of beeps a few
seconds later. If this does
not occur, you must
reposition the detector
and retest.
Now you can mount your
detectors. Drill a 5mm
diameter hole into the
wall. Push the wall plug
into the hole then screw
in the mounting bracket.
The detector can now be
pressed onto the swivel
bracket. Re-test the
detector by opening &
closing the case and then
walking back and
forward in front of the
detector. The main unit
will beep each time the
Red PIR Detection LED
illuminates.
When completed for each individual detector, return all the
main unit dipswitches to off to exit this test mode.

Phone
Line
Power supply
Cover
Plate

STEP 3.
WIRELESS SIREN
Set the Main Control Unit
into wireless siren auto
test mode by setting DIP
switches 1 and 5 to ON.
Turn the external siren
keyswitch to ON and then
hold the siren in the
desired mounting position.
When this mode is entered
the strobe on the siren will
flash every 5 seconds, and
the main unit will beep out
the signal strength every 5
seconds. Note that the
siren must be moved until
a minimum of 3 beeps is
heard from the main unit.
Reset dipswitches to off.
Mount the siren if wireless
siren auto test was
successful.
Drill mounting holes,
(7mm diameter, 25mm
minimum in depth) into
the chosen wall. (If brick,
use the green star plugs &
press one into each hole.
Now make a 12 mm
diameter hole and push the
wires through the wall and
up into the ceiling for
power.
Screw the top 2 siren
screws half way in and
place the unit onto the
wall supporting itself from
the top 2 screws, then
screw in and tighten the
bottom two mounting
screws then finish
tightening the top two
screws. Run the power
supply wire through the
roof to the closest power
point, connect power
supply and switch on.
STEP 4.
OPERATION
(Ensure main unit keyswitch is ON)
Press
Button 1
Press
Button 2
Press
Buttons 1 & 2 Together
AWAY mode
Press once
to arm the system in
normal AWAY mode.
The internal
screamer will beep at 1-
second
intervals for the 30-
second exit delay
and the outside siren will beep once.
The strobe will flash once.
STAY mode
Press twice within 3 seconds
to arm
the system in STAY mode.
The
internal screamer will beep at 2
-
second intervals for the 30-
second
exit delay and the outside siren will
give a low tone beep
after the second
press.
Panic mode
Press and hold (3 seconds
) to
activate PANIC mode, the outside
siren will sound and the strobe will
flash but the internal screamer will
not sound.
DISARMING
Press once to disarm the system. The
siren will beep twice. The strobe will
flash for 5 seconds.
QUIET ARMING and
DISARMING
(i.e. No External Siren Beeps)
For quiet AWAY
arming or
DISARMING
press both buttons
together, once
For quiet STAY
arming press both
buttons together simultaneously,
twice within 3 seconds.
STEP 5.
SYSTEM REGISTRATION & MONITORING SET-UP
Now that the physical installation is complete you will need to create a SecureNet
Alarm Monitoring Account.
Please visit www.watchguardalarms.com.au and click on the ‘Create Account’
button and then follow the instructions.
If you do not have internet access, please call 1300 653 533 to complete a phone
registration. Once you have registered your installation is complete.
IMPORTANT NOTE:
When testing the operation of the system you will NOT
be contacted by SecureNet if the alarm is triggered but
then cancelled (disarmed) within 30 seconds.
OFF
ON











