DU-HA 70827 User manual

DETAIL G
SCALE 1 / 8
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
All-Terrain Storage Box Lid7082011
Screw #10-24 x 1.50 SS100100622
Washer - Flat #10 x 1/2 OD SS
100114323
Handle - 90 Degree Metal- Black100104424
Nut Nylock #10-24 SS10011442
5
Washer - Bond Seal #10 SS
100124426
G
70827 - All-Terrain Mounting Kit -
Kubota RTV 900 & older Kawasaki
Mule
STEP 1 - Attach Handle to Lid
Place Handle (4) over holes in Lid Top (1). Insert two Bolts
#10 x 1.5" (2) through Flat Washer - #10 (3), Handle (4) and
All-Terrain Lid (1). Secure with Flat Sealing Washer #10 (6)
(has a rubber backing) and Lock Nut #10 (5) Use 1/8" Hex
Key Wrench.
Note: Handle may already be installed.
All-Terrain

Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
DU-HA All-Terrain Storage Box7082011
All-Terrain Universal Mounting Plate100127122
Bolt Hex .25 x 1.00100119583
Washer Flat 1/410011558
4
Spacer 1" OD x 3/8"10011828
5
Washer Lock 1/4"
100101086
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
DU-HA All-Terrain Storage Box7082011
Kubota RTV 900 & Older Kawasaki Box
7082712
All-Terrain Universal Mounting Plate100127123
J-Bolt 1/4-20 x 2.5 SS10012672
4
Nut Nylock 1/4-2010011222
5
Washer Flat 1/4
100115526
70827 - All-Terrain Mounting Kit -
Kubota RTV 900 & Older Kawasaki
Mule
Step 2: Attach Plates to Box
Attach the Universal Mounting Plates (item 2) to the bottom of the
All-Terrain Storage Box (item 1) using 1/4-20 x 1 bolts (item 3), 1/4
lock washers and 1/4 washers (item 4), make sure to use the
Spacers (item 5) between the mounting plates (item 2) and the
All-Terrain Storage Box (item 1). Next measure the width of your
UTV box and adjust your mounting plates (item 2) so the outer center
square slot will line up with the outside of box on your UTV. Make
sure to orientate the mounting plates (item 2) with the larger slots
facing outward, as shown in Detail C.
Step 3: Set Box on UTV
Set the All-Terrain Box (item 1) onto the UTV Box in your desired
postion. Make sure you have enough room to open the lid without
hitting the cab.
Step 4: Secure Box to UTV
Secure the All-Terrain Box (item 1) to the UTV Box (item 2) by
inserting the 1/4-20 x 2.5 J-Bolt (item 4) into the center slot on the
Universal Mounting Plate (item 3) hook the J-Bolt onto the lip on the
UTV Box (item 2). Secure with 1/4" Washer (item 5) and 1/4" Nylock
Nut (item 6) on each side of UTV Box.
All-Terrain
3
4
2
5
1
4
1
3
6
5
2
6

All-Terrain

Place Rubber T-Handle (7) over inserts in Base (2). Insert two Screws
#10-32 x 1.0'' (8) through T-Handle (7) and use 1 /8" Hex Key Wrench
to tighten into the inserts, on each end, T-Handle should point outward
when in the up position. Next install the Rubber T-Handle Keeper (6)
on the lid, make sure the alignment knob on the back of the T-Handle
Keeper lines up with the recess in the lid (1) and secure in place with
one Screw #10-32 x 1.0" (8) by inserting through the T-Handle Keeper
(6) and thread into the insert in the lid, on each end.

Place each Foam Organizer / Gun Holder assembly (3) into the channel
slots in the side walls of the ALL-TERRAIN Box (2). They can be
positioned in 3 locations on each end or in the center of the
ALL-TERRAIN Box. To install rotate horizontally above slot and rotate
downward and slide into slot. Stock of gun should rest in large
groove; barrel should rest in small groove.

To maximize strength and stability, use the Center Brace (5). Insert
each end into the holes on the top lip of the ALL-TERRAIN Box (2) at
the middle. To access cargo, lift front side of Center Brace out of the
hole and rotate the Center Brace out of the way to the right and insert
into storage hole on back side of ALL-TERRAIN Box (2). Return Center
Brace to front hole when finished.

To close the Humpstor shut the lid and secure end T-Handles (7) by
grabbing the top of the rubber handle and pull up and secure onto the
Rubber T-Handle keeper (6) on each end. Next on top of the lid (1) turn
the Wing Knob 1/4 Turn Latch (4) counter clockwise to engage locking
mechanism. To lock Humpstor, use the provided key. Insert key with
teeth facing away from you into Wing Knob 1 /4 Turn Latch (4) and
turn counter clockwise to lock and clockwise to un-lock.
Parts List
ITEM QTY PART NUMBER DESCRIPTION
1 1 70820 All-Terrain Storage Box Lid
2 1 70820 All-Terrain Main Body
3 1 Divider 70800 Assm Divider Pkg Assm - Humpstor 2022
4 1 1001232 Wing Knob 1/4 Turn Latch
5 1 1001239 Center Wire Brace
6 2 1001235 Latch -Rubber T-Handle -Keeper
7 2 1001235 Latch -Rubber T-Handle
8 6 1001260 Screw BHSCS #10-32 x 1" SS
Safety Instructions:





