Dual DXRM58BT User manual

Quick Start Guide
Digital Media Receiver with Bluetooth
DXRM58BT
®

Installation
Before You Start
• Dual always recommends professional installation.
• Disconnect negative battery terminal.
• Remove trim ring from unit (if installed).
Note: Most vehicles require an installation kit, wiring harness and/or antenna
adapter (all sold separately) to properly install the head unit in the vehicle.
Installation Process
1. unit.
2.
Carefully remove the existing head
Connect wiring harness.
3. Mount the head unit using the mounting sleeve or ISO brackets (depending on
your vehicle’s dashboard).
4. Connect wiring harness and antenna. Test the head unit for correct operation.
5. Slide into mounting sleeve to secure, or mount the ISO brackets to the vehicle.
6. Snap trim ring into place.
Wiring Connections
The chart below the connection for each wire in the wiring harness.
Color Connection
Red 12V Ignition / Accessory
Yellow 12V Battery / Memory
Black Ground
Blue Power Antenna / Amp Turn-on
Grey Right Front (+)
Grey/Black Right Front (-)
White Left Front (+)
White/Black Left Front (-)
Violet Right Rear (+)
Violet/Black Right Rear (-)
Green Left Rear (+)
Green/Black Left Rear (-)
Fuse:
When replacing the fuse, make
sure new fuse is the correct type
and amperage. Using an incorrect
fuse could damage the radio.
Tip:
When a suitable ground wire is
not present in the vehicle wiring
harness, connect the black ground
wire to the vehicle chassis.

Installation
Double DIN
Dashboard or Installation Kit
Head Unit
Double DIN
Head unit
Metal Bracket
PLASTIC TRIMRING
SCREW
Dashboard or
Installation Kit
Double DIN
Double DIN
Mounting Tabs
Dashboard or Installation Kit
Mounting Sleeve
(Not included)
Mounting Sleeve
(Not included)
Mounting Sleeve
(Not included)
Step 1:
Insert the mounting sleeve into the
installation kit or dashboard.
*Mounting Sleeve is Not included.
Step 2:
Bend multiple mounting tabs around
the mounting sleeve until the mounting
sleeve is secure.
Step 3:
Connect all wiring harnesses and slide
the head unit into the mounting sleeve
until it clicks into place.
Using the existing
brackets or the brackets
supplied with the
installation kit, mount
the brackets to the sides
of the head unit with the
screws supplied with the
head unit.
Mounting the Head Unit:
ISO mounting
Mounting the Head Unit:
Typical DIN mounting

General Operation
Power On/Off
Changing Modes
Volume
Mute
Auxiliary Inputs
Reset
Setting the Clock
Audio / Menu
Press the /MODE button to turn the unit on. Press and
hold /MODE button to turn unit off.
Press MODE to select between Radio, USB,
AUX, Bluetooth.
Modes of operation are shown in the display.
Adjust volume using volume knob.
Press to silence the audio. Press again to resume
listening at the previously selected volume.
Insert a 3.5mm cable in the units front AUX port.
Press the RESET button to reset the unit back to the
factory settings if abnormal operation occurs. The reset
button is located on the front panel.
Display With the unit on, press and hold DISP to display clock time.
Press and hold DISP to toggle display between various
displayed information.
Press and hold volume knob to select clock setting mode.
Rotate the volume knob to right to adjust hours and rotate
volume knob to left to adjust the minutes.
Press volume knob momentarily to select between the
audio functions. Press and hold volume knob for more
than two seconds to select between the menu functions.
Rotate the volume knob left/right to adjust or activate the
desired function/audio.
Faceplate Removal Press RELEASE and pull away from the right side to
remove. To re-install, insert left side of faceplate
first then push right side to secure.

AM/FM Tuner Operation
Seek Tuning
Manual Tuning
Band
Storing Presets
Recalling Presets
Press TUNE or TUNE to seek to previous or next
strong station.
Press and hold the TUNE or
TUNE to enter manual
tuning mode. Then press TUNE or TUNE momentarily
to move radio frequency down or up one step at a time.
Press and hold TUNE or
TUNE to advance quickly.
Press BAND to select between FM1, FM2, FM3, AM1
and AM2 bands. Up to six presets can be programmed
for each band, enabling up to 18 FM stations and 12 AM
stations to be stored in memory.
Up to 18 FM and 12 AM stations can be stored. To store
a station, select the desired band and station. Press and
hold the desired preset button (1-6) for more than two
seconds. When stored, the preset number will appear in
the display.
Preset stations can be recalled any time by pressing the
corresponding preset button.
Auto store Press and hold AS for more than 2 seconds to store
18 FM stations and 12 AM stations automatically.
Preset Scan Press the AS/PS (on remote control) to recall each preset
station that stored in the memories in each band.

USB Operation
Playing MP3 Files
Track Select
Fast Forward and
Reverse
Pause
Folder Access
Repeat
Random
Intro
To play MP3 files, insert a USB device containing MP3 files.
Press TUNE to skip to the beginning of the next song.
Press TUNE to skip to the beginning of the previous
song.
Press and hold TUNE or TUNE to fast forward
or reverse a track.
Press
l
/ II to temporarily stop playback.
Press
l
/ II again to resume playback.
Press RPT to toggle between RPT ALL,RPT FLR and
RPT ONE.
• RPT ALL - Plays all tracks on USB device.
• RPT FLR - Continuously repeats all files in current folder.
• RPT ONE - Continuously repeats selected track.
Press RDM
cancel the
to play tracks in random order, press again to
RDM function.
Press INT to plays first 10 seconds of each track, press
again to cancel the INT function.
Folder can be found by pressing Folder Up or Folder Down.
About 1 second after the folder name is displayed, the first
file under the selected folder will be displayed and playback.
•RDM ON - Plays all tracks in random order.
•RDM OFF - Cancels the RDM function.
•INT ON - Plays the first 10 seconds of each track.
•INT OFF - Cancels the INT function.

Preparation
Pairing a New
Device
Bluetooth®
Before using a Bluetooth device, it must be paired and
connected. Ensure that Bluetooth is activated on your
device before beginning the pairing process.
The head unit broadcasts the pairing signal constantly
when no devices are connected. Complete the pairing
sequence from your Bluetooth device. Refer to the
owner’s manual for your device for more details.
The device name is “DXRM58BT”
The Bluetooth passcode is "1234”
Streaming Audio
Troubleshooting
•Press to skip to the next available audio track.
•Press to skip to the previous audio track.
•Press / II to toggle between play and pause during
playba
l
ck.
Note: If passcode "1234" does not pair your device to
the receiver, use passcode "0000".
Note: The head unit can be in any mode of operation
when pairing is performed.
The head unit supports A2DP wireless streaming audio
from a Bluetooth mobile device directly to your head unit.
The following functions can be used to control the music:
Operation

FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
When it comes to quality car stereos, Dual is the brand you can depend on.