Dualit DCT2i Installation instructions

Conveyor Toaster
Installation, Operation and Guarantee
Original Instruction
Please carefully read this manual before using this product. Make
sure you are familiar with all of the safety and usage instructions.
Keep this manual in a safe place for future reference.

02 03
CONTENTS
Safety Precautions 04
Before First Use 05
Know Your Conveyor Toaster 06
Set Up 08
Use 10
Cleaning - Daily 13
Guarantee 14
Troubleshooting 15
Unpack the box with care, keeping all the packaging materials until you are satised everything
is present and in working order. Once satised remove any tags from the appliance body and
recycle the packaging appropriately. Do not remove tags from the cord. You may wish to keep
the box to store your appliance.
All illustrations are for representation only, your model may have a different appearance from illustrations shown.
DON’T FORGET TO
REGISTER YOUR PRODUCT
Fast and efficient customer
service important safety
advice, access to manuals and
product information should
you require assistance with
your purchase.
A library of
mouth-watering
recipes and regular
articles and blogs.
Be the first to hear about
exciting new Dualit products.
1 2
3
Dualit recommends safety rst: please register your product so that
we can contact you in the unlikely event that a safety notication is issued.
Remember to keep your receipt as proof of purchase.
Take a minute to register your product
with us to receive these outstanding benefits:
WWW.DUALIT.COM/REGISTER

04 05
•Keep area around the Air Intake clear.
•Only touch the dials during operation as
surfaces get very hot. Risk of scalding.
•Do not place anything on top or near the sides/
underneath of the appliance. Risk of re.
•The bread may burn, therefore do not use the
appliance near or below combustible material,
such as curtains. Risk of re.
SAVE THESE
INSTRUCTIONS
In the interest of improving products, Dualit Ltd. reserves the
right to change the product specication without prior notice.
All illustrations are for representation only, your model may
vary from illustrations shown.
INSTRUCTIONS ON
ENVIRONMENT PROTECTION
Do not dispose of this product in the
usual household garbage at the end
of its life cycle. Please hand it over to
a collection point for the recycling of
electrical and electronic appliances. The symbol on
the product, the instruction of use or the packaging
will inform you about the methods of disposal.
The materials are recyclable as mentioned on its
marking. By recycling, material recycling or other
forms of re-utilization of old appliances you are
making an important contribution to protect our
environment. Please enquire at the community
administration for the authorised disposal location.
BEFORE FIRST USE
•Read this instruction manual before you start
using the appliance. It gives you important safety
information and will ensure you get the most
out of your Dualit product. Make sure all people
associated with the appliance’s use understand
the operation and safety before they use the unit.
•Keep this manual and your proof of purchase in
a safe place.
•Don’t forget to register your product at
www.dualit.com/register.
•Remove all visible packing material, and those
from inside the cooking chamber.
•Before making any electrical connection to this
unit, check that the power supply is adequate for
the voltage, amperage and requirements stated
on the rating plate.
IMPORTANT SAFETY PRECAUTIONS
READ ALL
INSTRUCTIONS
READ ALL INSTRUCTIONS
BEFORE USING THE PRODUCT.
KEEP THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
IMPORTANT
SAFEGUARDS
• THIS IS AN ATTENDED APPLIANCE.
Do not leave unattended during use,
unplug after each use (risk of re if an
unattended appliance is left operating).
•This appliance must not be used by children
younger than 8 years old or persons with very
extensive and complex disabilities. Children
aged 8-14 years and persons with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge shall not use this
appliance, unless they are supervised and have
been given instruction concerning the use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made
by children unless they are older than 8 and
supervised. Keep the appliance and its cord out of
reach of children less than 8 years old.
•This appliance is intended for indoor professional
use only. Do not use outdoors.
•This appliance is only to be installed in locations
where its use and maintenance is restricted to
trained personnel.
Electrical safety
• Turn off and unplug after use. Risk of re
if unattended appliance is left operating.
•Do not use appliance if dropped, cracked or
damaged. Risk of re, electric shock or
injury to persons.
•Ensure the appliance is correctly earthed. Risk of
electric shock.
•Ensure the electrical supply is 240V UK mains.
•Do not operate the appliance if it has started
to malfunction. Risk of shock, injury and
scalding.
•Do not remove or alter the supplied plug or
power cord. Risk of electric shock.
•Do not operate the appliance with a damaged
power cord or plug. Risk of electric shock.
•If the power cord becomes damaged it must
be replaced by Dualit or an authorised Dualit
repairer.
•Do not pull the power cord over sharp edges,
clamp it or allow it to hang down. It should not
be allowed to come into contact with hot or
damp surfaces.
•The use of extension cables not authorised by
the manufacturer may cause damage, accidents
or re.
•Unplug from the mains before cleaning, servicing
or maintaining the appliance.
•If using the appliance close to a wall, ensure
this is clad with non-combustible material and
adheres to re prevention regulations.
•Use the correct replacement detachable fuse.
Never use a plug without the fuse. Replacement
fuses should be ASTA approved to BS 1362.
•Never touch the appliance with wet hands.
Risk of electric shock.
•This appliance conforms to directive 2014/30/
EU regarding electromagnetic compatibility.
•We recommend that the appliance is plugged
into a socket that has no other appliance
connected to it. Failure to do this may cause an
overload, trip a circuit breaker or blow a fuse.
Preferably the socket outlet should be protected
by a residual current device (RCD).
•In case of re, disconnect from the power source
immediately.
• CAUTION: In order to avoid a hazard due
to inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through an
external switching device, such as a timer, or
connected to a circuit that is regularly switched
on and off by the utility.
•The appliance is not intended to be operated by
means of an external timer or separate remote
system.
General safety
• For bread use only. Do not use products
that may leak liquid sugar when heated as
this poses a re risk.
•Do not allow the device to freeze. This may
compromise electrical safety and will degrade
performance of all lubricants.
•Do not immerse any part of this appliance in
water or other liquids. Risk of electric shock.
• CAUTION: outer surfaces of the appliance
will be hot during use. Risk of scalding.
• CAUTION: the appliance will remain hot after
use. Risk of scalding.
•Allow the appliance cool before cleaning,
removing or installing parts. Risk of scalding.
•Do not attempt to dislodge bread when the
toaster is plugged in. Risk of electric shock
and scalding.
•Do not place the appliance close to sources of
heat such as electric rings, hot ovens or open
ames. Risk of re.
•The machine must only be operated on a at
surface.
•The use of accessories or attachments not
recommended by Dualit. Risk of re, electric
shock or injury to persons.
•Do not place the appliance on a polished wood
surface, it could damage the surface.
•Do not use the appliance for any purpose
other than the intended use as described in this
instruction book.
•Do not operate unit without crumb tray as this
will cause uneven toasting and possible over
heating of the appliance. Risk of re.
•Crumb Tray should be regularly cleaned. A build
up of crumbs can burn. Risk of re.
•Keep body parts away from moving parts of the
appliance. Risk of injury to persons.
•Never use sharp or abrasive objects or cleaners
on any part of the appliance.
•Never put the appliance or part of it in a
dishwasher.
•The appliance must not be cleaned by a water
jet.
•Do not modify the appliance.
•Clean before rst use.
•Remove all packaging before use. Risk of re.
•Do not use metal utensils to remove bread or
crumbs from the appliance. Risk of electric
shock.
•Do not store or use gasoline or other
ammable materials near the appliance. Risk of
re.
•Tie hair back and remove lose clothing or
jewellery to avoid them getting caught in the
moving parts of the appliance. Risk of injury.
•Never place hands or implements into the
toasting chamber. Risk of shock, injury and
scalding.
•Never touch the Conveyor Belt. Risk of
shock, injury and scalding.

06 07
KNOW YOUR
CONVEYOR TOASTER
MODEL: DCT2I
U
N
P
L
U
G
W
H
E
N
N
O
T
I
N
U
S
E
S
W
I
T
C
H
O
F
F
&
CONTROLS
FUSED PLUG
READY INDICATOR
ILLUMINATES GREEN WHEN THE
TOASTER IS QUICK START READY. SEE
PAGE 10 FOR DETAILS.
POWER INDICATOR
ILLUMINATES RED WHEN THE TOASTER
IS PLUGGED IN AND SWITCHED ON.
FUNCTION CONTROL DIAL
USE TO CHANGE THE TOASTING
FUNCTION: TOAST, BAGEL, STANDBY
OR OFF.
TOAST SETTINGS DIAL
USE TO ADJUST BROWNNESS OF YOUR
BREAD:
SETTING 1 - LIGHTEST
SETTING 9 - DARKEST
BREAD RAMP
KNUCKLE GUARD
REMOVABLE CRUMB TRAY
CONVEYOR BELT
LEGS
BREAD SLIDE
TOAST RAMP
ANTI-TAMPER GUARD
M4 X 10.0MM SCREWS
FIT WITH PHILLIPS HEAD SCREWDRIVER
AIR INTAKE UNDER MACHINE

08 09
SETTING UP YOUR CONVEYOR TOASTER
Note: Before setting up your Conveyor Toaster ensure that you remove the legs and Anti-Tamper Guard
from the polyfoam insert in the bottom of the box.
Caution: The surfaces of
the Conveyor Toaster will
get extremely hot during
operation. Ensure to touch
only the dials when in
use, as risk of scalding. Do
not place items on top of
the Conveyor Toaster, in
particular plastic such as
bread bags that could melt.
4
Position the Crumb Tray
into the mounting rails
beneath the Conveyor
Belt. Caution: Failure to
do so could cause the
appliance to overheat.
POSITION CRUMB
TRAY
3ATTACH LEGS
Carefully place your Conveyor
Toaster on its side. Thread all
4 legs into the holes shown
and tighten using a 21mm
spanner. Pick up and place the
Conveyor Toaster on its feet.
Caution: do not operate
without all legs secured.
POSITION
9
Place the Conveyor Toaster
on an open level surface.
Ensure that it is positioned
100cm away from any
overhanging cupboards or
ceilings.
2UNPACK
REMOVE
PACKAGING
BEFORE
INSTALLATION
Caution: ensure all
packaging material
is removed from the
Conveyor Toaster.
Remember to keep it
until you are satised that
everything is present and
functional.
11 NEVER COVER
THE VENTS
Never cover the vents on
the sides of the Conveyor
Toaster. This will prevent
necessary air ow and
could cause a re.
U
N
P
L
U
G
W
H
E
N
N
O
T
I
N
U
S
E
S
W
I
T
C
H
O
F
F
&
Position the Bread and Toast
Ramps as shown above.
Note: Once the Bread
Ramp has been positioned,
it cannot be moved. Dualit
recommend having a basket
underneath the Toast Ramp
to catch toasted items.
5POSITION RAMPS 12 CAUTION: HOT
SURFACES!
Take time to wipe down
your Conveyor Toaster with
a damp cloth to ensure it is
ready for toasting.
WIPE MACHINE
6
Ensure your Conveyor
Toaster is not stored in
an appliance garage or
underneath cupboards.
Overheating may occur if
the appliance is not correctly
positioned. Risk of re.
DON’T STORE
UNDER CUPBOARDS
78DON’T STORE
NEAR CURTAINS
Do not store or use your
Conveyor Toaster next
to curtains or ammable
material. A re may occur
if incorrectly positioned.
POSITION
Ensure the Conveyor Toaster
is positioned at least 50cm
clear from walls. For best
results use away from drafts.
Warning: do not use near
water sources.
10
DON’T FORGET
TO REGISTER
YOUR PRODUCT
WWW. DUALIT.COM/REGISTER
OR BY POST
1
Register your appliance at
www.dualit.com. This will
only take 60 seconds. You
will need the product model
and serial numbers that are
on the rating label on the
base of the product.
REGISTER MY
APPLIANCE

10 11
TOASTING
Plug in and switch on your Conveyor Toaster at the wall.
Choose your function by turning the Function Control Dial to the desired setting.
Toast: Top and bottom elements are on. Both sides of the bread will be toasted.
Bagel: Only bottom element is on. Place bagels cut side down on the conveyor.
Standby: Do not use for toasting. See page 12 for details.
Using the table below as a guide, adjust the Toast Settings Dial based on how you like your
bread; clockwise for darker and anti-clockwise for lighter.
*Toaster will be too hot so will burn the bread. Risk of re. **Bread will not toast properly and will be soggy.
USAGE TYPES
Continuous Toasting
(toast every 1-5 secs)
Back to back or larger
batches.
Intermittent Toasting
(toast every 5-30 secs)
Buffet Toasting
(toast every 30+ secs)
#Irregular intervals over 30
seconds, used on demand.
Reminder
• If using the toaster front of house, we recommend selecting a suitable browning colour for
the days delivery of bread before service starts, and that Quick Start is not used. It is also
recommended that the Anti-Tamper Guard is tted to prevent customers changing the
settings. See page 13 for details.
• To achieve the maximum performance from your Conveyor Toaster, load continuously as
per the diagram above. For best results use day old bread.
• When swapping between functions; toasting continuously or intermittently, or changing
bread type, you should adjust your toast settings. See the table above for recommendations.
• When it’s time to turn off your Conveyor Toaster, change the Function Control to ‘OFF’,
wait for the Cooling Fan (audible) to stop, switch off and unplug the appliance from the wall.
Note: The Cooling Fan can take up to 10 minutes to switch off. Warning: Fire risk if
appliance is left unattended at any time.
Type of
Bread
Quick Start - Toast Setting Full Temperature - Toast Setting
Continuous Intermittent Buffet Continuous Intermittent Buffet
White 6 5.5 5 5 4.5 4
Granary 9 8.5 8 6 5.5 5
Fruit Bread 4 3.5 3 2.5 Not recommended*
Rye Not recommended** 9 8.5 8
Bagel 6.5 6 5.5 6 5.5 5
USING YOUR CONVEYOR TOASTER
CORRECT TOAST SETTING: IMPORTANT INFORMATION
Your Conveyor Toaster is designed to toast bread products in buffet and kitchen environments.
To achieve optimum performance, make sure that any user understands how to operate and
control the toaster for intended use.
Note: For new toasters, or those that haven’t been used in a while, follow the Setting Up guide
on page 8
WARM UP PROCEDURES: FULLY WARM AND QUICK START
FULLY WARM START UP PROCEDURE
Dualit always recommends this procedure when time is available. Switch on and allow your
Conveyor Toaster to run empty. The Conveyor Toaster will be fully warm after 30 minutes. This
procedure produces the most consistent toasting results and no adjustment of the toast settings
are required by the operator once toasting has started. See the diagram below and the table on
page 11 which help explain the differences between Quick Start and Fully Warm start procedures.
QUICK START PROCEDURE
If time is short, the Conveyor Toaster can be ready to start toasting in as little as 5 minutes.
As soon as the green Ready Indicator illuminates, you can start toasting. Begin by using the
Usage Type and toast setting for your bread as per the table on page 11. The Toast Chamber
will continue to heat up for 30 minutes until it reaches Fully Warm, after which it is important
to reduce the toast settings in order to maintain the consistent browning of your toast. Dualit
recommend that after 10 minutes of Quick Start toasting, the operator should reduce the toast
settings to half-way between the initial Quick Start toast setting and the Fully Warm toast setting.
See the table on page 11 for more information.
TOASTER WARM UP CHART
TEMPERATURE OF TOASTER
FULLY WARM
SWITCH ON
WARMING UP FULLY WARM
QUICK START
DURING THIS
PERIOD THE
TOASTING SETTING
WILL NEED TO BE
MONITORED AND
REDUCED AS THE
TOASTER WARMS
UP
FULL TEMPERATURE
TOASTING
STABILISED, NO
NEED TO ADJUST
TOASTING SETTING
UNLESS BREAD
TYPE OR USAGE
CHANGES
TIME (APPROX)
READY LIGHT ON (GREEN)
# #

12 13
TECHNICAL PARAMETERS
14kg
See the data plate on the base of the machine
W: 430 mm x H: 413 mm x D: 512 mm
560 slices per hour
CLEANING - DAILY
Before cleaning your Conveyor Toaster, tie hair back and ensure that you are wearing no loose
clothing or jewellery. NEVER ALLOW A BUILD UP OF CRUMBS IN THE CRUMB
TRAY AS THIS MAY CAUSE A FIRE. CLEAN DAILY.
STANDBY MODE
During periods of inactivity, you can use Standby Mode to reduce the power consumption of
your appliance by up to 70%. When you are ready to go again, switch the control dial to either
‘TOAST’ or ‘BAGEL’ and, in normal conditions, your machine will be ready to toast in just 2
minutes; that’s a 50% time saving over Quick Start.
After 15 minutes on standby, your Conveyor Toaster will have used the same amount of
energy as it would to get from room temperature to Quick Start temperature. As such, Dualit
recommends switching the device off if you don’t intend to use it for longer than 15 minutes.
ANTI-TAMPER
Your Conveyor Toaster features a removable Anti-Tamper Guard. Note: Before setting up
your Conveyor Toaster, ensure that you remove the legs and Anti-Tamper Guard from the
polyfoam insert in the bottom of the box. For buffet environments, Dualit recommends t-
ting the Anti-Tamper Guard to avoid customers adjusting the Toast Settings Dial. The Guard
should be tted using M4 x 10.0mm screws and a Phillips head screwdriver. After selecting the
correct toast settings, the Anti-Tamper Guard can be tted as follows.
TOASTER STANDBY CHART
TEMPERATURE OF TOASTER
FULL TEMPERATURE
START STANDBY
MODE
STANDBY TIME (15 MINS) WARMING UP (15 MINS)
∞
DURING THIS
PERIOD THE
TOASTING
SETTING WILL
NEED TO BE
MONITORED
AND REDUCED
AS THE
TOASTER
WARMS UP
FULL TEMPERATURE-
TOASTING
STABILISED, NO
NEED TO ADJUST
TOASTING SETTING
UNLESS BREAD
TYPE OR USAGE
CHANGES
TIME (APPROX.)
QUICK START
(13 MINS)
1
1
REMOVE SCREWS
REMOVE CRUMB
TRAY
LEFT SCREW
UNPLUG & COOL
2
2
RIGHT SCREW
WIPE
Insert and tighten the left-hand
screw.
Unplug from mains, leave
to cool for minimum
of 1 hour, then wipe all
external surfaces with a
damp, non-abrasive cloth.
Insert and tighten the
right-hand screw. To remove,
repeat in reverse order.
Remove Crumb Tray, tip out
all of the crumbs, then clean
with a damp cloth and replace.
Ensure the area around the
Conveyor Toaster is clean
and crumb free. Clean the fan
air intake with a damp, non-
abrasive cloth.
3
3
Remove the two screws seen
on the left and right-hand
sides of the controls. Align the
Anti-Tamper Guard with the
screw holes.
Remove the Crumb Tray. From
a cold start, set the Conveyor
Toaster to standby. Select toast
setting 9. As the conveyor
rotates, clean the exposed
section of the belt. Wipe with
a damp, non-abrasive cloth if
lightly soiled or a dry, lightly
abrasive pad if heavily soiled.
Then wipe with a damp cloth.
Your toaster is tted with a temperature limiting thermostat. During periods of inactivity,
longer than 5 minutes, the elements will turn off (indicated by the red power indicator going
off). Only introduce bread to the conveyor when the red light is on and the elements are
glowing cherry red.

14 15
GUARANTEE
This appliance is of excellent quality and construction. However, if any defects in materials or
workmanship do appear during the rst year from purchase, we will, at our discretion, either
repair or replace the defective parts, free of charge, subject to the terms and conditions of our
Guarantee shown below.
This Guarantee covers both parts and labour.
Carriage is not included.
Your Guarantee period is as follows:
If your conveyor toaster fails within one
year from date of purchase we will repair
or replace it free of charge, except for the
elements, provided:
• You have not misused, neglected or
damaged it.
• It has not been modied.
• You supply your receipt to show when you
bought your toaster.
Elements are guaranteed for 3 months
from date of purchase for parts and
labour, thereafter parts only. If located in
a congestion charge zone, the customer is
required to pay the charge. If over one year,
contact Dualit for recommended repair
agents.
This Guarantee provides benets which are
additional to, and do not affect, your
statutory rights. This Guarantee does not
cover the cost of returning the product to
the dealer from whom it was purchased or
to ourselves. This Guarantee applies only to
products sold and located in mainland Great
Britain. It does not cover liability in respect of
or replacement of plugs, cables or fuses and
also does not cover defects due to:
• Failure to use or maintain product in
accordance with Dualit’s instructions.
• The product being connected to an
unsuitable electricity supply.
• Accidental damage to or abuse or misuse
of the product including failure to use the
product for its normal intended purposes.
• The product modied, except by Dualit or
approved agent.
• Dismantling of or interference with the
product.
• Theft or attempted theft of the product.
• Operational misuse, wear and tear from
normal usage, incorrect adjustment and neglect.
• Incorrect installation, maintenance,
modication or unauthorised service work.
Before returning any product under this
Guarantee, please check that:
• You have followed the product instructions
correctly.
• The defect is not due to a blown fuse.
Please check and change the plug fuse.
• Your mains electricity supply is functional.
If you wish to claim under this Guarantee you
should:
• Send the product, postage or carriage paid,
to the dealer from whom it was purchased
or to Dualit direct.
• Ensure that the product is clean and
packed carefully (preferably in its original
carton).
• Enclose details of your name, address and
telephone number and when and where the
product was purchased, together with proof of
purchase (e.g. a till receipt).
• Please give exact details of the nature of the
defect.
This Guarantee does not cover any other
claims whatsoever, including, without
limitation, any liability for incidental, indirect
or consequential damage, nor does it cover
any claims for conversion or modication or
for the costs of repair carried out by any third
party without the prior consent of Dualit. If
replacement parts are tted to the product this
will not extend the period of the Guarantee.
For further advice contact the Dualit
customer helpline on [phone]
(09:00 to 17:00 Monday to Friday).
Alternatively, email Dualit at [email protected] or
visit www.dualit.com
TROUBLESHOOTING
*TO CONTACT CUSTOMER SERVICES, PLEASE EMAIL [email protected]
WITH YOUR MODEL AND SERIAL NUMBERS.
POSSIBLE CAUSE(S) SOLUTION(S)
MY TOASTER ISN’T WORKING
1. The toaster may not be plugged in. 1. Make sure the toaster is switched on and
plugged in correctly to the UK mains.
2. The Plug Fuse may need replacing. 2. The Plug Fuse may need replacing if the
Power Indicator does not turn on and the
device does not appear to work. Please check
and replace the Plug Fuse.
3. The thermal Fuse may need resetting. 3. Please contact Dualit customer services*for
help.
THE ELEMENTS CYCLE ON AND OFF
1. The toaster has a Thermostat which
constantly monitors the toaster’s running
temperature for perfect toast.
1. The elements will cycle on and off at certain
temperature to save energy and avoid over
cooked toast; no action is needed.
I GET UNEVEN TOASTING
1. The toaster has a Thermostat which
constantly monitors the toaster’s running
temperature for perfect toast.
1. If toasting bread rather than bagels, ensure
the toaster is set to the ‘TOAST’ setting on
the front panel. Please see page 11 for more
information.
2. The toaster may not be Fully Warm. 2. Allow the toaster to reach full temperature,
this should take 30 minutes depending on
conditions. See page 11.
3. Your bread may not be positioned on the
Conveyor correctly.
3. Check the edges of the bread are over the
elements and not off the edge of the conveyor.
4. The toasting setting you are using may not
be appropriate for the bread type.
4. Check the type of bread you are using is
appropriate for the toast setting your machine
is on; please see page 11.
5. ‘BAGEL’ setting or ‘STANDBY’ may be in
use.
5. Please check Function Control Dial is set to
‘TOAST’.
6. An element may have blown. 6. Check all elements glow when the toaster is
Fully Warm. If not contact Customer Services*
for help.
7. The fan may have stopped. 7. Check if the fan is audible when the
Conveyor Toaster is on and the green
‘READY’ light is illuminated. Ensure the fan
is clean as per instructions on page 13. If the
fan still appears to have stopped, contact
Customer Service*for help.
MY TOAST COMES OUT TOO LIGHT
1. The toast setting may be too low for the
type of bread you are using or the conditions
that you are using the toaster in.
1. Please see page 11 for information on
toasting settings for different bread types and
factors that affect toasting.

Dualit Limited County Oak Way Crawley West Sussex RH11 7ST
[phone] [email protected] www.dualit.com
GB-D
DON’T FORGET
TO REGISTER
YOUR PRODUCT
WWW. DUALIT.COM/REGISTER
OR BY POST
REGISTER YOUR PRODUCT
1. Fast and efficient customer service important safety advice, access
to manuals and product information should you require assistance with your
purchase.
2. A library of mouth-watering recipes and regular articles and blogs.
3. Be the first to hear about exciting new Dualit products.
Dualit recommends safety first: please register your product so that we
can contact you in the unlikely event that a safety notification is issued.
Remember to keep your receipt as proof of purchase.
POSSIBLE CAUSE(S) SOLUTION(S)
MY TOAST COMES OUT TOO LIGHT
2. Your Quick Start toast setting may be too
low.
2. If using Quick Start, you will need to turn the
toast setting up much higher than usual, then
dial it back as the toaster heats up. Please see
the table on page 11 for more information.
3. Your toaster is tted with a temperature
limiting Thermostat. During periods of
inactivity, longer than 5 minutes, the elements
will turn off (indicated by the red power
indicator going off).
3. Only introduce bread to the conveyor when
the red light is on and the elements are glowing
cherry red. See page 12 for details.
MY TOAST COMES OUT TOO DARK
1. The toast setting may be too high for the
type of bread you are using or the conditions
that you are using the toaster in.
1. Please see page 11 for information on
toasting settings for different bread types and
factors that affect toasting.
2. Quick Start setting may be too high or
is not decreasing enough as the Conveyor
Toaster continues to warm up.
2. See pages 10-11 for details. Monitor toast
colour and adjust toasting setting as toaster
warms up when using Quick Start.
3. Crumb Tray Bread Ramp does not fold
at.
3. This is a safety feature. The Bread Ramp is
designed not to fold at.