DualLite ELCTB Manual

Page 1/2 Rev. 06/08/20
DL_ELCTB_INST
Installation Instructions/User Manual
© 2020 Dual-Lite, a division of Hubbell Lighting, Inc. Specifications subject to change without notice • Printed in
the USA 701 Millennium Blvd • Greenville, SC 29607 / Website www.dual-lite.com
ELCTB
REMOTE TEST BUTTON
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
IMPORTANT SAFEGUARDS
SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
When using electrical equipment, basic safety precautions
should always be followed. Including the following:
• Do not use outdoors
• Do not let power supply cords touch hot surfaces
• Do not mount near gas or electrical heaters
• Equipment should be mounted in locations and at heights where it will not
be subjected to tampering by unauthorized personnel
• The use of accessory equipment not recommended by the manufacturer
may cause an unsafe condition
• Do not use this equipment for other than its intended use

Page 2/2 Rev. 06/08/20
DL_ELCTB_INST
Installation Instructions/User Manual
© 2020 Dual-Lite, a division of Hubbell Lighting, Inc. Specifications subject to change without notice • Printed in
the USA 701 Millennium Blvd • Greenville, SC 29607 / Website www.dual-lite.com
ELCTB
REMOTE TEST BUTTON
Only Install the ELCTB to the Class 2
"Remote Test Input" of an ELCR
The ELCTB Remote Test Button can be installed
directly to the ceiling or to a standard 4" round or 4"x4"
octagonal junction box.
1. Find the desired location for the center of the Test Button on the ceiling.
2. Cut or drill a hole at least 1 ½” but no larger than 2 ½”.
3. Feed ELCR Class 2 “Remote Test Input” wiring down through the hole.
a. These wires can be between 18 AWG and 24 AWG, solid or stranded.
b. If using stranded wire, twist the strands together.
4. Strip both wires at least ¼” and insert wires into the two designated
holes on the Test Button indicated by the arrows.
a. DO NOT install wires to the screws.
5. Push wires in until they are secured. For stranded wire, twist and push for
easier installation.
6. To verify wire connection to the board, gently tug on the wires and/or
visually inspect them.
7. Position Test Button over the hole and drive the #8 screws provided
directly into the ceiling.
1. Confirm the following characteristics of the junction box:
a. 4” round or 4” x 4” octagonal box
b. Cover plate holes accept #8 screws
c. Cover plate holes are 3 ½” apart
2. If this is an existing junction box, skip to Step 6.
3. Find the desired location for the center of the Test Button on the ceiling.
4. Cut or drill a 4” hole. DO NOT cut a 4” x 4” square hole.
5. Secure the junction box as specified by the manufacturer and the NEC.
6. Confirm that the largest gap distance of the hole is less than 4 2/3”. If it
is not, gaps will appear around the perimeter of the ELCTB after being
mounted.
7. Feed ELCR Class 2 “Remote Test Input” wiring into the junction box.
a. These wires can be between 18 AWG and 24 AWG, solid or stranded.
b. If using stranded wire, twist the strands together.
8. Strip both wires at least ¼” and insert wires into the two designated holes
on the Test Button indicated by the arrows.
a. DO NOT install wires to the screws.
9. Push wires in until they are secured. For stranded wire, twist and push for
easier installation.
10. To verify wire connection to the board, gently tug on the wires and/or
visually inspect them.
11. Position Test Button over the junction box and align the two ELCTB screw
holes with the cover plate screw holes
12. Drive the #8 screws provided directly into the junction box’s cover plate
screw holes.
MOUNTING DIRECTLY TO CEILING MOUNTING TO A JUNCTION BOX