Dukane 8952P User manual

1
Projector
8950P/8951P/8952P
User's Manual (detailed) – Operating Guide
Thank you for purchasing this projector.
►Before using this product, please read the "User's Manual -
Safety Guide" and related manuals to ensure the proper use of this product.
After reading them, store them in a safe place for future reference.
WARNING
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
NOTE
Trademark acknowledgment
Various symbols are used in this manual. The meanings of these symbols are
described below.
About this manual
About this manual
WARNING
CAUTION
This entry warns of a risk of serious personal injury or even
death.
This entry warns of a risk of personal injury or physical damage.
Please refer to the pages written following this symbol.


• Windows®is a registered trademark of Microsoft Corporation in the U.S. and/or
other countries.
• VESA and DDC are trademarks of the Video Electronics Standard Association.
• Mac®is a registered trademark of Apple Inc.
• DVI is a trademark of Digital Display Working Group.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing LLC.
• Trademark PJLink is a trademark applied
for trademark rights in Japan, the United
States of America and other countries and areas.
All other trademarks are the properties of their respective owners.
NOTICE This entry notices of fear of causing trouble.

2
Contents
Contents
Contents
About this manual. . . . . . . . . . . 1
Contents . . . . . . . . . . . . . . . . . . 2
Introduction . . . . . . . . . . . . . . . 3
Projector features . . . . . . . . . . . . . . . 3
Important safety instruction (for the
moving) . . . . . . . . . . . . . . . . . . . . . . . 3
Checking the contents of package . . 4
Attaching the lens unit. . . . . . . . . . . . 4
Part names . . . . . . . . . . . . . . . . 5
Projector . . . . . . . . . . . . . . . . . . . . . . 5
Control panel. . . . . . . . . . . . . . . . . . . 6
Indicator lamp . . . . . . . . . . . . . . . . . . 6
Rear panel . . . . . . . . . . . . . . . . . . . . 6
Remote control . . . . . . . . . . . . . . . . . 7
Setting up . . . . . . . . . . . . . . . . . 8
Installation environment . . . . . . . . . . 8
Projection style . . . . . . . . . . . . . . . . . 8
Projection distance . . . . . . . . . . . . . . 9
Placement . . . . . . . . . . . . . . . . . . . . 10
Supplementary anti-theft means . . . 10
Connecting with your devices . . . . . 11
Connecting power supply . . . . . . . . 15
Remote control . . . . . . . . . . . . 16
Putting batteries . . . . . . . . . . . . . . . 16
Transmitting condition. . . . . . . . . . . 17
Changing the frequency of remote
control signal. . . . . . . . . . . . . . . . . . 17
Using the REMOTE ID function . . . 18
Using as a wired remote control . . . 18
Laser pointer . . . . . . . . . . . . . . . . . . 18
Operating . . . . . . . . . . . . . . . . 19
Turning on. . . . . . . . . . . . . . . . . . . . 19
Turning off . . . . . . . . . . . . . . . . . . . . 20
Using the elevator feet . . . . . . . . . . 20
Using the functions for the lens. . . . 21
Displaying and switching the image 22
Selecting an aspect ratio. . . . . . . . . 23
Using the automatic adjustment feature . . 23
Adjusting the position . . . . . . . . . . . 24
Correcting the keystone distortion . . . 24
Using the magnify feature . . . . . . . . 25
Temporarily freezing the screen . . . 25
Temporarily blanking the screen . . . 26
Temporarily shutting the screen . . . 26
P by P (Picture by Picture) . . . . . . . 27
Using the menu function . . . . . . . . 28


EASY MENU. . . . . . . . . . . . . . . 29
ASPECT, AUTO KEYSTONE,
KEYSTONE,
KEYSTONE
,
PICTURE MODE, ECO MODE,
MIRROR, RESET, FILTER TIME, LANGUAGE,
ADVANCED MENU, EXIT
PICTURE menu . . . . . . . . . . . . 31
BRIGHTNESS, CONTRAST, GAMMA, COLOR TEMP,
COLOR, TINT, SHARPNESS, ACTIVE IRIS, MYMEMORY
IMAGE menu . . . . . . . . . . . . . . 34
ASPECT, OVER SCAN, V POSITION, H POSITION,
H PHASE, H SIZE, AUTO ADJUST EXECUTE
INPUT menu . . . . . . . . . . . . . . 36
PROGRESSIVE, VIDEO NR, 3D-YCS, COLOR
SPACE, COMPONENT, VIDEO FORMAT, DIGITAL
FOMAT, DIGITAL RANGE, COMPUTER IN, FRAME
LOCK, RESOLUTION
SETUP menu . . . . . . . . . . . . . . 40
AUTO KEYSTONE, KEYSTONE, KEYSTONE ,
ECO MODE, MIRROR, MONITOR OUT
SCREEN menu. . . . . . . . . . . . . 42
LANGUAGE, MENU POSITION, BLANK, START UP,
MyScreen,MyScreen Lock, MESSAGE, SOURCE
NAME,TEMPLATE, C.C.
OPTION menu . . . . . . . . . . . . . 47
SOURCE SKIP, AUTO SEARCH, AUTO KEYSTONE ,
DIRECT ON, AUTO OFF, SUTTER TIMER LAMP
TIME, FILTER TIME, MYBUTTON, MYSOURCE,
SERVICE
NETWORK menu . . . . . . . . . . . 56
SETUP, PROJECTOR NAME,
MYIMAGE,
INFORMATION, SERVICE
SECURITY menu . . . . . . . . . . . 61
ENTER PASSWORD, SECURITY PASSWORD,
MyScreen PASSWORD, PIN LOCK, TRANSITION
DETECTOR, MYTEXT PASSWORD, MYTEXT
DISPLAY, MYTEXT WRITING
Maintenance . . . . . . . . . . . . . . 67
Lamp unit . . . . . . . . . . . . . . . . . . . . 67
Filter unit . . . . . . . . . . . . . . . . . . . . . 69
Internal clock battery. . . . . . . . . . . . 70
Others . . . . . . . . . . . . . . . . . . . . . . . 70
Troubleshooting . . . . . . . . . . . 71
Related messages . . . . . . . . . . . . . 71
Regarding the indicator lamps . . . . 72
Phenomena that may be easily
mistaken for machine defects . . . . . . 74
Warranty and after-service. . . 77
Specifications . . . . . . . . . . . . . 77



3
Introduction
This projector has a capability to project various picture signals onto a screen. This
projector requires only a minimal amount of space for installation and can produce
a large projected image from even a short distance. Moreover, the projector has the
following features to extend its potentiality for broad use.
The
HDMI
HDMI port can support various image equipment which have digital
interface to get clearer pictures on a screen.
 The super bright lamp and high quality optical system can fulfill the demands
of professional uses.
 The selectable optional lens units and the super wide range of the lens shift
feature will give much more chances to install the product wherever you
want.
 The lens shutter can hide your inside operations and will help your
presentation.
 The wealth of I/O ports is believed to support any business scene.
 This projector's network supports the PJLinkTM standard.
 PJLinkTM is a unified standard for operating and controlling data projectors.
PJLinkTM enables central control of projectors manufactured by different
vendors and projectors can be operated by a controller. PJLinkTM compliant
equipment can be managed and controlled at any time and in any place,
regardless of manufacturer.
For the command of PJLinkTM, see

 User's Manual (Technical)
For specifications of PJLinkTM, see the web site of the Japan Business
Machine and Information System Industries Association.
URL: http://pjlink.jbmia.or.jp
 The unique Electric Dust Catcher Air filter system is expected to prevent
air dust from getting into the projector and offers you less maintenance
frequency.
Projector features
Introduction
Introduction
Important safety instruction (for moving)
*For details, see the

 User's Manual (concise) or Safety Guide.
►Always move the projector
with two or more people. Place your hands in the
dented parts on the bottom of the projector when
carrying the projector.
►Remove all the attachments including the power
cord and cables, from the projector when carrying
the projector.
WARNING
Dented parts

4
Introduction
(1) Projector
(2) Lens adapter
(3) Hexagon wrench (for installation of
the optional lens unit)
(4) Power cord
(5) Computer cable
(6) Remote control
with two batteries
(7) User’s manuals (a book and a CD)
(8) Security label
Soon after purchasing this product, check that all the following items are included in
the package. If any items should be missing, tell your dealer immediately.
►Use only the lens unit specified by the manufacturer.
►Leave both attaching and removing the lens unit to the service personnel your
dealer sent.
►Read and keep the user’s manual of the lens unit.
►Use special caution not to drop the lens unit or knock it against something.
►Do not transport the projector to which the lens unit is attached.
WARNING
Keep the original packing materials for the lens unit, and use
them correctly when transporting or storing the lens unit.
CAUTION
►Do not touch the lens surface directly.
►Keep the dust protector of the projector, and use it while no lens unit is
attached to the projector.
NOTICE
• This product is supplied without a lens unit so that you can choose
from a range of lenses (

 77) that can meet your requirements. Ask your dealer
about details, and prepare one or more lens unit together with this product.
• Some additional accessories or services may be required for your use. We
recommend consult with your dealer beforehand.
NOTE
►Keep the original packing materials, and use them correctly
when transporting or storing the product.
CAUTION
Request your dealer to install the lens unit in the projector. Be sure to leave both
removing and attaching the lens unit to the service personnel your dealer sent.
(1) (2)
(3)
(8)
(4)
(7)
(6)(5) BLANK LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON COMPUTER
LENS SHIFT
KEYSTONE
ID 3
ID 4
ID 2
ID 1
VIDEO
AUTO
ASPECT
RESET
MENU
MAGNIFY
ON
OFF
3
4
ENTER
FOCUS
+
-
POSITION
PbyP
ZOOM
+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER
Checking the contents of package
Attaching the lens unit

5
Part names
Part names
Part names
Projector
(1) Dust protector
(2) Remote sensors (x 2) (

 17)
(3) Exhaust vents
(4) Filter cover (

 69)
The filter unit and intake vent are
inside.
(5) Control panel (

 6)
(6) Rear panel (

 6)
(7) Shutdown switch (

 73)
(8) Lamp cover (

 67)
The lamp unit is inside.
(9)
AC IN
AC IN (AC inlet) (

 15)
(10) Power switch (

 19,20)
(11) Security bar (

 10)
(12) Security slot (

 10)
(13) Dented part (x 2) (

 3)
(14) Elevator feet (x 2) (

 20)
►HOT! : Do not touch around the lamp cover or the exhaust
vents during use or just after use, since it is hot.
►Do not look into the lens or vents while the lamp is on, since the strong light is
not good for your eyes.
►Do not grab the front cover or front ring to hold the projector, since you can
drop the projector.
►Do not handle the elevator feet without holding the projector, since the
projector may drop down.
WARNING
►Maintain normal ventilation to prevent the projector from
heating up. Do not cover, block or plug up the vents. Do not place anything that
can stick or be sucked to the vents, around the intake vents. Clean the air filter
periodically.
CAUTION
(2)
(3)
(8)
(10)
(9)
(12)
(14)
(4)
HOT!
(7)
(6) (5)
(13)
(11)
(1) HOT!
See the NOTICE
►Do not touch the lens surface directly.
►Keep the dust protector of the projector, and use it when no lens unit is
attached to the projector.
NOTICE
Front ring
Front cover

6
Part names
STANDBY/ON
MENU
LENS SHIFT
COMPUTER
ZOOM
VIDEO
FOCUS
DIGITAL
SHUTTER
I O
HDMI DVI-D
CONTROL IN CONTROL OUT REMOTE
CONTROL
IN
OUT
S-VIDEO
COMPUTER IN2
COMPUTER IN1
VIDEO 1 BNC
R/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2
Y
Cb/Pb
Cr/Pr
AC IN
LAN
MONITOR
OUT
Control panel
(1)
STANDBY/ON
STANDBY/ON button (

 19,20)
(2) Cursor buttons ( ▲/▼/◄/►) (

 28)
(3)
MENU
MENU button (

 28)
(4)
COMPUTER
COMPUTER button (

 22)
(5)
VIDEO
VIDEO button (

 22)
(6)
DIGITAL
DIGITAL button (

 22)
(7)
LENS SHIFT
LENS SHIFT button (

 21)
(8)
ZOOM
ZOOM button (

 21)
(9)
FOCUS
FOCUS button (

 21)
(10)
SHUTTER
SHUTTER button (

 26)
Rear panel(

 10)
(1)
HDMI
HDMI port
(2)
DVI-D
DVI-D port
(3)
LAN
LAN port
(4)
MONITOR OUT
MONITOR OUT port
(5)
CONTROL IN
CONTROL IN port
(6)
CONTROL OUT
CONTROL OUT port
(7)
REMOTE CONTROL IN
REMOTE CONTROL IN port
(8)
REMOTE CONTROL OUT
REMOTE CONTROL OUT port
(9)
S-VIDEO
S-VIDEO port
(10)
VIDEO 1
VIDEO 1 port
(11)
VIDEO 2
VIDEO 2 port
(12)
COMPUTER IN1
COMPUTER IN1 port
(13)
COMPUTER IN2
COMPUTER IN2 port
(14)
BNC (G/Y, B/Cb
BNC (G/Y, B/Cb
/Pb
/Pb
, R/Cr
, R/Cr
/Pr
/Pr
, H, V)
, H, V) ports
(15) Component
(Y, Cb
(Y, Cb
/Pb
/Pb
, Cr
, Cr
/Pr
/Pr
)
) ports
(6)
(5)
(4)
(1)
(2)
(3)
►Use the shutdown switch only when the projector is not turned
off following the normal procedure, since pushing this switch stops operation of
the projector without cooling it down.
CAUTION
(1)
Indicator lamp (

 72)
(1)
POWER
POWER indicator
(2)
TEMP
TEMP indicator
(3)
LAMP
LAMP indicator
(4)
SECURITY
SECURITY indicator
(5)
SHUTTER
SHUTTER indicator
SHUTTERPOWER TEMP LAMP SECURITY
(9)
(8)
(7)
(10)
(1) (2) (3) (4) (5)
(2) (4)
(8)(7)(6)(5)
(3) (9)(10)(11)
(13)(12)(14)(15)
The indicator
will light in
green while
the menu of
the function is
displayed.
The
indicator of
group the
selected
input port
belongs to
will light in
green.
The indicator will blink in yellow
while the lens shutter is closed.

7
Part names
Remote control
(1) Laser pointer (

 18)
It is a beam outlet.
(2)
LASER INDICATOR
LASER INDICATOR (

 18)
(3)
LASER
LASER button (

 18)
(4)
STANDBY/ON
STANDBY/ON button (

 19,20)
(5)
ID
ID (
1-4
1-4) button (

 18)
(6)
COMPUTER
COMPUTER button (

 22)
(7)
VIDEO
VIDEO button (

 22)
(8)
DIGITAL
DIGITAL button (

 22)
(9)
MY SOURCE
MY SOURCE button (

 22)
(10)
LENS SHIFT
LENS SHIFT button (

 21)
(11)
ZOOM +/-
ZOOM +/- button (

 21)
(12)
FOCUS +/-
FOCUS +/- button (

 21)
(13)
AUTO
AUTO button (

 23)
(14)
POSITION
POSITION button (

 24)
(15)
ASPECT
ASPECT button (

 23)
(16)
KEYSTONE
KEYSTONE button (

 24)
(17)
MAGNIFY ON/OFF
MAGNIFY ON/OFF button (

 25)
(18)
FREEZE
FREEZE button (

 25)
(19)
BLANK
BLANK button (

 26)
(20)
SHUTTER
SHUTTER button (

 26)
(21)
MY BUTTON
MY BUTTON (
1-4
1-4) button (

 49)
(22)
P by P
P by P button (

 27)
(23)
MENU
MENU button (

 28)
(24)
ENTER
ENTER button : press the center point.
Cursor button: press the point ▲/▼/◄/►(

 28).
(25)
RESET
RESET button (

 28)
(26) Wired remote control port (

 18)
(27) Battery cover (

 16)
(28) Battery holder (

 16)
(29) Frequency switch (

 17)
►Do not look into the beam outlet or
point the beam at people or pets while pressing the
LASER
LASER button, since the beam is not good for eyes.
WARNING
►Note that the laser beam may result
in hazardous radiation exposure. Use the laser pointer
only for pointing on the screen.
CAUTION
BLANK LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON COMPUTER
LENS SHIFT
KEYSTONE
ID 3
ID 4
ID 2
ID 1
VIDEO
AUTO
ASPECT
RESET
MENU
MAGNIFY
ON
OFF
3
4
ENTER
FOCUS
+
-
POSITION
PbyP
ZOOM
+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER
(4)
(2)
(1)
(3)
Back of
the remote control
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
(20)
(21)
(22)
(23)
(24)
(25)
(26)
(27)
(28)
(29)

8
Setting up
Setting up
Setting up
Read this chapter through first. Then install the projector into place.
►Do not place the product on an unstable surface such as an
uneven, tilted, or vibrating place.
►Do not place the product near water - for example, near a bathtub, washbowl,
kitchen sink, or laundry tub; in a wet basement, near a swimming pool, beach; or
outdoors.
WARNING
►Do not place the product in a dusty, smoky, or humid place -
for example, on a passage, in a smoking space, in a kitchen, or outdoors.
►Do not place the product near heat sources - for example, radiators, heat
registers, stoves, or other product (including amplifiers) that produces heat.
►Do not place this product in a magnetic field.
CAUTION
Installation environment
This product requires an installing place that is stable, cool and airy. Check your
installation environment in accordance with the following.
►Do not place the product in a place where radio interference may
be caused.
►Do not place the projector in a place where any strong lights hit the remote
sensors.
NOTICE
Projection style
This projector can be used by the following projection styles. Choose the style
suitable to your use.
(1) Standard style
(placed on a table)
(2) Ceiling mount
(suspended from a ceiling)
• In the case of ceiling mount, upward projection, or downward
projection, the specified mounting accessories (

 77) and service are required
to install the projector. Request them from your dealer. Ask your dealer for
installation other than styles above.
NOTE
►Consult with your dealer about installation beforehand.
►Use only the mounting accessories the manufacturer specified, and leave
installing and removing the projector with the mounting accessories to the
service personnel.
WARNING

9
Setting up
Projection distance
Refer to the following to arrange the projector and your screen. The values shown in the
following table were calculated for the model 8950Pwith the standard lens unit SD-
804. See the user’s manual of your lens unit for your case. The values differ for every
combination of the projector and the lens unit.
(a) Screen
size
[inch (m)]
4 : 3 screen 16 : 9 screen
(b) Projection distance
[m (inch)]
(c) Screen height
[cm (inch)]
(b) Projection distance
[m (inch)]
(c) Screen height
[cm (inch)]
min. max. down up min. max. down up
40 (1.0) 1.7 (66) 2.3 (89)
-23 (-9)
84 (33) 1.3 (53) 1.8 (72) -33 (-13) 83 (33)
60 (1.5) 2.6 (103) 3.5 (136)
-34 (-13) 125 (49)
2.1 (83) 2.8 (110) -49 (-19) 124 (49)
70 (1.8) 3.1 (121) 4.0 (159)
-40 (-16)
146 (58) 2.5 (98) 3.3 (129) -58 (-23) 145 (57)
80 (2.0) 3.5 (139) 4.6 (183)
-45 (-18)
167 (66) 2.9 (112) 3.8 (148) -66 (-26) 165 (65)
90 (2.3) 4.0 (157) 5.2 (206)
-51 (-20)
188 (74) 3.2 (127) 4.3 (168) -74 (-29) 186 (73)
100 (2.5) 4.4 (175 5.8 (230)
-56 (-22)
209 (82) 3.6 (142) 4.7 (187) -82 (-32) 207 (81)
120 (3.0) 5.4 (211 7.0 (277)
-68 (-27)
251 (99) 4.4 (172) 5.7 (225) -99 (-39) 248 (98)
150 (3.8) 6.7 (266 8.8 (347)
-85 (-33)
313 (123) 5.5 (216) 7.2 (283) -123 (-49) 310 (122)
200 (5.1) 9.0 (356 11.8 (464)
-113 (-44)
418 (164) 7.4 (290) 9.6 (379) -164 (-65) 414 (163)
250 (6.4) 11.3 (447 14.8 (582)
-141 (-56)
522 (206) 9.2 (364) 12.0 (474) -206 (-81) 517 (204)
300 (7.6) 13.6 (537 17.8 (699)
-169 (-67)
627 (247) 11.1 (438) 14.5 (570) -247 (-97) 620 (244)
350 (8.9) 15.9 (628 20.7 (816)
-198 (-78)
731 (288) 13.0 (512) 16.9 (666) -288 (-113) 724 (285)
400 (10.2) 18.2 (718 23.7 (934)
-226 (-89)
835 (329) 14.9 (586) 19.4 (762) -329 (-130) 827 (326)
500 (12.7) 22.8 (899 29.7 (1168)
-282 (-111)
1044 (411) 18.6 (734) 24.2 (954) -411 (-162) 1034 (407)
600 (15.2) 27.4 (1081 35.6 (1403)
-339 (-133)
1253 (493) 22.4 (882) 29.1 (1145) -493 (-194) 1241 (488)
700 (17.8) 32.0 (1262 41.6 (1638)
-395 (-156)
1462 (576) 26.2 (1030) 34.0 (1337) -576 (-227) 1447 (570)
(a)
(b)
(c) up
(c) down
* The values shown in the table are calculated for a full size screen: 1024×768
(a) Screen size (diagonal)
(b) Projection distance (±10%)
(c) Screen height (±10%), when the vertical lens shift is set full upward.
Projector top
Projector bottom
(Installation side)
►Do not use a polarized screen, since it can cause a red image.NOTICE

10
Setting up
Supplementary anti-theft means
This projector has the security bar for a commercial
anti-theft chain or wire up to 10 mm in diameter, and
also the security slot for the Kensington lock.
For details, see the manual of your security tool.
►Do not use the security slot to
prevent the projector from falling down, since it is not
designed for it.
WARNING
• These are not provided as comprehensive theft
preventions but supplemental measures.
NOTE
Security slot
Anti-theft chain or wire
Security bar
►Keep the projector away from anything that is easy to catch
fire.
►Do not block or cover the openings on the projector, and keep sufficiently
space for ventilation around the projector.
• Do not use the projector on a cushiony surface such a rug, a carpet or bedding.
• Keep the projector away from any light materials such as a piece of paper that
can stick to the intake holes.
►Do not use the projector on an unstable stand such as a cart.
►Place the projector so that nothing enters to the inside of the projector.
• Keep the projector away from any small things such as paperclips that can fall
into the inside.
• Keep the projector away from any liquids that can spill or leak into the product.
WARNING
►Keep the projector away from anything that is heat conductive
such as metal.
• Do not use the projector on a metallic table.
►Keep the projector away from anything that is weak in heat such as some kinds
of plastics.
CAUTION
►Place the projector so that there is nothing that blocks the
projection light to the screen.
►Avoid exposing directly the remote sensor to any strong lights.
NOTICE
Placement
►Do not place the anti-theft chain
or wire near the projector’s exhaust vents, since the
chain or wire heated by the hot exhaust gas may
cause burns.
CAUTION
In placing the projector in place in accordance with the preceding section
"Projection distance" (

 9) heed the following too.

11
Setting up
Connecting with your devices
Before connecting the projector to your devices, check the manual of the device in
order to make sure that the device is suitable to connect with this projector and to
check what is required for the connection.
Consult your dealer when the required accessory did not come with the product or
the accessory is damaged. It may be regulated under some standard.
►Use only the accessories specified or recommended by
manufacturer. Modify neither a projector nor accessories.
►Do not connect or disconnect the projector with devices while they are
connected to a power supply except for the cases directed by the manuals of
devices.
WARNING
►Some connecting cable may have to have a specific length,
or a ferrite core at the end to connect to the projector, under the regulation of
electro-magnetic interference. When a ferrite core is attached to the specified
cable only at one end, connect to the projector the end that the ferrite core is
attached at.
►Be careful not to set a connector into a wrong port or with a wrong way.
►Be careful not to damage the cables. Route the cables not to be stepped on
and pinched out.
CAUTION
(continued on next page)
• For this product, the optional cable cover is ready to be purchased. To
place an order for it, please tell your dealer the type name of it (

 77).
NOTE
After making sure that the projector and the devices are turned off, perform
the connection, according to the following instructions. Refer to the figures in
subsequent pages.
►Do not turn your device on prior to the projector, except for the
cases directed by the manuals of devices.
NOTICE

12
Setting up
Control from the computer
HDMI REMOTE
CONTROL
LAN
DVI-D
CONTROL IN CONTROL OUT
IN
OUT
S-VIDEO
VIDEO 1
COMPUTER IN1 COMPUTER IN2
MONITOR
OUT
BNC
VIDEO 2
R/Cr/Pr G/Y B/Cb/Pb H V
Y
Cb/Pb
Cr/Pr
K
HDMI
S-VIDEO
OUT VIDEO
OUT
COMPONENT
Y Cb/Pb Cr/Pr
VIDEO
OUT
(continued on next page)
Connecting your devices (continued)
Example of connecting with VCR or DVD players
HDMI REMOTE
CONTROL
LAN
DVI-D
CONTROL IN CONTROL OUT
IN
OUT
S-VIDEO
VIDEO 1
COMPUTER IN1 COMPUTER IN2
MONITOR
OUT
BNC
VIDEO 2
R/Cr/Pr G/Y B/Cb/Pb H V
Y
Cb/Pb
Cr/Pr
K
DVI-D
RS-232C RGB OUT RGB OUT RGB OUT
LAN
Example of connecting with computers
►For safety,
do not connect the
LAN
LAN port
to any network that might
have excessive voltage.
CAUTION
Digital signal input
Video signal input
Computer signal input

13
Setting up
Connecting your devices (continued)
Example of connecting with another projector or a display device
HDMI REMOTE
CONTROL
LAN
DVI-D
CONTROL IN CONTROL OUT
IN
OUT
S-VIDEO
VIDEO 1
COMPUTER IN1 COMPUTER IN2
MONITOR
OUT
BNC
VIDEO 2
R/Cr/Pr G/Y B/Cb/Pb H V
Y
Cb/Pb
Cr/Pr
K
RS-232C RGB OUT
BLANK LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON COMPUTER
LENSSHIFT
KEYSTONE
ID3
ID4
ID2
ID1
VIDEO
AUTO
ASPECT
RESET
MENU
MAGNIFY
ON
OFF
3
4
ENTER
FOCUS
+
-
POSITION
PbyP
ZOOM
+
-
1
2
MYBUTTON
MYSOURCE
SHUTTER
REMOTE
CONTROL IN
RS-232C RGB IN
Control from the computer
Redirection
of an RGB input
to another display
Simultaneous remote control
of another projector
Control of
another device by
RS-232C commands
Computer signal input
Wired
remote
control

14
Setting up
Connecting your devices (continued)
• Be sure to read the manuals for devices before connecting them to the projector,
and make sure that all the devices are suitable to be connected with this product.
• Before connecting to a PC, check the signal level, the signal timing, and the resolution.
- Be sure to consult to the administrator of the network. Do not connect
LAN
LAN port to any
network that might have excessive voltage.
- Some signal may need an adapter to input this projector.
- Some PCs have multiple screen display modes that may include some signals which
are not supported by this projector.
-
Although the projector can display signals with resolution up to UXGA (1600X1200), the signal will be
converted to the projector’s panel resolution before being displayed. The best display performance
will be achieved if the resolutions of the input signal and the projector panel are identical.
• While connecting, make sure that the shape of the cable's connector fits the port to
connect with. And be sure to tighten the screws on connectors with screws.
• When connecting a laptop PC to the projector, be sure to activate the PC’s external
RGB output. (Set the laptop PC to CRT display or to simultaneous LCD and CRT
display.) For details on how this is done, please refer to the instruction manual of the
corresponding laptop PC.
• When the picture resolution is changed on a computer depending on an input,
automatic adjustment function may take some time and may not be completed. In this
case, you may not be able to see a check box to select “Yes/No” for the new resolution
on Windows. Then the resolution will go back to the original. It might be recommended
to use other CRT or LCD monitors to change the resolution.
• In some cases, this projector may not display a proper picture or display any picture on
screen. For example, automatic adjustment may not function correctly with some input
signals. An input signal of composite sync or sync on G may confuse this projector, so
the projector may not display a proper picture.
•
The
HDMI
HDMI and
DVI-D
DVI-D ports of this model are compatible with HDCP (High-bandwidth Digital Content
Protection) and therefore capable of displaying a video signal from HDCP compatible DVD players or the like.
NOTE
About Plug-and-Play capability
Plug-and-Play is a system composed of a computer, its operating system and peripheral
equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-and-
Play can be used by connecting this projector to a computer that is VESA DDC (display
data channel) compatible.
•
Take advantage of this feature by connecting an RGB cable to the
COMPUTER IN1
COMPUTER IN1 port
(DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is
attempted.
• Please use the standard drivers in your computer as this projector is a Plug-and-Play monitor.
NOTE for HDMI
• The
HDMI
HDMI supports the following signals.
-
Video signal : 480i@60,480p@60,576i@50, 576p@50,720p@50/60,1080i@50/60,10
80p@50/60
-PC signals : See User’s Manual (detailed) Technical
• This projector can be connected with another equipment that has HDMI or DVI
connector, but with some equipment the projector may not work properly, something like
no video.
• Be sure to use an HDMI cable that has the HDMI logo.
•
When the projector is connected with a device having DVI connector, use a DVI to HDMI cable
to connect with the
HDMI
HDMI input.

15
Setting up
Connecting power supply
1. Make sure that the power switch of the projector is set to the off-position
(marked with “
O
O”).
2. Insert the socket end of the power cord into the
AC IN
AC IN (AC inlet) of the
projector.
►Do not connect the projector to a power supply when the lens
unit is not attached.
►Use this projector from only the specified power supply in accordance with the
label indication on the projector.
►Use a power outlet that is close to the projector and easily accessible.
►Do not overload the outlet, since overloading can result in a fire or an electric
shock.
►Use only the power cord that came with this product and is suitable for your
power supply. If the suitable power cord did not come with this product, consult
your dealer.
►Do not use a damaged power cord. If the power cord you need is damaged,
ask your dealer for a new power cord of the same type.
►Do not handle the power cord with wet hands.
►Do not repair or modify the power cord.
►Be careful not to damage the power cord. Route the power cord so that it is
not likely to be walked on or pinched by items placed upon or against them.
►Connect firmly the power cord not to result in loose connection. Do not use a
loose or unsound power outlet.
WARNING
AC IN
AC IN
Socket of the power cord
In accordance with the warnings shown below, connect the AC inlet of the
projector to the proper power outlet. The following walks you through the
connection.
3. Plug the other end of the power cord into the power outlet.
Power switch

16
Remote control
Remote control
Remote control
Putting batteries
The remote control needs the two batteries of the following type.
1. Remove the battery cover in the back of the
remote control. Push lightly the knob of the
battery cover while pulling it up.
2.
Put the batteries into the battery holder, according to the
polarity markings “+” and “-“ inside the holder.
3.
Put the battery cover back into place until it clicks.
►Be careful not to press the
LASER
LASER button when loading the
batteries. It is dangerous if a laser beam is unintentionally turned on. Please
refer to the section "Laser pointer" (

 18).
►Be careful of handling batteries, since a battery can cause explosion, cracking
or leakage that could result in a fire, injury, or environment pollution.
• Use only the specified batteries. Do not use batteries of different types.
• When replacing, replace both of the batteries with new batteries of the same
type. Do not use a new battery with a used battery.
• Do not use a battery with damage, such as scratches, dents, rust or leakage.
• Make sure the plus and minus terminals are correctly aligned when loading a
battery.
• Do not work on a battery; for example recharging or soldering.
• If the remote control is not used for a long period of time, remove the batteries.
• Keep batteries in a dark, cool and dry place. Never expose a battery to a fire or
water.
• Keep batteries away from children and pets.
• When a battery leaked, wipe the leakage out well with a waste cloth. If the
leakage adhered to your body, immediately rinse it well with water. When a
battery leaked in the battery holder, replace the batteries after wiping the leakage
out.
• Obey the local laws on disposing a battery.
WARNING
HITACHI MAXELL, part number LR6 or R6P
The batteries that came with the product are a type suitable to this remote control.
The following walks you through loading batteries into the remote control.
• If the remote control malfunctions, try replacing the batteries with
fresh ones.
NOTE

17
Remote control
BLANK LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON COMPUTER
LENSSHIFT
KEYSTONE
ID3
ID4
ID2
ID1
VIDEO
AUTO
ASPECT
RESET
MENU
MAGNIFY
ON
OFF
3
4
ENTER
FOCUS
+
-
POSITION
PbyP
ZOOM
+
-
1
2
MYBUTTON
MYSOURCE
SHUTTER
Transmitting condition
The remote control works with the remote
sensors on the projector using infrared light
(Class 1 LED). The remote sensor senses the
remote control signals reached into the range
within 60 degrees (to right and left) and 3 meters
about from the sensor.
30º 30º Approx.
3 m
Remote
sensor
Remote
sensors
• You can inactivate one or two sensors from the three sensors using
the item REMOTE RECEIVE. of the SERVICE menu under the OPTION menu.
• When you want to use two or more projectors of this type at the same time
and the same place, utilize the REMOTE ID function. The buttons of
ID 1
ID 1,
ID 2
ID 2,
ID 3
ID 3 and
ID 4
ID 4 on the remote control can name the projector given the same ID
number as the button by the item REMOTE ID of the SERVICE menu under the
OPTION menu.
NOTE
►Avoid exposing directly the remote sensor to any strong lights.
►Do not put anything between the remote control and the remote sensor on the
projector, since it may interfere with transmission of the remote control signals.
NOTICE
Changing the frequency of remote control signal
The accessory remote control has the choice of
mode 1 or mode 2, in the frequency of its signal.
If the remote control does not function properly,
attempt to change the signal frequency.
Please remember that the “REMOTE FREQ.” in
SERVICE item of OPTION menu (

 51) of the
projector to be controlled should be set to the
same mode as the remote control.
To set the mode of the remote control, slide the
knob of the frequency switch inside the battery
cover into the position indicated by the mode
number to choose.
2 1
Back of the
remote control
Inside of
the battery cover
Frequency switch

18
Remote control
BLANK LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON COMPUTER
LENS SHIFT
KEYSTONE
ID 3
ID 4
ID 2
ID 1
VIDEO
AUTO
ASPECT
RESET
MENU
MAGNIFY
ON
OFF
3
4
ENTER
FOCUS
+
-
POSITION
PbyP
ZOOM
+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER
Using as a wired remote control
The accessory remote control works as a wired remote control,
when the wired control port at the bottom of the remote control
connects with the
REMOTE CONTROL
REMOTE CONTROL port on the back of the
projector via an audio cable with 3.5 diameter stereo mini plugs.
This function is useful when a wireless remote signal
may not reliably reach the projector.
• To connect the remote control with the projector, use an audio cable
with 3.5 diameter stereo mini plugs.
NOTE
MI DVI
-
D
CONTROL IN CONTROL OUT REMOTE
CONTROL
IN
OUT
S-VIDEO
COMPUTER
VIDEO 1 BNC
R/Cr/Pr G/Y B/Cb/Pb H
Y
Cb/Pb
Cr/Pr
MONITOR
OUT
BLANK LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON COMPUTER
LENSSHIFT
KEYSTONE
ID3
ID4
ID2
ID1
VIDEO
AUTO
ASPECT
RESET
MENU
MAGNIFY
ON
OFF
3
4
ENTER
FOCUS
+
-
POSITION
PbyP
ZOOM
+
-
1
2
MYBUTTON
MYSOURCE
SHUTTER
Laser pointer
This remote control has a laser pointer in place of a finger or rod. The laser beam
works and the
LASER INDICATOR
LASER INDICATOR lights while the
LASER
LASER button is pressed.
►Use the laser beam of the remote control only for the pointer
on the screen. Do not apply the laser beam to anything except the screen.
• Never hit eyes by the laser beam since the laser beam can injure eyes.
• Do not apply the laser beam to anything except the screen.
WARNING
LASER INDICATOR
LASER INDICATOR
LASER
LASER button
Laser aperture
Using the REMOTE ID function
This is the function to define which projector is controlled by the remote control. Utilize
this function when you use some projectors of the same type at the same time.
1. Set the ID number to the projector beforehand,
referring to the item “REMOTE ID” item (

 52).
2.
Press a ID button on the remote control. The ID button
selected will light for 3 seconds.
• Each time you press any button (except ID buttons), the ID button of
current selected ID number will light.
• To confirm the projector's current ID, press any ID button for 3 seconds. Its
number will be shown on each screen regardless of set ID of projector.
NOTE
DIGITAL
ID 3
ID 4
ID 2
ID 1
VIDEO

19
Operating
1. Make sure that the power cord is firmly and
correctly connected to the projector and the outlet.
2. Press down the side marked “
I
I” on the power
switch.
The
POWER
POWER indicator will light up in steady
orange.
Then wait for the buttons to become ready. It may
take several seconds .
3. Press the
STANDBY/ON
STANDBY/ON button (on the projector
or the remote control).
The projection lamp will light up and the
POWER
POWER
indicator will begin blinking in green. When the
power is completely on, the indicator will stop
blinking and light in steady green.
To display the picture, select an input signal according to the section "Displaying
and switching the image" (

 22).
Turning on
The following walks you through the steps to turn the projector on. For other
devices, follow the manual of each.
• When the item DIRECT ON of the OPTION menu is set to the ON,
and that the projector was turned off by only the power switch without using
the
STANDBY/ON
STANDBY/ON button, switching the power switch on turns the projector on
without the formal procedure shown above.
NOTE
►Do not look directly into the lens or the openings on the
projector while the lamp is on.
►Do not approach the lamp cover and the exhaust vents, while the projection
lamp is on.
WARNING
►Do not turn your device on prior to the projector, except for the
cases directed by the manuals of devices.
NOTICE
STANDBY/ON
SHUTTERSECURITYLAMPTEMPPOWER
STANDBY/ON
Power
switch
POWER
POWER indicator
STANDBY/ON
STANDBY/ON
button
Operating
Operating

20
Operating
1.
Turning off
2.
Press the
STANDBY/ON
STANDBY/ON button again while the
message is shown.
The projector lamp will go off, and the
POWER
POWER
indicator will begin blinking in orange.
Then the
POWER
POWER indicator will stop blinking
and light in steady orange when lamp cooling is
complete.
3. After making sure that the
POWER
POWER indicator lights in steady orange, and
press down the side marled “
O
O” on the power switch.
The
POWER
POWER indicator will go off.
• Use the shutdown switch only when the projector can be not turned
off by normal procedure.
NOTE
►Do not approach the lamp cover and the exhaust vents for a
while after the lamp goes out, since they may be hot and could cause burns.
WARNING
►Turn your device off prior to the projector, except for the cases
directed by the manuals of devices.
NOTICE
The following walks you through the steps to turn the projector off.
For other devices, follow the manual of each.
Press the
STANDBY/ON
STANDBY/ON button on the projector
or the remote control.
The message "Power off?" will appear on the
screen for about 5 seconds.
STANDBY/ON
SHUTTERSECURITYLAMPTEMPPOWER
STANDBY/ON
Using the elevator feet
Lengthening or shortening the length of the elevator feet shifts the projection
position and the projection angle.
Turn the elevator feet each to adjust their length
►Do not place the projector with an inclination of 5 degrees
or more. The projector leaned exceeding the limit could cause malfunction and
shorten the life of the projector.
CAUTION
5°
►Do not lengthen the elevator feet to 30 mm or more. The foot
lengthened exceeding the limit may come off and drop the projector down, and
result in an injury or damaging the projector.
WARNING
max.
30 mm
Power
switch
POWER
POWER indicator
STANDBY/ON
STANDBY/ON button