Dura-Max 68032 User manual

1
SPENCE 48” WALL MOUNTED FOLDING
WORKBENCH / TABLE / DESK
4
U.S. Polymers Inc.
1057 S. Vail Ave.
Montebello, CA 90640
United States of America
ITEM #68032
www.duramaxbp.com
IMPORTANT: READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE
WARNING
Your safety and the safety of others is important to us.
Failure to follow these guidelines can result in property damage or personal injury.
Customer Service: 1-888-444-0104 Monday - Friday: 8:00 a.m. - 4:30 p.m. PST
www.duramaxbp.com
SKU#68032-1 1 RD-1.0 30-08-2021
122 cm
48 in
Wall
51 cm
20 in
• The product is for indoor use only (Not for outdoor use).
• We strongly recommend that at least two or more adults move and install this unit.
• When installing directly into a non-concrete wall, do not attempt to install the bracket and wood top to the dry wall as this will
not support the weight.
• Use a stud nder to locate studs and secure safely.
• Always wear appropriate personal protection equipment when using tools and follow manufacturer’s operating instructions.
• Never apply more force/weight than the products published load limit.
• Do not make any modications to the product.
• Never operate unless the unit is properly installed and secured to concrete wall or studs.
• Never allow children to operate, play on, underneath or around the workbench.
• The top load capacity is 220 lbs. of static weight evenly distributed over the top.
• The brackets must be anchored to 2” studs to perform correctly and to be able to support the weight capacity.
• This product must be securely mounted on a at wall. Any misapplication of this product will void the warranty and the product
will be deemed unsafe due to owner’s installation error.
• If you do not feel comfortable installing this item, contact a licensed professional.
CARE AND MAINTENANCE
LIMITED LIFETIME WARRANTY
1. Use a soft, clean cloth that will not scratch the surface while cleaning.
2. Using solvents of any kind on your product may damage the nish.
3. Do not use any harsh abrasives or chemicals to clean any metal surface as it may damage the protective coating.
This product is warranted to the original purchaser. If there is a failure in this unit due to defects in materials or workmanship, the
manufacturer will repair or replace this item at our discretion without charge. Warranty is void if product has been assembled
incorrectly, misused, abused by overloading, altered in any way or damaged due to accident. This warranty is not transferable
and does not cover chipping, aking, scratches, rust, dents, or other damages to the surfaces of this product. Responsibility of the
manufacturer is limited to repair or replacement of this product. The manufacturer is not responsible for consequential, incidental,
or other damages or losses resulting from product failure.
This warranty is in lieu of all other expressed warranties. Some states do not allow the exclusion or limitation of incidental or
consequential damages, therefore, the above limitation may not apply to you. This warranty gives you specic legal rights and you
may have other rights which vary from state-to-state.
ASSEMBLY INSTRUCTIONS
Step 2
Operating Instructions
TO FOLD
Stand in front of the unit, lower it by pressing the
two release mechanisms simultaneously. Slowly
lower down to the folded position.
TO LIFT
To raise the workbench top, stand in front of
it and lift the top until you hear the brackets
click into the locked position.
FLAT FOLDING
E
A
E x 6
• Place the wood top on
the brackets.
• Make sure the wood top
is centered between the
two brackets and placed
close to the wall. (Do not
leave a large gap).
• Screw the 6 - M4 screws
underneath the wood
top to secure the top in
place.
Note: We recommend
that a second person
assists with this step to
hold the top in place.

3
A x 1
Wood Top
PARTS
PARTS LIST
2
A
B
B
Tools Required (Not Included)
Spanner 13Screw Driver Stud Finder
LevelSpeed Square
Socket Wrench 13 Tape Measure
B x 2
Mounting Bracket
C x 4
Expansion Bolt M8
D x 6
CSK Self Tapping Screw
M5 x 90mm
E x 6
Flat Head Screw
M4 x 25mm
Drill
Pencil
Drill Bit
( 13 mm / 3mm)
ASSEMBLY INSTRUCTIONS
Concrete Wall
Dry Wall
Step 1
C x 4
80 cm
C
C
B
B
D x 6
D
B
D
B
80 cm
IMPORTANT!
Use a Level to check if your
floor is even before making
your measurements.
• Determine and mark the
desired height of the
workbench on the wall
with a pencil.
• Measure 2 3/4” down
from your predetermined
workbench height and
pre-drill a hole with the
13mm drill bit.
• Secure bracket using
bolts provided.
• Note: Distance between
brackets should be
approximately 80cm.
• Repeat the previous
process and install the
second bracket.
• Use a level to make sure
both brackets are level,
and then pre-drill the
remaining holes.
• Make sure the bolts
are securely fastened.
Note: Is your oor level?
IMPORTANT!
Use a Level to check if your
floor is even before making
your measurements.
• Use a stud nder to nd
the closest studs and
mark the locations.
• Determine and mark the
desired height of the
workbench on the wall
with a pencil.
• Measure 2 3/4” down
from your predetermined
workbench height and
pre-drill a hole with the
3mm drill bit.
• Secure bracket using
screws provided.
• Note: Distance between
brackets should be
approximately 80cm.
• Repeat the previous
process and install the
second bracket.
• Use a level to make sure
both brackets are level,
and then pre-drill the
remaining holes.
• Make sure the screws
are securely fastened.
Note: Is your oor level?
13mm
5cm
3mm
5cm
WARNING BEFORE STARTING DETERMINE WALL TYPE AND FOLLOW
INSTALLATION INSTRUCTIONS.
Dry Wall: Do not install brackets directly to dry wall as the surface will not support the weight and can cause serious injury.
Concrete Wall: If installing directly into concrete, use the hardware provided to secure the brackets and follow installation instructions.