Durafly BRAVADO User manual

Features of the Bravado
Specications
Examine your kit carefully
1. ‘AirCore’ construction resulting in both a lightweight, yet strong structure.
2. Powerful set-up as standard for hardcore 3D and aerobatic performance.
3.Quick and easy assembly with minimum parts count.
4. Clean airframe design with easy battery access and generously sized control surfaces.
5. Made from durable and easy to maintain EPO foam and with spare parts readily available.
Wingspan: 1000mm ( 39.4 in.)
Flying Weight: 700-780g (1.5 -1.7lbs)
Motor: 2814 Kv1000
ESC: 40 Amp
Servo: 4 x Turnigy TG9d 9g digital servo’s
Radio：4/more channel
Receiver: 4/more channel
Battery: 3 cell 1000-1300mah lipo 25c min (required)
Prop: 11x
Recommended Environment: Outdoor/large indoor area.
Assembly Time: Less than 1 Hour
Duray model kits are subject to QC checks throughout production, and we sincerely hope that
you are completely satised with the contents of your kit. However, before assembling, we ask that
you check all parts against the parts list. If you are missing any parts, please contact Customer
Services via hobbyking.com. Also check for any damage to the any item within the box. Your model
has travelled a long way, and in some case could have sustained some damage. If you feel the
damage is beyond ressonable repare, please contact CS.
Please note:
We are constantly working on improving our models, therefore every model is subject to change
without notice.
This is a sophisticated hobby product and is NOT a toy. It must always be operated with caution,
common sense and some basic mechanical ability. This manual provides instructions as the the
assembly, safe opperation and maintainence of this hobby product. It is highly reccommneded that
you follow and read fullythe instructions and warnings stated in this manual including, safety,
assembly, set-up and ying guidelines in order to operate this product correctly and avoid damage
or serious injury.

Do not y under the conditions below
Foam parts included in the packing
Cautions for ying
Note for Storage
Tools:
•Strong winds (more than 20pmh)
•Other storm like conditions
•Area close to high voltage wires
•Area with high density population
•Never leave you ight battery installed in the model when storing.
•If hanging the model, ensure the control surfaces are not taking the weight of the model.
•Store away from direct sunlight and ideally at room temperature.
•Secure your model for storage incase it moves and gets damaged.
3
9
2
5
4
8
1
10
7
6
3
9
2. Wing
5. Winglet
8. Canopy
3. Left aileron
6. Rudder
9. Landing gear slice
1. Fuselage
4. Right aileron
7. Rudder bolt
10.Stabilizer
While parks make excellent ying areas, make sure you have permission to y there and follow safety
guidelines set by local authorities.
Required: Scissors, Balsa knife, Combination pliers, Screwdriver, Quick-dry glue
02

12
17
18
19
20
16
13
15
14 21
11
16. Tail wheel
17. 1155 propeller
18. Rudder pushrod (φ1.2 piano wire)
19. Elevator pushrod (φ1.2 piano wire)
20. Aileron pushrod (φ1.2 piano wire)
21. Screw (M3*8)
11.Landing gear
12. Spinner
13. Screw (M4*30)
14. Screw (M2*5)
15. Adjustor
Parts included in the packing

A
B
1
2
2
3
4
Assembly steps
1. Aseembly begins with the wing (2) and fuselage (1). Incert the wing panel into the slot in the
fuselage and glue in place. Insure that distance A is equal to B.
2. Hinges (4 for each side) can now be glued into the pre-cut slots of the trailing edge of the wing
(2). Once dryed you can then glue the ailerons(3&4) to the hinges.
04

4. The horizontal tail (17)can now be glued in place at the rear of the fusealge asr shown.
Ensure distances E and F are equal and that the tail is horizontally level.
C
D
51
F
17
1
E
3. Insert the fuselage winglet (5) into the upper fusealge slot and glue in place.
Ensure distance C is equal to D.

5. Place vertial trailing edge insert (7) into pre-cut slot at the rear of fuselage, then x with glue.
6. Connect Z bend (18) to servo control horn on rudder (6), then push pushrod into pushrod tube.
7
1
18
6
18
1
Fuselage Assembly
06

1
18 6
1
11
13
7. Glue 4 hinges into the rudder (6) then glue the rudder to the vertical tail (1) as shown below.
8. With the rudder in place the landing gear (11) can now be installed. Locate the supplied
M4x25mm bolts (13) and secure to the fuselage (1) using a screw driver as shown.
9. Once the landing gear (11) is secured, the gear foam cover (12) can be installed as shown with just
a small spot of glue.

11. Install your 9g servo’s of choice into the molded pockets on the underside of the wing by guiding the
wires through into the center of the fuselage and securing in place with some glue as shown below.
12
11
13
14 16
16
10. Locate the tail wheel assembly and install as detailed below using the supplied M2x5mm screws.
KIT ONLY
08

12. Glue the aileron control horn in place and connect the Z bend push rods (20) as shown. Ensure that your
servo horns are at 90 degree’s to the wing at this stage.
13. Your 9g rudder and elevator servo of choice can now be glued in place in the pre-molded pockets on
either side of the rear fuselage. NOTE, you must ensure your servo leads are long enough to reach the front
of the model, you may need to add extension leads so please check.
15
15
3
4
2
20
20
KIT ONLY
KIT ONLY

14. Both the rudder (not shown) and the elevator push-rod Z bend and control horn can now also be install
just as before. Again ensure your servo horn is at 90 degree’s to the fusealge.
17
19
15 1
1
21
KIT ONLY
KIT ONLY
15. Install your choice of 2814 class motor onto the rewall as show below. It is suggested that thread lock
be used.
10

17. Install your 30-40amp ESC of choice in the nose of the fuselage under the plastic battery tray as
detailed below.
9
10 9
1
KIT ONLY
18. Connect servo wires to coorisponding channels of your receiver and install directly behind the battery
tray on top of th wing center section. Secure in place with velcro.
16. Locate the spinner assembly and rst slide the spinner back plate (9) on the motor shaft followed
by theprop (10), washer and nut as shown. Firmly tighen the nut and nishby screwing the
spinner tip (9) in place.

Assembly of your Duray Bravado is now complete.
Before you move onto the nal set-up of the model, we suggest
you perform a nal check on all screws, bolts and components to
ensure all are secture and rmly in place.
12

CG 120-130mm
Control throws:
* Elevator ‘low rates’ 15mm ‘high rates’ 30mm in either direction from neutral. (travel, 120% up and 100% down)
* Aileron ‘low rates’ 10mm ‘high rates’ 15mm in either direction from neutral.
* Rudder ‘low rates’ 15mm ‘high rates’ 25mm in either direction from neutral.
6 -8 mm
6 -8 mm
Rudder
8 -12 mm
8-12 mm
Elevator
90-95 mm ~
6 - 10 mm
6 - 10 mm
Aileron
The centre of gravity (CG) should be at a position of 120mm-130mm away from leading edge, please
refer to above picture.
1. With your receiver installed and all servos plugged into their corresponding channels, connect the
ight battery to the ESC to power up the model. With the model now armed, ensure all servo’s are
centered and all control surfaces are level. If not, adjust by turning the control clevis’s by hand
accordingly until the control surfaces are level as shown.
Note: For saftey reasons, it is advised that this is done with the prop removed from the model.
Center of Gravity

With assembly and set-up now complete your Durafly Bravado
should now be ready for flight. However we recommend you read and follow the
advice given in thefollowing stages of this manual before flying your model.
MODEL FLYING PRECAUTIONS:
Remember to keep clear of the propeller at all times when your flight battery is
connected.
crowded areas
flight
14

Rudder
9095000106-0
Landing gear
9095000107-0
Tail Wheel
9095000108-0
Spinner
9095000107-0
Control accessories set
9095000116-0
Sticker Set
9095000113-0
Winglet
9095000104-0
Fuselage
9095000102-0
Canopy
9095000115-0
Stabilizer
9095000105-0
Wing
9095000103-0
Spare parts