Duratuf MARLBOROUGH User manual

11
MARLBOROUGH

22
BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE
SOME IMPORTANT POINTS
TOOLS REQUIRED
• Drill
• Hex Drive (5/16)
• Hex Drive (3/8)
• Drill Bit 3.5mm
• Drill Bit 10mm
• Square Drive Drill Bit
• Phillips Drill Bit
• Slotted Drill Bit
• Riveter
• Hammer
• Tape Measure
• Ladder
• String Line
• Adjustable Spanner
• Level
• Hand Saw
• Caulking Gun
• Tin Snips (Left & Right Hand)
• Flatle(ForRollerDoor)
• Pipe Wrench (For Roller Door)
• SkillsawandJigsaw(Foroptionaltimberoor)
• MasonryDrilland12mmMasonryBit(forconcreteoor)
BEFORE YOU START
• Read all instructions carefully.
• Identify all parts and check quantities against checklist, before starting.
SAFETY
• Do not attempt to build your shed in high winds.
• Beware of sharp edges.
• Protect your eyes and ears.
• Use electronic tools with care. Use a Safety Trip Switch.
• It is easier and quicker if this shed is erected by two people.
SELECT YOUR SITE
• Your shed must be level. Achieve this by either levelling the ground or by using blocks.
• Ifyourshedistobepositionedonwetordampground,werecommendthatyourshedisraisedupo󰀨thegroundslightly.
WARRANTY REQUIREMENTS
The following maintenance process needs to be adhered to, to qualify for the steel warranty of your Duratuf Guardian shed.
• Wash all surfaces annually using a hose and soft nylon brush.
• Within 2 km of coast – wash every 3 months as above. After a storm, wash the cladding and the gutters as soon as possible to remove any highly corrosive
salt deposits.
• Volcanic Ash Fallout – wash as soon as possible, removing fall out from roof and gutters.
• Do not allow manures, chemicals or other corrosive materials to have direct contact with cladding.
2

33
3
PARTS LIST
TIMBER
DESCRIPTION LENGTH QTY DIAGRAM CHECKED
Front/Back Base Plate 70 x 45 H4 (Green) 3.150m 2
End Base Plate 70 x45 H4 (Green) 3.010m 2
Front/Back Top Plate 70 x 45 H1 (Red) 3.150m 2
EndTop Plate 70 x 45 H1 (Red) 3.010m 2
Lintel 70 x 45 2.400m 1
Stud 70 x 45 (Yellow) 2.250m 12
Stud 70 x 45 (Yellow) 2.400m 6
Stud 70 x 45 (Yellow) 0.310m 3
Nog 70 x 45 0.990m 3
Nog 70 x 45 0.943m 6
Nog 70 x 45 0.240m 2
Ridge Beam 140 x 45 H1 with 92mm notch 3.150m 1
Ridge Beam 140 x 45 H1 with 44mm notch 3.150m 1
DESCRIPTION LENGTH QTY DIAGRAM CHECKED
Wall Sheet 3.150m 9
Roof Sheet 3.750m 4
Front Wall Sheet 0.375m 6
Half Front Wall Sheet (390mm wide) 3.150m 1
Roller Door 2.400m 1
CLADDING/FLASHING

44
HARDWARE/ACCESSORIES
DESCRIPTION LENGTH QTY PART# DIAGRAM CHECKED
Front Top Plate Flashing 3.150m 1 1001
Front Corner Flashing 2.510m 2 1002
Rear Corner Flashing 2.365m 2 1003
Door Top Flashing 2.595m 1 1004
Door Head Flashing 2.400m 1 1005
Door Jamb Flashing 2.100m 2 1006
Downpipe Cover Flashing 2.200m 1 1007
Barge Flashing 3.825m 2 1008
Fascia 3.275m 1 1009
Back Spouting 3.275m 1 1010
Spouting End Cap 0.040m 2 1011
4
DESCRIPTION LENGTH QTY DIAGRAM CHECKED
L-Brackets 40mm 4
Flathead Nails 90mm 160
Tek Screws 55mm 110
Tek Screws 25mm 220
Clouts 30mm 130
Tek Screws 100mm 16
Rivets 3.2mm 80
Dropper 80mm 1
Downpipe 80mm 3.000m 1
Downpipe Brackets 2
Silicone 1
Roll of DPC- 75mm wide 30m 1
Touch up paint and brush 1

55
DATE: / / PACKED BY:
5
TIMBER FLOOR
DESCRIPTION LENGTH QTY DIAGRAM CHECKED
Floor Joists 100 x 50 H4 3.120m 7
Floor Boards 150 x 25 H3 3.120m 21
Door Step Flashing 2.400m 1
Floor Nails 50mm 300
Tek Screws 100mm
14
OPTIONAL EXTRAS
CLEAR ROOF
DESCRIPTION LENGTH QTY DIAGRAM CHECKED
Clear Roof Panel 3.750m 1
PLY FLOOR
DESCRIPTION LENGTH QTY DIAGRAM CHECKED
Plywood 17mm treated 1.565m x 1.200m 4
Plywood 17mm treated 1.565m x 0.730m 2
Joists 70 x 45 H4 3.040m 6
Joists 70 x 45 H4 3.130m 2
Joists 70 x 45 H4 0.532m 1
Joists 70 x 45 H4 0.662m 1
Joists 70 x 45 H4 0.555m 3
Door Step Flashing 2.400m 1
Floor Screws 40mm 120
Floor Screws 75mm 100
Tek Screws 100mm 14

66
6
FOUNDATIONS
• No doubt by now you will have decided what sort of base you are putting down.
• Ifyouchoosearaisedfoundation,eitheraconcretebase,plywoodoor,ortimberoor,theshed
designpreventsthewaterfromowinginsidetheshed.
• Ifyouchosetopositionthesheddirectlyontotheground,thewatercanowdownthewallsand
under the bottom plate and into the shed.
CONCRETE BASE
• To build a concrete base we recommend the following.
• Concrete base should be 3130mm x 3130mm (this is
20mm smaller than the shed frame size, which allows
for a 10mm gap around the perimeter of the shed).
• Concrete base to be a minimum of 80mm thick and at least 100mm thick
around the perimeter. Base should be at least 50mm above ground line.
• Concrete base should be laid on a solid or compacted base.
• Plastic sheeting underneath concrete will prevent moisture coming through underneath.
• Ideallytheareaaroundthedoorwayshouldhaveaslightslopetoallowwatertoruno󰀨.Refertoplansfordoorwayposition.
10mm
100mm
80mm

77
PLYWOOD FLOOR
Select
6 x 3040mm Joists
2 x 3130mm Joists
1 x 532mm Joists
1 x 662mm Joists
3 x 555mm Joists
4 x Ply 1565mm x 1200mm
2 x Ply 1565mm x 730mm
• Layoutoorjoistsandassemblesuboorframeasshown,
nailing joists together with two 90mm nails per join.
7
3040mm
532mm
555mm
555mm
555mm
662mm
1520mm 1520mm
C
L
3130mm
SUB FLOOR FRAME
PLYWOOD SHOWING SCREWS Screws
1565mm
1565mm
1200mm1200mm
730mm
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
• Positionsuboorframeensuringframeiswell
supported, level and diagonals are correct.
• Using40mmscrews,screwplywoodtosuboorframe
as shown.
• Ensuretimberoorissu󰀩cientlysecureddownto
foundation.

88
TIMBER FLOOR
8
Select
7 x 3130mm Joists
21 x 3130mm Floor boards
• Layoutoorjoistsasshown,ensuringjoistsarespaced
evenly apart.
• Using50mmooringnails,nailaoorboardoneachend,
ensuringendsareushwithjoists.Makesureooris
level and joists are well supported.
SUB FLOOR FRAME
TIMBER SHOWING NAILS
• Layoutremainingoorboards.
• Measure diagonals to ensure measurements are equal
andoorissqare.
• Ripdownlastoorboardtosuitgapandnailo󰀨oor
with50mmooringnails(14nailsperboard).
• Ensuretimberoorissu󰀩cientlysecureddownto
foundation.
3130mm
3130mm
Nails
..
..
..
..
..
..
..
..........................................
..
..
..
..
..
..
..
..........................................
..........................................
..........................................
..........................................
..........................................
..........................................
3130mm
3130mm

99
9
TIMBER FRAME
2340
A
A
B
End Base Plates - 2
C
BFront/Back Base Plates - 2
CEnd Top plates - 2
DFront/Back Top Plates - 2
EStuds - 21
FRidge beam - 2
GNogs - 11
D
E
F
G
HLintel - 1
TIMBER FRAME - END WALLS
Select
2 x 3010mm Base Plates
2 x 3010mm Top Plates
8 x 2250mm Studs
6 x 943mm Nogs
• Select one 3010mm base plate (Green), one 3010mm
top plate (Red) and four studs (Yellow).
• Layoutplatesandfourstudsonaatsurfaceand
nail together using two 90mm nails per join. Studs are
positioned 943mm apart.
• Position nogs 1200mm up from underside of bottom
plate to centre of nog and nail in place.
• Repeat with second end wall frame.
H
45
45 45
45
45 45 45
1073
1132
2340
943
3010
943 943
3150
3150

1010
10
TIMBER FRAME - BACK WALL
Select
1 x 3150mm Base Plate
1 x 3150mm Top Plate
4 x 2250mm Studs
3 x 990mm Nogs
• Select one 3150mm base plate (Green), one 3150mm
top plate (Red) and four studs (Yellow).
• Layoutplatesandfourstudsonaatsurfaceand
nail together using two 90mm nails per join. Studs are
positioned 990mm apart.
• Position nogs 1200mm up from underside of bottom
plate to centre of nog and nail in place.
TIMBER FRAME - FRONT WALL
Select
1 x 3150mm Base Plate
1 x 3150mm Top Plate
1 x 2400mm Lintel
6 x 2400mm Studs
3 x 310mm Studs
2 x 240mm Nogs
• Select one 3150mm base plate (Green), one 3150mm
top plate (Red) and four studs (Yellow). Lay out plates
andtwostudsonaatsurfaceandnailtogetherusing
two 90mm nails per join.
• Nail one stud each side of doorway to top and bottom
using the 240mm nogs to establish correct position.
• Nail remaining two studs to inside of studs and top
and bottom plates to make a double stud each side of
doorway opening.
310
2090
240
3150
2490
45
45 45
45
45 45 45
1073
1132
2340
990
3150
990 990
2400
240 90
45 90
45
45 45
45
1132 1223
• Nail lintel to studs using the 310mm studs to establish correct height.
• Nail 310mm studs to top plate and lintel, spacing these evenly apart.