Duratuf TUF 400 User manual

ASSEMBLY INSTRUCTIONS
TUF 400
BASE SIZE 1.980m x 1.355m

CHECK OUT OUR ASSEMBLY VIDEO
2
Let Keith and Justin show you how to build your
Fortress shed like a professional.
When used in conjunction with these assembly instructions, Keith’s practical tips and tricks will
make your assembly experience that much simpler, giving you visual guidance through sections
that seem tricky on paper, and help you achieve a flawless end result.
To view the video visit www.duratuf.co.nz/fortress-assembly
Note: Assembly video features a TUF400. But can be used for reference for any other Fortress model.

Tools Required:
Before you start:
Safety:
Select your site:
• Drill
• Drill Bit 3.5mm
• Drill Bit 6mm (Only required if installing an optional Clear Roof Panel)
• Masonry Drill and 10mm Masonry Bit (Only required if installing a Bolt Down Kit)
• Riveter
• Hammer
• Nail Punch
• Tape Measure
• Ladder or Saw stool
• String Line
• Hex Bit 8mm
• Skill Saw or Jig Saw (for floor only)
• Read all instructions carefully.
• Identify all parts and check the quantities against checklist.
• If you are pouring your own raised concrete floor, please refer to Raised Base Plate
section now to familiarise yourself with the procedure prior to starting.
• Do not attempt to build your shed in high winds.
• Beware of sharp edges. For safety wear protective gloves—preferably rubber coated)
• Protect your eyes and ears with the appropriate safety gear
• Use electric tools with care. Use a Safety Trip Switch.
• It is easier and quicker if this shed is erected by two people.
• Your shed must be level. You can achieve this by either levelling and compacting the
ground or by using blocks or piles to create a level platform for the shed framing to sit
on.
• If you shed is to be positioned on wet or damp ground, we recommend that your shed is
raised up off the ground slightly to avoid moisture and mould in the shed. A Damp Proof
Course (DPC) membrane can also be used. This is available form your local hardware
store.
ASSEMBLY INSTRUCTIONS
3

QTY LENGTH
CHECKED OUT CHECKED IN
4 1.890
2 1.890
1 1.570
1 1.570
1 1.890
2 1.570
1 1.860
2 1.980 Front & Back
2 1.355 Ends
1 1.980 Back
1 1.980 Front
2 1.355 Ends
4 1.810 Studs
2 1.833 Studs
2 1.265 45 x 45 H1
1 0.106 45 x 45 H1
1 0.823 45 x 45 H1
1 1.890 45 x 45 H1
1
SECURITY
2Latches
1
1
ROOF SIZE: 2.010 x 1.570
COLOUR: _________________ INV #:_______________
TUF 400 PARTS LIST
Back Wall Nog
Front Left Nog
Front Right Nog
End Wall Nogs
BASE PLATES
- Red 90 x 45 H1
DESCRIPTION
Clear Roof Panel
3/4 Front Wall Sheet
Corner Wall Sheets
Roof Sheet Or
Folded Roof Sheets
PACKED BY:
DATE: / /
BASE SIZE: 1.980 x 1.355
TOP PLATES
TIMBER
Wall Sheets
Door
Touch-up Paint & Brush
- Green 45 x 45 H4
- Green 45 x 45 H4
Hardware Pack
- Red 45 x 45 H1
- Blue 45 x 45 H1
- Yellow 45 x 45 H1
- Red 45 x 45 H1
FLASHINGS
Assembly Instructions
Roof Flashing
2
1
1.890
2.000
1
2.010
Door Jambs
Top Plate Flashing
4

YELLOW
YELLOW
1.810
YELLOW
BLUE
YELLOW
BLUE
5
TUF 400 TIMBER FRAME
UNDERSTANDING THE TIMBER
FRAMING STRUCTURE.
1. The Corner Studs are marked in
yellow and are a different length to
the Door Studs (marked blue).
2. The Door Studs marked blue sit
either side of the door.
3. The Top and Bottom plates form the upper
and lower framing structure, and these are
rebated out so that they join well at the corners.
4. The Nogs are the timber
framing that circles the shed
half way up the walls.
ASSEMBLING THE FRAME
Step 1: Assembling the end wall frames.
1.1 Select 1 x End Bottom Plate (1.355m Green) and 1 x End Top
Plate (1.355m Red) and two Studs (Yellow).
1.2 Lay them out on a flat surface (fig.1) with the studs connecting the
plates at the corners. The top and bottom plates should have the
rebates at the ends FACING OUT (fig.2)
1.3 Nail together as shown using two 75mm nails per join (fig. 2).
1.4 Repeat with the other end frame.
fig. 2
BEFORE YOU START!
If you have poured a raised concrete pad for the floor and you would like the wall cladding to overlap the sides of
the floor pad, now is the time to make the change to the frame.
Simply trim 30mm off the length of each of the 6 studs. This will allow the wall cladding to protrude below the bottom
plate once attached and the overhang will provide excellent waterproofing. SEE PAGE 15 FOR MORE DETAILS
fig.1
Stud
Stud
Top Plate
Bottom Plate
TIMBER COLOUR REFERENCE
GREEN —BOTTOM PLATES
RED—TOP PLATES
YELLOW—CORNER STUDS
BLUE—DOOR STUDS
NOGS ARE UNPAINTED

fig.3
fig. 4
6
TUF 400 TIMBER FRAME
Step 2: Connecting the end frames together
2.1 Lie one completed end frame on a flat surface—preferably concrete.
2.2 Select 1 x Bottom Plate (1.980m Green) and holding it vertical, fit one end to
the matching green rebate on the end frame. (in green fig.3) and nail in
place with 2 x 75mm nails
2.3 Repeat with the remaining Bottom Plate. (in green fig.3)
2.4 Select the remaining rebated top plate (red) and repeat step 2.2 (in red
fig.3)
2.5 The final top plate is not rebated as it is intended to sit higher than the frame
to create the slope of the roof. Fit this plate into the remaining rebate on the
top plate and nail as per fig.4
Step 3: Fitting the last end frame and End Nog
3.1 The remaining end frame needs to be lifted into place on to the upright
timber fames. It is far easier with 2 people at this point. Lift and position the
remaining End Frame up onto the upright framing, fitting the corners into the
rebated ends. (red in fig.5)
Note: The front top plate has no rebate, so it is easier to tack this corner in
first as the others will sit into the rebates.
3.2 While someone supports the frame, nail each corner in place using two
75mm nails per join.
3.3 Select 1 x End wall nog and nail in place, centrally between the top and the
bottom plate (blue in fig.5)
Step 4: Finishing the remaining framing
4.1 Carefully roll frame over onto the front wall. (The side with the 90 x 45mm
non-rebated top plate is the front wall).
4.2 Select the 2 front wall nogs (106mm and 823mm) and the 2 door studs
(marked blue). Use the left nog (106mm) to position the left door stud (first at
the top & then at the bottom) and nail the studs in place using 2 x 75mm
nails at each end. (in green fig.6)
4.3 Then position the LH Nog in the centre, between the top and the bottom
plate and nail in place using 2 x 75mm nails.
4.4 Repeat with the RH door stud and nog (823mm) (in blue fig.6)
4.5 Finish inserting the 2 nogs to the remaining end walls by rolling the frame
carefully over and repeating step 3.3
4.6 Once all nogs are in place, carefully roll the framing onto its base (fig.7). If
you are fitting a Duratuf Timber Floor Kit, now is the time to fit the floor joists.
4.7 Evenly space floor joists and nail them in place using three 75mm nails per
end. (in red fig.7)
CONGRATULATIONS YOUR FRAMING IS NOW COMPLETE
fig. 5
fig. 6
fig. 7

Top Plate Flashing
903mm180mm
3/4 Sheet
CLADDING DETAIL
Birds Eye View
fig. 10
BEFORE YOU START FIXING THE CLADDING
To avoid corrosion, where at all possible try not to trap metal filings between the steel sheets. Remove all
metal filings before riveting. Only use a ballpoint pen to mark the steel as the carbon in pencils reacts with
the Zinc/Aluminium coating.
Step 6: Fixing the Door Jambs in position (fig.9)
6.1 Position the left hand Door Jamb Flashing at the correct
measurement from left (fig.11) and nail to the Top Plate
using a 30mm clout (see fig.10 for detail). Pre-drill holes
to make nailing easier.
Flashing measurement is taken from protruding face of flashing.
6.2 Repeat with the bottom of the door Jamb
6.3 Position the right hand Door Jamb using the door opening
measurement of 903mm (fig.11) and nail this in place top
and bottom with 2 x 30mm clouts.
TUF 400 WALL CLADDING
7
Step 5: Fitting the front Top Plate Flashing
5.1 The top front plate flashing is positioned centrally on the top plate at
the front of the shed (the wide lip is on top). It will overhang slightly at
each end. Nail down from the top with 1 x 30mm Clout at each end
and 2 x more evenly spaced in the middle.
fig. 8
FRONT VIEW
DOOR JAMB
fig. 9
fig. 11
Before moving to the next step, please study the
details of how the steel cladding sheets overlap
each other. Then turn over and start attaching the
cladding.
Each cladding sheet has one edge that finishes with a
rounded “rib” that will overlap and sit on the top. The
other edge has an extra lip and will sit underneath.

Step 7: Fitting the wall cladding
It is very important that the Wall Sheets are positioned
exactly as shown in the cladding detail diagram on the
previous page.
7.1 Position the corner wall sheets as per (fig.13)
Check that the lip is on the correct side of the
sheet.
7.2 While holding the first corner Wall Sheet flush
with the top of the Top Plate (push hard up
under the Top Plate Flashing on the front wall),
nail to the Top and Bottom Plates using only 1 x
30mm clout at the top and 1 x at the bottom.
7.4 Repeat with all 4 corner sheets, remembering
to ensure the side with the lip is correct as per
(fig.13)
You should now have your cladding attached as per
(fig.14)
7.5 Now, overlap the end wall sheets together in
the centre. Square the wall of the shed by
pushing sideways as necessary until the
cladding sheets are flush with the top plate and
line up together, then rivet them together top
and bottom through the rib (figs.12 & 15)
7.6 Take the 2 x back wall sheets, lay them out and
overlap them together. Rivet them together top
and bottom through the rib.
7.7 Now that the back wall sheets are joined, place
them in position against the framing on the back
wall (ensuring that they overlap the corner
sheets correctly, and rivet them top and bottom
to the corner sheets (fig 15).
7.8 Select the 3/4 Front Wall Sheet. Position it to
the right of the doorway, overlap the rib with the
corner sheet and rivet top and bottom . (fig 15).
All your wall sheets should now be joined together
and tacked loosely to the framing.
7.9 While holding the Front Wall Sheets hard up
under the Top Plate Flashing, nail to the top
and bottom plates using 30mm clouts. Use 1
clout either side of each rib as per (fig.12)
7.10 Now work your way around the shed and
complete nailing your cladding on. Start with the
middle of the wall and work out, putting one
30mm clout either side of the rib, into the top
and bottom plates. (fig.12)
7.11 Once the cladding is secured to the top and
bottom plates, mark where the centre nogs are
positioned (half way up the shed), and put 1 x
30mm clout into each pan, positioned next to
the rib.
TUF 400 WALL CLADDING
8
3/4 Sheet
= Rivet = 30mm Clout
fig. 14
fig. 15
Back wall sheets
End wall sheets
fig. 12
fig. 13

Step 8: Finishing The Door Jamb Flashings
The wall cladding should now be sitting in
behind the Door Jamb flashings either side of
the door.
8.1 Right Door Jamb—Drill a hole through the front
face of the Right Hand Door Jamb Flashing
(including the rib of the cladding beneath) in line
with the top plate. Using a 50mm nail, secure into
the top plate. (fig. 16).
8.2 Repeat at the bottom into the bottom plate.
8.3 Using three 30mm Clouts at equal spacings nail
the door jamb to the stud on the inside lip of the
door jamb. (fig. 17).
8.4 Next to each of the 3 evenly spaced clouts, drill a
hole on the front face of the door jamb through
into the cladding rib beneath and fix with a rivet.
8.5 Repeat steps 8.1 to 8.4 with the left door jamb.
TUF 400 DOOR JAMBS
(fig. 16).
(fig. 17).
9

Step 9: Fitting a standard steel roof (Note—if fitting a Clear Roof Panel see Steps 9.1A & 9.8A)
Use a 3.5mm drill bit for all rivets and roofing screws on a standard
steel roof. Use 6mm drill bit for the roofing screws when drilling
into the Clear Roof Panels
9.1 Place the roof sheets onto the roof. The biggest bevel on the
end sheets faces to the front. Make sure that the overlap is
correct see (fig.18).
9.1A If using a Clear Roof Panel, position the 2 x side sheets in
place first, and then place the Clear Roof Panel so that it laps
over the top of both steel roof sheets.
9.2 For the standard steel roof, align all the sheets at the front and back and rivet through the overlapping ribs,
300mm from the front and 300mm from the back. When drilling and riveting a clear roof panel, take care as they
are brittle and can crack if not fitted correctly.
9.3 Once the roof sheets are joined together, position the roof so that the front overhang measures 150mm (fig.19).
9.4 With the front overhang at 150mm, drill a 3.5mm hole through the side of the roof sheet into the corner rib of the
wall (fig.19) and rivet. Do the same at the back, and on every second rib.
9.5 Repeat at the other end of the roof, ensuring that the front overhang measures 150mm.
fig. 19
Screwing the roof on
9.6 Make sure that the shed is square and that the walls are sitting straight. Check that the
walls are not bowed in our out, as once the roof has been screwed on you will not be
able to change this.
9.7 Line up the ribs on the roof with the ribs on the wall cladding (fig.20).
9.8 Starting from the front of the roof, while someone holds the Front wall straight, pre
-drill the roof (through the top of the rib) in line with the top plate. Use a 3.5mm drill
bit for a standard roof.
9.8A When fixing a Clear Roof Panel, use a 6mm drill bit when drilling into the clear roof
material to stop the roofing screws splitting the material.
9.9 Screw the roof to the Top Plate using one 55mm Roofing Screw on each rib. (Outside ribs do not need to be
fastened).
9.10 Repeat at the back. Note: a string line can be used to make this easier.
Pan Rib
TUF 400 ROOF
10
BEFORE YOU START FITTING THE ROOF
Condensation can form on the under side of shed roof. If building paper is required, now is the time to fit it. Building
paper will need to be supported underneath by stretching wire netting across the shed to support it from sagging over
time. A large mesh wire netting is ideal for this and is available at most DIY stores.
Please note that there is a slightly different layout to the roof sheets if you are fitting an optional Clear Roof Panel
fig. 18
Fig. 20

Step 10: Fitting the Front Roof Flashing
To finish the roof, the only thing left to do is fit the Front Roof Flashing as shown. When
positioned correctly rivet through Roof Flashing into Roof Sheet joins.
10.1 Select the front roof flashing and with the long
edge at the top, place it over the front of the roof
sheet in between the barges. (fig.21)
10.2 Using the 3.5mm drill bit, drill down from the top
of the flashing into the 2 x end ribs of the roof
(one at each end) and rivet each one.
10.3 Repeat with every second rib in between.
YOUR ROOF IS NOW FINISHED fig. 21
TUF 400 FRONT ROOF FLASHING
11
TUF 400 POSITIONING SHED
fig. 22
Step 11: Positioning your shed and ensuring it is square
and level.
11.1 It is important to make sure that your shed is now square
and level so that the door will open correctly. Place your
shed into it’s final position.
11.2 Measure across from corner to corner one way (using the
inside of the timber framing is the easiest way) and note
down the measurement. Then measure the opposite
diagonal and note this down. Your shed will be square
when both of these measurements are the same.
11.3 Adjust your shed by pushing the corners in or out until
both diagonal measurements are equal.
11.4 Using a level, ensure that the shed is flat and level.
11.5 If shed has a floor, ensure timber joists are adequately
supported, at each end and approx. 600mm spacings.

BEFORE YOU START, PLEASE NOTE THAT IF YOUR SHED HAS AN OPTIONAL SECURITY DOOR UPGRADE,
PLEASE GO TO THE NEXT PAGE FOR FITTING INSTRUCTIONS.
12
TUF 400 FITTING THE DOOR (STANDARD)
fig. 23
Step 12: Hanging the door. (Standard Door).
See next page for Security door instructions.
12.1 Hold the door in the open position with the hinges
against the right hand door jamb. Hold or prop it
with a wedge or wooden block, approximately
5mm down from Top Plate Flashing.
12.2 Drill one hole through the top hinge into the door
jamb and fit the rivet (fig.23). This is to hold the
door in place while you can check that it is
swinging true. Repeat with one rivet into the
bottom hinge.
12.3 Close the door and check that the door is sitting
square and is not binding on the right hand door
jamb.
12.4 If the door is binding, drill out the rivet on one
hinge at a time and adjust the position of the
hinge so that it fixes the issue. Once the door is
swinging freely and sitting square within the
frame, move to step 12.5.
12.5 Drill and place rivets into the remaining holes on
all 3 door hinges.
fig. 23
Step 13: Fitting the Padbolt
13.1 Position the padbolt on the door as shown in
(fig.24). The padbolt should be nearly flush with
the edge of the door.
13.2 Drill and rivet the padbolt onto door using all 4
holes provided.
13.3 Fit the padbolt keeper as shown.
fig. 24

Step 14: Fitting the locking mechanism onto the
locking door handles.
14.1 Starting with the top handle, slide the latch onto
the handle shaft.
14.2 Enter the shed, close the door and turn the latch
so that it is in the locked position. Adjust the latch
so it is firmly against the back of the timber door
stud as this will stop the door from opening when
locked.
14.3 Tighten up the bolt on the latch so that it wont
come loose when the door is tampered with.
14.4 Repeat for second door handle.
TUF 400 SECURITY DOOR (Optional)
13
IF YOU HAVE PURCHASED THE OPTIONAL SECURITY DOOR, IT WILL COME FITTED WITH 2 X KEY-LOCKING
DOOR HANDLES AND EXTRA STRUCTURAL FRAMING.
HANDLE SHAFT
LATCH

Step 15: Marking and cutting the floor to fit.
15.1 Select a Floor Board and lay it across the floor joists and
bottom plates and push up against the front wall. Mark
out where Studs are as the floor board will need to be cut
out to fit in correctly. (fig.25)
15.2 Complete marking the square cut out that will be required
to be removed and cut these with a Jigsaw.
15.3 Repeat with the back Floor board.
15.4 Once these boards are cut so that they fit snugly in place,
nail them in.
15.5 Lay out the remaining floor boards and cut around any
other studs as required.
15.6 When the boards are tightly in place, you will likely need
to mark the final board and cut this down lengthwise to
the correct width.
HANDY TIP
Cut the final floorboard slightly wide for the gap. Place the
final 2 floorboards with their outside edges in place, and
their touching edges up in an A shape position. When you
step on these boards to flatten them out, they will wedge
the rest of the floorboards in tight. Make sure they are
accurately placed lengthwise prior to wedging them in
(fig.26)
15.7 Nail in each Floor Board, two 50mm nails each end and
two into each Floor Joist.(fig.27)
YOUR OPTIONAL FLOOR KIT IS NOW FULLY INSTALLED!
TUF 400 TIMBER FLOOR KIT (Optional)
14
fig. 26
BEFORE YOU START, IF YOU ARE ANCHORING YOUR SHED TO THE GROUND USING A DURATUF TIMBER
PEG DOWN KIT, PLEASE DO THIS NOW.
YOU SHOULD HAVE FITTED THE FLOOR JOISTS IN STEP 4.7. IF YOU HAVENT FINISHED STEP 4.7, RETURN TO
PAGE 6 AND DO SO.
fig. 25
fig. 27

• Remove all metal filings with a soft brush or rag.
• Hose down roof and walls thoroughly.
• Painting Zinc/Aluminium coated steel will extend its life in most environments
• The surface must be dry and free of dirt, oil, grease and other contaminants prior to painting, but no weathering of
the surface is required
• Zinc rich primers are recommended for use, along with a two coat finishing system. Paint suppliers should be con-
sulted for the most suitable paint system to ensure compatibility of primers and topcoats.
For sheds being placed on a purpose built floor, we
recommend that the studs are shortened by 30mm.
The Wall Sheets will then protrude 20mm below the
Base Plate. This will stop water flowing in between
the Base Plate and Floor.
If you choose this option, the Floor should be made
15mm smaller than Base Size.
Note: Although it is not essential, fitting Damp
Proof Course in between the Base Plate and
the Floor will give added protection against
moisture.
i.e. CONCRETE / PLYWOOD
PAINTING
CLEAN UP
PURPOSE BUILT FLOOR

DURATUF PREMIUM SHED WARRANTY
GUARANTEE TO CUSTOMER
Congratulations on purchasing a Duratuf Storage Shed. With proper care and attention, this product will last many years.
For your benefit PLEASE READ THE FOLLOWING INFORMATION CAREFULLY.
WARRANTY ON METAL CLADDING
Riverlea Group Ltd guarantee that the metal roofing and wall cladding on Kiwi and Fortress Garden Sheds may be used in moderate and inland corrosion zones or areas where
the first year mild steel corrosion rate is less than 200g/m2, and that in these conditions, they will not perforate due to corrosion within 30 years of date of manufacture.
TERMS AND CONDITIONS
1. Damage or corrosion due to the following circumstances is not covered by this warranty.
 Mechanical, chemical or other damage sustained during or after installation.
NOTE: Clean swarf off shed IMMEDIATELY after assembly
Do NOT mark cladding with pencil
Do NOT allow manures, chemicals or other corrosive materials to have direct contact with cladding
Chemical damage will result if these instructions are not carried out
 Force majeure or other causes beyond the control of Riverlea Group Ltd.
2. This warranty does not cover material installed in severe and very severe environmental situations, or in any area where the mild steel corrosion rate (as published by
BRANZ) exceeds 200g/m2.
3. Minimum maintenance must be carried out in accordance with instructions below.
Should the cladding fail to perform as specified above, the liability of Riverlea Group Ltd shall in all cases be limited to replacing or repairing the defective product. The bal-
ance of the original warranty will cover any repaired or replaced material. Riverlea Group Ltd will not be liable for any consequential loss or damage, labour or transport charg-
es. All claims made in writing within 21 days of discovery, quoting the reference number at the top right hand corner of this page.
MAINTENANCE
Following are the minimum maintenance requirements for cladding used in Kiwi Garden Sheds and Fortress Sheds.
 Washing all surfaces by rain, and annual hosing of sheltered areas using a hose and soft nylon brush.
 Within 2km of coast—wash every 3 months as above. After a storm, wash the cladding and the gutters as soon as possible to remove any highly corrosive
salt deposits.
 Volcanic Ash Fallout—wash as soon as possible, removing fallout from roof and gutters
 Gutters to be kept clean of leaves and dirt.
Should you require additional technical information please contact us at the details below.
Please visit www.duratuf.co.nz/warranty to validate the Warranty on your shed.
Click on the Warranty Registration Link and complete all details.
If you are unable to access the computer, please phone us on 0800 438 274 and one of the customer services team will help you to acti-
vate the warranty on your garden shed.
Many thanks, from the Team at Riverlea Group.
WARRANTY REGISTRATION

COMPLETE OUR CUSTOMER SURVEY
Thank you for investing in a Duratuf Garden Shed.
We are sure that it will provide excellent long-term storage and add value to your property. To continually improve our products and
service, we would love to hear about your Duratuf experience and why you chose us.
Further to that, we would also love to see a picture or a short video of your shed installed and doing its job so that we can share this
with others for their inspiration. Thank you in advance and we look forward to receiving your feedback!
To complete the survey please visit
www.duratuf.co.nz/customer-survey
Complete the survey for your chance to
WIN a $100 Prezzy Card!