Dyer D+H GVL 8301-K User manual

GVL 8301-K instructions

GVL 8301-K
6/12 GVL 8301-K
Deutsch 99.821.72 1.4/02/16
ST OP ST OP ST OP
Bedienung - Tägliche Lüftung
Öffnen: Schliessen: Stoppen:
Lüftungstaster benötigt
STOP
Nur wenn Wind- oder Regenmelder vorhanden:
Wenn die Wetterautomatik über den Lüftungstaster LT 84-U-W
(optional) eingeschaltet ist, läuft die Anlage bei Wind oder Regen zu.
Sie läuft nach Wind- oder Regenende nicht automatisch wieder auf.
Öffnung der Anlage zum Lüften über den Lüftungstaster.
Soll bei schlechtem Wetter Spaltlüftung betrieben werden, so kann die
Wetterautomatik am LT 84-U-W (optional) abgeschaltet werden. Ist
kein LT 84-U-W vorhanden, ist Spaltlüftungsbetrieb bei schlechtem
Wetter nicht möglich.
Bedienung - Wetterautomatik
Automatic
on/off
LT 84-U-W
Konformitätserklärung
Wir erklären in alleiniger Verantwortung, dass das
unter „Technische Daten“ beschriebene Produkt mit
den folgenden Richtlinien übereinstimmt:
2014/30/1EU, 2014/35/EU
Technische Unterlagen bei:
D+H Mechatronic AG, D-22949 Ammersbek
Dirk Dingfelder Maik Schmees
Vorstand Prokurist, Technischer Leiter
22.02.2016
Elektrogeräte, Zubehör, Batterien und Verpackungen
sollen einer umweltgerechten Wiederverwertung
zugeführt werden. Werfen Sie Elektrogeräte und
Batterien nicht inden Hausmüll!
Nur für EU-Länder:
Gemäß der Europäischen Richtlinie 2012/19/EU
über Elektro- und Elektronik-Altgeräte und ihrer
Umsetzung in nationales Recht müssen nicht mehr
gebrauchsfähige Elektrogeräte getrennt gesammelt
und einer umweltgerechten Wiederverwertung
zugeführt werden.
Entsorgung
Safety notes
Operating voltage 230 V AC!
Risk of injury from electric shock!
- Connection has to be carried out only by an
authorized electrical specialist
- Only for inside mounting
- Just use unchanged original D+H parts
Guarantee
You will get 2 years guarantee for all D+H products
from date of verified handing over of the system up to
maximal 3 years after date of delivery, when
mounting and starting has been carried out by an
authorized D+H-distributor.
D+H guarantee is expired, with connection of D+H
components with external systems or with mixing of
D+H products with parts of other manufacturers.
Performance features
- Ventilation safety function (key operation
OPEN/CLOSE)
- Entry for external control, e.g. timer
- Possibility of connecting rain detector or wind/ rain
detector without supplementary module
- Plastic housing, surface mounted type
Intended use
- Ventilation control for small sized building objects
- For triggering of 24 V DC drives
- 1 ventilation group
- 1 A total actuating current
- Expandable with D+H accessories
- Only for indoor mounting
WARNING
Read all safety warnings, instructions, illustrations
and specifications provided with this product.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
Assembly scheme
* optional function extension (separate components, retrofitable!)
This instruction includes descriptions and connection plans of components which are not part of scope of
supply of control panel. You can order these parts and many more separately from your D+H distributor.
Further connecting plans are available there as well.
group
window drives*
vent button* room temp. control* Control panel (GVL 8301-K) rain sensor*
external control*
Wartung und Reinigung
Die Inspektion und Wartung hat gemäß den D+H-
Wartungshinweisen zu erfolgen. Es dürfen nur
original D+H-Ersatzteile verwendet werden. Eine
Instandsetzung erfolgt ausschließlich durch D+H.
Wischen Sie Verschmutzungen mit einem trock-
enen, weichen Tuch ab.
Verwenden Sie keine Reinigungs- oder Lösemittel.
Table of contents
Intended use...........................................................7
Safety notes............................................................7
Performance features / Guarantee..........................7
Assembly scheme ..................................................7
View motherboard ..................................................8
Technical Data........................................................8
Wiring plan..............................................................9
230 V AC supply......................................................9
Connection...........................................................10
Operation..............................................................11
Declaration of Conformity......................................11
Maintenance and cleaning / Disposal ....................11

GVL 8301-K
GVL 8301-K 9/12
English
99.821.72 1.4/02/16
Type GVL 8301-K
Nominal voltage 230 V AC, 50 Hz
Rated power 30 VA
Stand-by operating 4,3 W
Class of rating short-time duty, 20%
Protection class II
Ingress protection IP 54
Temperature range -5...+60°C
Output voltage 24 V DC, unstabilized
Output current max. 1 A
Housing plastic
Colour light grey (~RAL 7035)
Dimensions 139 x 119 x 70 mm
Technical Data CLOSE diode
Safety function!
The CLOSE diode, marked above, must be cut out
with side cutting pliers, if the window, which is to
open, is within arm's reach (fitting heights of the
window less than 2,5 m). Through this, a „key
operation function" will be achieved with closing of
the window. The window wing will be closing only
as long as the vent button is operated.
In this case, automatic control is not permissible,
e.g. by room temperature control or wind/rain
detector.
Observe the safety notes which are
included to the drive!
View motherboard
T0,2A
fuse mains drive connector230 V protection capmains connector connector for
central control
CLOSE
Diode
(s.b.)
spare
fuses
OPEN
Diode Output voltage 24 V DC!
Do not run cables together with power lines!
In case of a cable with ground wire
(e.g. green / yellow) this must not be used!
Wiring plan (Paragon)
230 V AC, 50 Hz
to further ones
see line lenghts and cross sections
window drive control panel
vent button
ca. 1,2 m above
upper edge
firm flooring
external
control
4x 0,8 Ø
4x 0,8 Ø
2x 0,8 Ø
4x 0,8 Ø
rain sensor room temperature
control
Line lenghts and cross sections
Cross section (mm²) = cable lenght (m) x total current
80
total current
0.5 A
240
400
640
1 A
120
200
320
m
m
m
type
2x 1,5 mm²
2x 2,5 mm²
2x 4 mm²
230 V AC supply
Covering
Place enclosed protection cap
over supply terminal after mains
cable has been connected.
L
N
PE
230 V AC, 50 Hz

GVL 8301-K
8/12 GVL 8301-K
English 99.821.72 1.4/02/16
Type GVL 8301-K
Nominal voltage 230 V AC, 50 Hz
Rated power 30 VA
Stand-by operating 4,3 W
Class of rating short-time duty, 20%
Protection class II
Ingress protection IP 54
Temperature range -5...+60°C
Output voltage 24 V DC, unstabilized
Output current max. 1 A
Housing plastic
Colour light grey (~RAL 7035)
Dimensions 139 x 119 x 70 mm
Technical Data CLOSE diode
Safety function!
The CLOSE diode, marked above, must be cut out
with side cutting pliers, if the window, which is to
open, is within arm's reach (fitting heights of the
window less than 2,5 m). Through this, a „key
operation function" will be achieved with closing of
the window. The window wing will be closing only
as long as the vent button is operated.
In this case, automatic control is not permissible,
e.g. by room temperature control or wind/rain
detector.
Observe the safety notes which are
included to the drive!
View motherboard
T0,2A
fuse mains drive connector230 V protection capmains connector connector for
central control
CLOSE
Diode
(s.b.)
spare
fuses
OPEN
Diode Output voltage 24 V DC!
Do not run cables together with power lines!
In case of a cable with ground wire
(e.g. green / yellow) this must not be used!
Wiring plan (Paragon)
230 V AC, 50 Hz
to further ones
see line lenghts and cross sections
window drive control panel
vent button
ca. 1,2 m above
upper edge
firm flooring
external
control
4x 0,8 Ø
4x 0,8 Ø
2x 0,8 Ø
4x 0,8 Ø
rain sensor room temperature
control
Line lenghts and cross sections
Cross section (mm²) = cable lenght (m) x total current
80
total current
0.5 A
240
400
640
1 A
120
200
320
m
m
m
type
2x 1,5 mm²
2x 2,5 mm²
2x 4 mm²
230 V AC supply
Covering
Place enclosed protection cap
over supply terminal after mains
cable has been connected.
L
N
PE
230 V AC, 50 Hz

GVL 8301-K
GVL 8301-K 11/12
English
99.821.72 1.4/02/16
Electrical devices, accessories, batteries and packa-
ging should be sorted for environmental-friendly
recycling. Do not dispose electrical devices and
batteries into household waste!
Only for EC countries:
According the European Guideline 2012/19/EU for
waste electrical and electronic equipment and its
implementation into national right, electrcal devices
that are no longer usable must be collected separa-
tely and disposed of in an environmentally correct
manner.
DisposalDeclaration of Conformity
We declare under our sole responsibility that the
product described under “Technical Data” is in
conformity with the following directives:
2014/30/EU, 2014/35/EU
Technical file at:
D+H Mechatronic AG, D-22949 Ammersbek
Dirk Dingfelder Maik Schmees
Member of the Board Authorized signatory, Technical Director
22.02.2016
Only if wind detector or rain detector available:
If the weather automatic is switched on via vent button LT 84-U-W
(optional), the system will automatically close in case of wind or rain.
The system will not automatically open again, if wind or rain has
stopped. Opening of the system for ventilation via vent button.
The weather automatic can be switched-off at vent button LT 84-U-W
(optional), if gap ventilation is required in case of bad weather.
Gap ventilation is not possible in case of bad weather, if no vent
button LT 84-U-W available.
Operation - Weather automatic
Automatic
on/off
LT 84-U-W
ST OP ST OP ST OP
Operation - Day-to-day ventilation
Open: Close: Stop:
Ventilation button required.
STOP
Connection examples
–
51
3
2
RTR 231
VRS 10
– –
+24V
21 3 4 5 6
24 V DC
Window
Drive
PPS
LT 84-U-W
M1
GVL 8301-K
–
X1
1 2
Mot.b
5
Mot.b
8
Mot.b
1
Mot.a
4
Mot.a
7
Mot.a
3
Fail / TMS+
6
Fail / TMS+
9
Fail / TMS+
8
A Z
7
–N
65
L
4
Az Zz
3
+G
2
M2 M3
VCD 20x
VRS 10
– –
+24V
21 3 4 5 6
2x 24 V DC
Window drives
on one window
PPS
LT 84-U-W
M1
GVL 8301-K
–
X1
1 2
Mot.b
5
Mot.b
8
Mot.b
1
Mot.a
4
Mot.a
7
Mot.a
3
Fail / TMS+
6
Fail / TMS+
9
Fail / TMS+
8
A Z
7
–N
65
L
4
Az Zz
3
+G
2
M2 M3
VCD 20xLT 84-U
LT 84-U
* Connect lead directly when no automatic switch available. In this case the manual operation is out of function.
Ask your local D+H partner for further connection examples.
Automatic
on/off
Automatic
on/off
ST OP
ST OP
Maintenance and cleaning
Inspection and maintenance has to be carried out
according to D+H maintenance notes. Only original
D+H spare parts may be used. Repair is to be carried
out exclusively by D+H.
Wipe away debris or contamination with a dry, soft
cloth.
Do not use cleaning agents or solvents.

GVL 8301-K
10/12 GVL 8301-K
English 99.821.72 1.4/02/16
Electrical devices, accessories, batteries and packa-
ging should be sorted for environmental-friendly
recycling. Do not dispose electrical devices and
batteries into household waste!
Only for EC countries:
According the European Guideline 2012/19/EU for
waste electrical and electronic equipment and its
implementation into national right, electrcal devices
that are no longer usable must be collected separa-
tely and disposed of in an environmentally correct
manner.
DisposalDeclaration of Conformity
We declare under our sole responsibility that the
product described under “Technical Data” is in
conformity with the following directives:
2014/30/EU, 2014/35/EU
Technical file at:
D+H Mechatronic AG, D-22949 Ammersbek
Dirk Dingfelder Maik Schmees
Member of the Board Authorized signatory, Technical Director
22.02.2016
Only if wind detector or rain detector available:
If the weather automatic is switched on via vent button LT 84-U-W
(optional), the system will automatically close in case of wind or rain.
The system will not automatically open again, if wind or rain has
stopped. Opening of the system for ventilation via vent button.
The weather automatic can be switched-off at vent button LT 84-U-W
(optional), if gap ventilation is required in case of bad weather.
Gap ventilation is not possible in case of bad weather, if no vent
button LT 84-U-W available.
Operation - Weather automatic
Automatic
on/off
LT 84-U-W
ST OP ST OP ST OP
Operation - Day-to-day ventilation
Open: Close: Stop:
Ventilation button required.
STOP
Connection examples
–
51
3
2
RTR 231
VRS 10
– –
+24V
21 3 4 5 6
24 V DC
Window
Drive
PPS
LT 84-U-W
M1
GVL 8301-K
–
X1
1 2
Mot.b
5
Mot.b
8
Mot.b
1
Mot.a
4
Mot.a
7
Mot.a
3
Fail / TMS+
6
Fail / TMS+
9
Fail / TMS+
8
A Z
7
–N
65
L
4
Az Zz
3
+G
2
M2 M3
VCD 20x
VRS 10
– –
+24V
21 3 4 5 6
2x 24 V DC
Window drives
on one window
PPS
LT 84-U-W
M1
GVL 8301-K
–
X1
1 2
Mot.b
5
Mot.b
8
Mot.b
1
Mot.a
4
Mot.a
7
Mot.a
3
Fail / TMS+
6
Fail / TMS+
9
Fail / TMS+
8
A Z
7
–N
65
L
4
Az Zz
3
+G
2
M2 M3
VCD 20xLT 84-U
LT 84-U
* Connect lead directly when no automatic switch available. In this case the manual operation is out of function.
Ask your local D+H partner for further connection examples.
Automatic
on/off
Automatic
on/off
ST OP
ST OP
Maintenance and cleaning
Inspection and maintenance has to be carried out
according to D+H maintenance notes. Only original
D+H spare parts may be used. Repair is to be carried
out exclusively by D+H.
Wipe away debris or contamination with a dry, soft
cloth.
Do not use cleaning agents or solvents.

Dyer Environmental Controls Ltd
Unit 10 Lawnhurst Trading Estate, Cheadle Heath,
Stockport SK3 0SD
Tel: [phone]
E-Mail: [email protected]
www.dyerenvironmental.co.uk