Dymo LabelManager Series User manual

LabelMANAGER
User Guide

DYMO Corporation
44 Commerce Road
Stamford, CT 06902-4561
Phone: [phone]
Fax: [phone]
Declaration
of Conformity
(for US models only)
Equipment Information
Description: Thermal Transfer Printer
Model: LabelMANAGER PC (18949)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC (Federal Communications Committee) rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try correcting the
interference by one or more of the following measures:
•Reorient the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
•Use shielded cables to connect this device to computers.
•Consult the dealer or an experienced radio/TV technician for help.
You may find helpful the following booklet, prepared by the FCC: Interference Handbook. This
booklet is available from the U.S. Government Printing Office, Superintendent of Documents,
Washington, DC 20402-9325.
WARNING Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment and void the manufacturer’s
warranty.
Certification This device has been tested and complies with the requirements of:
UL 1950
EN60950: Low Voltage Directive Product Safety
FCC Part 15 Class B
EN55022: Radiated and Conducted Emissions B
EN50082-1: Generic Immunity ESD, RF, and Transient Susceptibility
Copyright ©2002 DYMO Corporation. All rights reserved. 11/02
Trademarks LabelMANAGER, LabelMANAGER PC, and LabelMANAGER 400 are registered trademarks of
DYMO Corporation. DYMO is a registered trademark of Esselte Corporation. All other trademarks
are the property of their respective holders.

iii
Contents
Chapter 1
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Installing the LabelMANAGER Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Registering the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
The LabelMANAGER Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ordering Tape Cassettes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Getting Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Chapter 2
Making Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Designing a Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Printing Labels Using Data from Another Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Printing from Other Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Print Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Chapter 3
Service and Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Contacting DYMO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Appendix A
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

iv

1
Chapter 1
Getting Started
DYMO’s LabelMANAGER electronic label printers allow you to quickly print high-quality
permanent labels. The LabelMANAGER PC must be connected to your computer for you to design
and print labels. The LabelMANAGER 400 has a built-in keyboard allowing you to use it as a
stand-alone label printer in addition to attaching it to your computer. The LabelMANAGER 400
also gives you the option of automatically cutting each label after printing.
With the LabelMANAGER software, you can create labels that include borders, graphics,
formatted text, barcodes, and date and time stamps. You can even print labels horizontally or
vertically. When you save your label designs on your computer, you can use them over and over
again.
The LabelMANAGER software also supports multi-label printing with the Smart Paste and Merge
Print from Database commands. The Smart Paste feature allows you to print labels by copying
multiple entries from a word processor, spreadsheet, or other type of program. Merge Print from
Database allows you to print labels from data in your favorite database program.
Installing the LabelMANAGER Software
In addition to this User Guide, the LabelMANAGER printer is shipped with a Quick Start card.
Follow the instructions in the Quick Start card to install the hardware and software.
Registering the Software
The first time you start the LabelMANAGER application, you are asked to register the software.
We highly recommend that you register your LabelMANAGER software so that you will receive
customer support, information on product updates, and special announcements from DYMO.
If you choose not to register the software at this time, you will be prompted the next several times
you start the program. You can register the software at any time by selecting Register Now from
the Help menu.
To register the software
1Select Register Now from the Help menu.
The Welcome dialog box appears.
2Click Register Now.
The Registration Wizard appears.
3Complete all of the required fields on the registration form and click Next. Required fields are
labeled in bold type.
4Answer the questions presented on the next two screens and click Next.
The Registration dialog box appears.
5Choose to register over the Internet or print the registration form for mail or fax registration.

Getting Started
2
If you choose to register over the Internet, wait a few seconds while your information is
transmitted to DYMO.
To register by mail or fax, click Print to print the completed registration form, and mail or fax
the form to the location printed on the form.
The LabelMANAGER Window
The LabelMANAGER software is easy to learn because the main window consists of menus and
toolbars similar to those of popular word processing programs.
This section summarizes the commands available to you. For more detailed information about a
particular command, refer to the Help.
To start LabelMANAGER
➤Select Start > Programs > LabelMANAGER > LabelMANAGER.
The LabelMANAGER main window is displayed.
File Menu The following commands are available from the File menu.
Standard Toolbar
Formatting Toolbar
Tape Settings Toolbar
Text Area
Rulers
Toolbar
Icon Menu Command Description
New Clears the label text. If the label has been modified, prompts you to save the
changes.
Open Displays the Open File dialog box to open a saved label file. If the current
label has been modified and not saved, prompts you to save the changes.
Save Saves the current label to disk.
Save As Allows you to name the label prior to saving.
Merge Print
from Database Allows you to print labels directly from a .txt or .csv file.
Printer Setup Displays the Printer Setup dialog box allowing access to the driver
properties.
Print Prints the current label. The menu command displays a dialog box asking
how many copies to print.
Change Printer Allows you to choose your printer if more than one LabelMANAGER
printer is installed.
Exit Exits the program. If the current label has not been saved, prompts you to
save the changes.

TheLabelMANAGERWindow
3
Edit Menu The following commands are available from the Edit menu.
Insert Menu The following commands are available from the Insert menu.
Toolbar
Icon Menu Command Description
Undo Undoes the last action.
Redo Redoes the last action after an Undo.
Cut Cuts the selection to the clipboard.
Copy Copies the selection to the clipboard.
Paste Pastes the clipboard contents onto the label.
Smart Paste Performs a multi-label paste. See “Printing Labels Using Data from Another
Program” on page 12.
Select All Selects the entire contents of the label.
Zoom Zooms in or out on the current label.
Options Displays the Options dialog box.
Toolbar
Icon Menu Command Description
Symbol Displays the Insert Symbol dialog box. See “Adding Special Characters” on
page 7.
Date &Time Displays the Insert Date and Time dialog box. See “Adding a Date and Time
Stamp” on page 9.
Picture Allows you to insert a picture from the clipboard or from a file. See “Adding
Graphics” on page 10.
Barcode Allows you to add a barcode and it’s associated text to the label. See "Adding
a Barcode" on page 10.

Getting Started
4
Format Menu The following commands are available from the Format menu.
Help Menu The following commands are available from the Help menu.
Ordering Tape Cassettes
The LabelMANAGER printers use DYMO D1 tape cassettes. The tape cassettes are available in
1/4” (6 mm), 3/8” (9 mm), 1/2” (12 mm), 3/4” (18 mm), and 1” (24 mm) widths, and come in a
variety of colors.
For a complete list of D1 tapes and the names of dealers who sell the tapes, visit the DYMO Web
site at www.dymo.com or call DYMO Sales. See “Contacting DYMO” on page 19.
Getting Help
The LabelMANAGER software includes extensive Help. At times in this manual, you will be
directed to the Help for more detailed discussion or instructions on various topics.
To access the Help
1Select Contents or Help Index from the Help menu.
2Select the topic you want to read about.
The Help can also be accessed by pressing F1 in most windows and dialog boxes to display
context-sensitive help.
Toolbar
Icon Menu Command Description
Font Allows you to apply a font to the selected text.
Borders Allows you to add a border around the contents of the label and may reduce the
size of the text and graphics. See “Adding Borders” on page 7.
Tabs Allows you to set tabs.
TapeCassette
Color Allows you to select the tape cassette color combinationcurrently in the printer to provide optimal print quality. See “Tape Cassette Color Setting” on page 16.
Toolbars Allows you to show or hide the Standard, Formatting, and Tape Settings
toolbars.
Toolbar
Icon Menu Command Description
Contents Displays the Help Table of Contents.
Help Index Displays the Help Index.
Register Now Displays the Electronic Registration page.
About Displays the current version of the software.

5
Chapter 2
Making Labels
The LabelMANAGER printer can print text on your labels in a variety of fonts, sizes, and styles.
You can add borders, graphics, special characters, and barcodes. You can also add a date and time
stamp to your labels.
This chapter gives you an overview of creating and printing labels using the LabelMANAGER
software. For more information on any of these features, refer to the Help.
Designing a Label
The instructions in the Quick Start card showed you how to print your first label. In this section, we
will show you how to print a label for a file folder tab using the LabelMANAGER software. You
can format the label text and then save the label for future use.
When designing a label, the first items to consider are the width of the label tape onto which you
will print and the length of the area where you will place the label. For this example, we will create
a label that will fit on a file folder tab. The total label length must be no more than 3 1/2” (8.5 cm)
and we will print on label tape with a width of 1/2” (12 mm).
To create a label
1Start the LabelMANAGER application.
The main window appears.

Making Labels
6
2Select 1/2” (12 mm) from the Tape Width pull-down menu.
The text area of the main window changes in size based on the tape width you select.
3Select Fixed At and enter 3.50 (8.5 cm) in the Label Length Fixed At text box.
Notice that the size of the input area changes on the ruler.
4Type 2002 Annual Budget Projections in the main window.
As the line of text becomes too long for a fixed width label at the current font size, the font size
will automatically decrease to fit the text on one line.
5To center the text, click .
6Click or select Save from the File menu.
The Save File dialog box appears.
7Type a name for the label and click Save.
The label is saved to your hard disk with a .dlm extension automatically added to the file name.
Now let’s print the label.
8Click or select Print from the File menu.

Designing a Label
7
Now that you have created and saved your label, the following sections will introduce additional
features you can use to customize your labels.
Additional Formatting Features
To further customize your labels, you can add borders, symbols, graphics, barcodes, and even date
and time stamps. You can also choose to print the label vertically.
Adding Borders
You can choose to add one of several pre-defined borders to your label. When you add a border, it
surrounds the text and may cause the text to decrease in size.
To add a border
1Place the cursor anywhere on the label.
2Select a border style from the Borders pull-down menu.
The selected border surrounds the text. If necessary, the font size of the text is decreased to fit
the label.
Adding Special Characters
You can choose to add a special character or symbol to the label.
To add a special character
1Place the cursor at the point on the label where you want the character to appear.
2Click on the Standard toolbar or select Symbol from the Insert menu.

Making Labels
8
The Symbol dialog box appears.
3Choose the font that contains the special character you wish to insert from the Font pull-down
menu.
The Symbol, Dingbats, and Wingdings fonts contain many unique characters you can add to
your labels.
4Select the symbol you wish to insert and click Insert.
5Click Close to close the Symbol dialog box.
The character you selected appears on the label in a size that matches the text font size.
Adding Special Font Effects
In addition to the standard font styles (bold, italic, underline, and strikeout), you can make your text
stand out using a shadow or outline style. With the outline style, you choose the fill pattern.
To add a shadow effect to your text
1Highlight the text on your label that you wish to appear with a shadow effect.
2Select Font from the Format menu. The Font dialog appears.
3Select Shadow under Effects and click OK.
The highlighted text now appears on the label with a shadow effect.

Designing a Label
9
To add an outline effect to your text with a fill pattern
1Highlight the text on your label to which you wish to apply an outline effect.
2Select Font from the Format menu. The Font dialog box appears.
3Select Outline under Effects.
4Select a fill pattern from the Fill Pattern drop-down menu.
5Click OK. The highlighted text now appears on the label with an outline effect.
Adding a Date and Time Stamp
You can choose to add a date and/or time stamp to the label. The date and time is entered as text and
will be the actual system date and time when you added the stamp to the label. For example, if
today’s date is 24 Oct 2002 and you add the date to a label design today, save the label, and then
open it tomorrow, 24 Oct 2002 will still appear on the label.
To add a date and time stamp
1Place the cursor at the point on the label where you want the date and/or time stamp to appear.
2Click on the Standard toolbar or select Date & Time from the Insert menu.
The Date and Time dialog box appears.
3Select the date and/or time format you wish to insert and click OK.

Making Labels
10
The date and/or time appears on the label in the format you selected.
Adding Graphics
You can add a graphic to your label from the clipboard or from a file. If the graphic is in a file, the
format can be BMP, JPG, PCX, PNG, TIF, WMF, or EMF. When inserted on the label, the graphic
will be scaled automatically to the size of the surrounding text while maintaining the aspect ratio.
To add a graphic from the clipboard
1Copy the graphic to the clipboard from another application.
2Place the cursor at the point on the label where you want the graphic to appear.
3Click on the Standard toolbar or select Paste from the Edit menu.
The graphic appears on the label at the cursor position.
To add a graphic from a file
1Place the cursor at the point on the label where you want the graphic to appear.
2Click on the Standard toolbar or select Graphic from the Insert menu.
The Open File dialog box appears.
3Select the graphic file you wish to insert and click Open.
The graphic you selected appears on the label.
Adding a Barcode
You can choose to add a barcode to your label. This feature can be very useful, for example, if you
are labeling inventory items that will be scanned with a barcode reader. You can choose to print the
barcode with or without the human-readable text.
To add a barcode
1Place the cursor at the point on the label where you want the barcode to appear.

Designing a Label
11
2Click on the Standard toolbar or select Barcode from the Insert menu.
The Barcode Settings dialog box appears.
3Type the text you wish displayed as a barcode in the Data field.
4Select the type of barcode from the Symbology drop-down menu.
5Select whether you want the actual text to appear above the barcode, below the barcode or not
at all under Human Readable Text.
6If you selected above or below, click the Font button to choose the font for the text.
7Select the size of the barcode under Barcode Size.
8Click OK to insert the barcode on the label.
The barcode is placed on the label as a single object. To remove the barcode, you can use the
backspace key or highlight the barcode and select .
Printing Vertically
You can print your label vertically, for example, to be placed on the spine of a binder or a video
tape. When you print vertically, the text on your label is reformatted to fit in a single column on the
label. You may wish to center the text on the label as well.
To print vertically
1Click in the Vertical Label check box on the Formatting toolbar to select Vertical.
A warning dialog box appears informing you that the text will be reformatted.

Making Labels
12
NOTE If the contents of the label are too long to fit vertically on a fixed width label, the excess
content is truncated. This action cannot be undone once you click Yes.
2Click Yes.
The text of your label is now displayed in a single vertical column.
Printing Labels Using Data from Another Program
LabelMANAGER includes two commands that allow you to print labels from other programs:
Smart Paste and Merge Print from Database. The Smart Paste command allows you to print
multiple labels from a list created in a word processing, spreadsheet, or other similar program.
Merge Print from Database allows you to print labels from a text or Comma Separated Value (CSV)
file exported from a database program.
Spreadsheet Text
When copying and pasting rows of text from a spreadsheet program using Smart Paste, each row is
treated as a separate label and each cell in the row is treated as a separate line on the label.
For example, the rows in the following spreadsheet:
will print two three-line labels: one for DYMO and one for Esselte.
Text File
Many programs can create a text file, such as a text editing program, a database application, and so
on. When you export text from a database, you usually create a delimited file with each entry
separated by comma or tab characters, and a carriage return/line feed at the end of each entry.
Both the Smart Paste and the Merge Print from Database commands recognize the delimiter
characters and will insert a line break on the label. When a comma is used as a delimiter, make sure
the text that contains any commas that you want to print on the label is enclosed in quotation marks.
The carriage return/line feed will start a new label.
NOTE The separator character may be different for countries other than the US. When using Smart
Paste, the list separator character is based on the Windows list separator (or regional setting)
being used.
For example, the following lines of text (delimited using commas):
DYMO Corp., 44 Commerce Road, “Stamford, CT 06902”
Esselte, 48 South Service Road,“Melville, NY 11471”
DYMO Corp.
44 Commerce Road
Stamford, CT 06902
Esselte
48 South Service Road
Melville, NY 11471

Printing Labels Using Data from Another Program
13
will print two three-line labels: one for DYMO and one for Esselte.
In another example, the following three lines of text are printed as three two-line labels:
Multi-Line Text from a Word Processor
When copying text from a word processor, you will typically have multi-line text. In this case, the
text for each label is separated by either a single blank line or a carriage return/line feed.
If a blank line is contained in the text, Smart Paste reads the text as multiple labels separated by a
single blank line. If no blank line is found, the text is read as multiple, one-line labels.
For example, the following two addresses are separated by a single blank line and Smart Paste will
print two three-line labels.
However, the following three lines of text contain no blank lines. So, Smart Paste will print three
one-line labels.
Printing Multiple Labels Using Smart Paste
This section explains how text copied from different sources is turned into labels using the Smart
Paste command. When you use Smart Paste to print multiple labels, the labels will be formatted
using the font, size, and style currently selected for the label.
DYMO Corp.
44 Commerce Road
Stamford, CT 06902
Esselte
48 South Service Road
Melville, NY 11471
Pencils
3 for $1.00
Pencils, 3 for $1.00
Pens, $0.50 each
Erasers, $1.00
Pens
$0.50 each
Erasers
$1.00
DYMO Corp.
44 Commerce Road
Stamford, CT 06902
Esselte
48 South Service Road
Melville, NY 11471
Erasers
Pencils
Pens

Making Labels
14
To print multiple labels
1Copy the text you wish to print as labels to the clipboard.
2From the Tape Settings toolbar, select the tape width from the Tape Width pull-down menu.
3Select the formatting for the labels from the Formatting toolbar.
For example, you can change the font, size, and the horizontal position on the label.
4Select Smart Paste from the Edit menu.
A dialog box appears telling you how many labels will be printed.
5Click OK. The labels begin printing.
Printing Multiple Labels Using Merge Print from Database
This section explains how to print labels by merging data exported from a database program. When
you print labels using this command, the labels will be formatted using the font, size, and style
currently selected for the label.
To print multiple labels from a database file
1Export the records you wish to print as labels to a CSV or text file from your database
program.
2From the Tape Settings toolbar, select the tape width from the Tape Width pull-down menu.
3Select the formatting for the labels from the Formatting toolbar.
For example, you can change the font, size, and the horizontal position on the label.
4Select Merge Print from Database from the File menu. The File Open dialog box appears.
5Navigate to and open the file you exported from your database.
A dialog box appears telling you how many labels will be printed.
6Click OK. The labels begin printing.
Printing from Other Applications
The LabelMANAGER installation wizard installs a standard Windows printer driver on your
computer so the LabelMANAGER printer will appear in your list of printers. This printer can be
used to print directly from other applications, such as Microsoft Word or Access, in the same
manner as you would use any other printer.

Printing from Other Applications
15
To successfully print to a LabelMANAGER printer, you need to set the correct page size,
orientation, and margins for the tape cassette currently in the printer. Table 1 gives the paper size
and margin settings for each of the label sizes supported by the LabelMANAGER printers.
This section shows you how to print from within Microsoft Word to a LabelMANAGER printer.
However, printing from applications other than Word follows the same basic steps.
To print from Microsoft Word
1Type the text to be printed into a Microsoft Word document.
2Select Print from the File menu.
The Print dialog box appears.
3Select DYMO LabelMANAGER (PC or 400) from the list of printers, if not already selected,
and click Close.
4Select Page Setup or Print Setup from the File menu.
The Page Setup dialog box appears.
5On the Margins tab, enter the margin values for the top, bottom, left, and right margins based
on the labels you have loaded in the printer.
Refer to Table 1 for the correct settings.
6Click the Paper Size tab.
7Select the label size you have loaded in the printer from the Paper size drop-down list.
Table 1. Label Size and Margin Settings
Paper Name Paper
Height Paper Width Top Margin Bottom Margin Left Margin Right Margin
Address Label 1”
(24 mm) 3.5” (89 mm) 0.23” (5.8 mm) 0.24” (6.1 mm) 0.4” (10.2 mm) 0.39” (9.9 mm)
Large Pendaflex 0.5”
(12 mm) 3.5” (89 mm) 0.09” (2.3 mm) 0.10” (2.6 mm) 0.4” (10.2 mm) 0.39” (9.9 mm)
Small Pendaflex 0.5”
(12 mm) 3.5” (89 mm) 0.09” (2.3 mm) 0.10” (2.6 mm) 0.4” (10.2 mm) 0.39” (9.9 mm)
1/3 File 0.5”
(12 mm) 3.5” (89 mm) 0.09” (2.3 mm) 0.10” (2.6 mm) 0.4” (10.2 mm) 0.39” (9.9 mm)
1/5 File 0.5”
(12 mm) 2” (51 mm) 0.09” (2.3 mm) 0.10” (2.6 mm) 0.4” (10.2 mm) 0.39” (9.9 mm)
6 mm Label 0.25”
(6 mm) 3.5” (89 mm) 0.04” (1 mm) 0.04” (1 mm) 0.4” (10.2 mm) 0.39” (9.9 mm)
9 mm Label 0.375”
(9 mm) 3.5” (89 mm) 0.03” (1 mm) 0.04” (1 mm) 0.4” (10.2 mm) 0.39” (9.9 mm)
12 mm Label 0.5”
(12 mm) 3.5” (89 mm) 0.09” (2.3 mm) 0.10” (2.6 mm) 0.4” (10.2 mm) 0.39” (9.9 mm)
19 mm Label 0.75”
(19 mm) 3.5” (89 mm) 0.11” (2.8 mm) 0.11” (2.8 mm) 0.4” (10.2 mm) 0.39” (9.9 mm)
24 mm Label 1”
(24 mm) 3.5” (89 mm) 0.23” (5.8 mm) 0.24” (6.1 mm) 0.4” (10.2 mm) 0.39” (9.9 mm)

Making Labels
16
The width and height values should now match the values for that label size shown in Table 1.
8Select Landscape under Orientation and click OK.
9Click to print the label.
Print Settings
This section discusses several printer settings that may optimize your printing.
Tape Cassette Color Setting
The LabelMANAGER printer adjusts its print settings based on the color of the label tape. To
optimize the print quality, make sure you set the tape cassette color setting to match the color of the
tape in the printer.
To set the tape cassette color
1Select Tape Cassette Color from the Format menu.
A list of possible tape color combinations appears.
2Select the tape color combination that matches the tape cassette in the printer.
Depending upon the selection you make, the background color in the main window may change so
that you get a better idea of how your printed label will look.
Chain Printing
When printing multiple labels, the chain printing feature will automatically print a dashed cut-line
between each label to indicate where each label should be cut.
For the LabelMANAGER PC printer, chain printing is always turned on. The LabelMANAGER
400 gives you the option of chain printing or automatically cutting each label after printing.
To change the chain print setting
1Select Options from the Edit menu.
DYMO Corp.
44 Commerce Road
Stamford, CT 06902
Esselte
48 South Service Road
Melville, NY 11471