Dynex DX-WD1202 User manual

ASSEMBLY INSTRUCTIONS
DX-WD1202
Corner TV Stand
Safety information and specifications ............2
Tools needed............................................................3
Package contents ...................................................3
Assembly instructions...........................................6

2DX-WD1202
Need help? Call 800-305-2204
Safety information and specifications
Warnings
• Do not let children climb on your stand or play near it. The stand may tip over causing the TV or stand to
injure someone.
• When placing items on the shelves or the top of the stand, load the bottom shelf first and work up to the top
of your stand.
• Do not overload the shelves. They may break.
• Do not move your stand with items on the top or shelves. Your stand may tip over and injure someone. Before
you move your stand, unload starting with the top of your stand and working to the bottom shelf.
• Do not push your stand to move it. With the help of a second person, lift your stand to move it.
CAUTION:
This stand’s work surface is intended only for use
with a product not weighing more than 95 lbs.
(43.09 kg) and accommodates most 37" and
some 42" flat-panel TV’s or 27" CRT TV’s with dimensions
that will permit the TV to sit evenly on the stand. Using with
other products, including products that weigh more than
the maximum weight allowed, may result in instability,
which may cause possible injury.
Maximum weight: 95 lbs. (43.09 kg)
Maximum screen size: Most 37" and some 42" flat-panel TV’s or
27" CRT TV’s
Weight capacity (top of stand): 95 lbs. (43 kg)
Weight capacity (middle shelf): 25 lbs. (11 kg) per side
Weight capacity (total lower shelf): 40 lbs (18 kg)
Overall dimensions: W × H × D
39.25" x 11.38" × 19.5" (99.69 × 28.9 × 49.53 cm)
Top of stand: W ×H
39.25" × 19.5" (99.69 × 49.53 cm)
Usable middle shelf: W × H × D
17.38" × 5.75" × 17" (44.15 × 14.6 × 43.18 cm) per side
Usable lower shelf: W × H × D
16.5" × 8" × 16.75" (4.9 × 20.3 × 42.55 cm)
19.5" (49.53 cm)
39.25" (99.69 cm)
11.38" (28.9 cm)
37.5" (95.88 cm)

3
DX-WD1202
Need help? Call 800-305-2204
Packagecontents
Package contents: hardware
Note: You may receive extra hardware with your new TV stand.
Make sure you have all the hardware necessary to assemble your new TV stand:
Tools needed
Hammer
No. 2 Phillips screwdriver
Flatblade screwdriver
Caution: Do not
use an electric drill
or screwdriver
Shim
Label Hardware Qty.
Q30
R22
S8
T1
U1
V4
Hidden cam
Cam dowel
Cam screw
Foot
Foot base
Hinge
Label Hardware Qty.
W2
X2
Y2
AA 2
BB 1
Washer
Pull
Bumper card
Hole cover
Warning
label

4DX-WD1202
Need help? Call 800-305-2204
Package contents: hardware (continued)
Using a screw that is too long will cause damage to your stand. Before beginning assembly, separate
each type of screw. Carefully study the screw table below. You can use the ruler at the bottom of the
screw table to measure screws. Pay close attention to the color of each screw.
Letter Description Qty.
CC 4
DD 4
EE 3
FF 8
GG 4
HH 8
II 8
JJ 2
KK 33
Black 2 1/2" (63.5 mm) large head screw
Black 1 7/8" (47.75 mm) flat head screw
Brown 1 1/2" (38.1 mm) flat head screw
Black 9/16" (14.22 mm) flat head
Black 9/16" (14.22 mm) pan head screw
Black 1/2" (12.7 mm) flat head screw
Brown 7/16" (11.17 mm) large head screw
Silver 1/4" (6.35 mm) machine screw
Nails
10 20 30 40 50 60 70 80 90 100mm
1234in

5
DX-WD1202
Need help? Call 800-305-2204
Package contents: parts
AEnd (2)
EBottom (1) FShelf (1)
BUpright (1) C Lower upright (1) DTop (1)
GBack (1)
H Door (2) I Right front and left rear leg (2)
JLeft front and right rear leg (2) KExtension (2) LStop molding (1)
MTop molding (1) NBase (1) OTop rail (2) PBottom rail (2)

6DX-WD1202
Need help? Call 800-305-2204
Assembly instructions
Step1:
Assemble your stand on a carpeted floor or on the empty carton to avoid scratching your stand or the floor.
Push thirty hidden cams (Q) into the ends (A), uprights (Band C), top (D), bottom (E), shelf (F), and one set of
legs (Iand J). Then, insert twenty-two cam dowels (R) into the hidden cams. Do not insert cam dowels into
the hidden cams on the end of (A) as indicated in the illustration.
You’ll n ee d:
Do not insert cam dowels
into these edges.
Arrow
Do not tighten the hidden cams in this step.
R(22)Q(30)

7
DX-WD1202
Need help? Call 800-305-2204
Tightening hidden cams
In the remaining steps, use these illustrations for instructions on tightening hidden cams.
Warning: Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are not
completely tightened will loosen, and parts may separate.
A hidden cam (Q) has an arrow. When you insert the hidden cam, make sure that the arrow points toward the
hole in the side of the part you are inserting it into.
You’l l nee d:
Arrow Make sure that you turn the
hidden cam 210°. Note the
position of the arrow on the
hidden cam.
Arrow
In the illustration below,
the hidden cam has not
been tightened enough.
210°
Flatblade screwdriver

8DX-WD1202
Need help? Call 800-305-2204
Step 2:
Screw two cam screws (S) into each of the legs (two Iand two J).
Place the ends (A) flat with the side with the hidden cams facing up.
Make sure that the sides of the legs with the hidden cams are toward the ends (A).
Insert the cam screws on one of the legs (I) into one of the ends (A) and cam screws on one of the legs (J) into
the opposite side of the other end (A).
Tighten the four hidden cams. See “Tightening hidden cams” on page 7.
You’ll n ee d:
Surface with
hidden cams
Leg with
hidden cams
Leg with
hidden cams
S (8)Flatblade screwdriver

9
DX-WD1202
Need help? Call 800-305-2204
Step 3:
Carefully turn the ends (A) over so the side without the hidden cams is facing up.
Use a Phillips screwdriver to screw eight black 9/16" flat head screws (FF) (four per end) into the ends (A) until
the shoulders of the screws rest on the surface of the ends. Do not screw the screws in all the way.
Align the groove on a top rail (O) over the top screw head on one of the ends (A), then slide the rail over the
other screw head. Make sure that the ends of the rail are flush with the edges of the end. Repeat to attach the
other top rail (O) to the other end (A).
Align the groove on a bottom rail (P) over the bottom screw head on one of the ends (A), then slide the rail
over the other screw head. Make sure that the ends of the rail are flush with the edges of the end. Repeat to
attach the other bottom rail (P) to the other end (A).
You’ll ne ed :
Apply pressure with your hand as you
guide the rails over the screws on the
ends.
Screw head
FF (8)Phillips screwdriver

10 DX-WD1202
Need help? Call 800-305-2204
Step 4:
Carefully turn the ends over so the sides with the hidden cams face up.
Attach the unattached leg (I) to the left end (A) and the unattached leg (J) to the right end (A). See Step 2 for
instructions.
Insert a hole plug (AA) into the holes on the legs (Iand J) that you just attached.
You’ll n ee d:
This end will now be
referred to the left end.
This end will now be
referred to the right end.
Flatblade screwdriver AA (2)

11
DX-WD1202
Need help? Call 800-305-2204
Step 5:
Fasten the stop molding (L) to the top (D). Use a flatblade screwdriver to tighten the four hidden cams. See
“Tightening hidden cams” on page 7.
You’l l nee d:
Unfinished
surface
Unfinished surface
Rounded edge
Arrow
210°
Flatblade screwdriver

12 DX-WD1202
Need help? Call 800-305-2204
Step 6:
Fasten the upright (B) and the left end (A) with the leg (J) to the top (D) and stop molding (L). Use a flatblade
screwdriver to tighten the five hidden cams (two on the upright (B), two on the left end (A), and one on the
leg (J)). See “Tightening hidden cams” on page 7.
You’ll ne ed :
Surface without
hidden cams
Finished edge
Arrow
210°
Flatblade screwdriver

13
DX-WD1202
Need help? Call 800-305-2204
Step 7:
Fasten the shelf (F) to the left end (A). Use a flatblade screwdriver to tighten the two hidden cams. See
“Tightening hidden cams” on page 7.
Fasten the shelf (F) to the upright (B). Use a Phillips screwdriver and two black 1 7/8" flat head screws (DD).
Fasten the lower upright (C) to the shelf (F). Use a flatblade screwdriver to tighten the two hidden cams.
You’ll need:
finie
ficie sin acabado
Chant fini
Surface without
hidden cams
Finished
edge
Unfinished
surface
Arrow
210°
Flatblade screwdriver Phillips screwdriver DD (2)

14 DX-WD1202
Need help? Call 800-305-2204
Step 8:
Fasten the bottom (E) to the left end (A). Use a flatblade screwdriver to tighten the two hidden cams. See
“Tightening hidden cams” on page 7.
Fasten the bottom (E) to the lower upright (C). Use a Phillips screwdriver and two black 1 7/8" flat head
screws (DD).
Slide the base (N) onto the notched edge of the bottom (E) so that the edge of the base is flush with the leg
on left end (A).
You’ll need:
Unfinished surface
Notched edge
Arrow
210°
Flatblade screwdriver Phillips screwdriver
DD (2)

15
DX-WD1202
Need help? Call 800-305-2204
Step 9:
Fasten the right end (A) with the leg (I) to the top (D), bottom (E), shelf (F), and stop molding (L). Use a
flatblade screwdriver to tighten the seven hidden cams: A(2), E(2), F(2), and I(1). See “Tightening hidden
cams” on page 7.
Fasten the top molding (M) to the stop molding (L). Use a Phillips screwdriver and three brown 1 1/2" flat
head screws (EE).
Fasten the extension blocks (K) to the bottom (E). Use a Phillips screwdriver and four black 2 1/2" large head
screws (CC).
You’ll n ee d:
Arrow
210°
Flatblade screwdriver Phillips screwdriver
EE (3) CC (4)

16 DX-WD1202
Need help? Call 800-305-2204
Step 10:
With the top of the unit facing down, fasten the foot base (U) to the extension block (K). Use a Phillips
screwdriver and four black 9/16" pan head screws (GG). Then, push the foot (T) into the foot base (U).
Note: Turn the foot (T) for adjustments. The foot should not extend beyond the bottom edge of the base (N).
You’ll need:
Phillips screwdriver GG (4)

17
DX-WD1202
Need help? Call 800-305-2204
Step 11:
Carefully turn the unit so the front is facing down, then fasten the back (G) to the legs (Iand J). Use a Phillips
screwdriver and eight brown 7/16" large head screws (II).
Fasten the remaining back (G) to your stand using 33 nails (KK).
Note: Be sure to tap the nails into the holes that line up over the shelf (F). Perforations have been provided for access through
the back. Carefully cut out the holes needed.
You’ll need:
These holes must line
up over shelf (D). Caution: Do not stand
your stand upright
without the back
fastened. Your stand may
collapse.
Phillips screwdriver II (8)KK (33)
Hammer

18 DX-WD1202
Need help? Call 800-305-2204
Step 12:
Fasten the hinges (V) to the doors (H). Use a Phillips screwdriver and eight 1/2" flat head screws (HH) (two for
each hinge).
You’ll ne ed :
Phillips screwdriver HH (8)

19
DX-WD1202
Need help? Call 800-305-2204
Step 13:
Carefully turn the unit so the left end is facing down, then fasten one of the doors (H) to the left end (A). Use
a Phillips screwdriver and the screws in the hinges.
Note: You may need to loosen the mounting screw to slide the hinge part way out of the slot. Retighten the screw before you
mount the hinge to the end.
Carefully turn the unit so the right end is facing down, then fasten the other door (H) to the right end (A). Use
a Phillips screwdriver and the screws in the hinges.
Carefully turn the unit so it is right side up.
Align a pull (X) with the screw hole in the middle of the door (H). Place a washer (W) over the screw hole on
the back of the door, then insert a silver 1/4" machine screw (JJ) through the washer and into the pull screw
hole. Tighten the screw. Repeat this step for the other door.
Peel two bumpers from the bumper card (Y) and stick them on the inside of the door where the door comes
in contact with the lower upright (C). Repeat this step for the other door.
You’l l nee d:
Mounting screw
Phillips screwdriver W(2) X(2) Y(4) JJ (2)

20 DX-WD1202
Need help? Call 800-305-2204
Step 14:
You may need to adjust the doors to make them fit correctly.
To adjust the doors from side to side (horizontal), loosen the mounting screw several turns, then turn the
horizontal adjusting screw in or out. Tighten the mounting screw after making adjustments.
To adjust the doors up and down (vertical), loosen both vertical adjustment screws. Move the doors up or
down to the best location. Tighten the screws after making adjustments. You can use a shim to help hold the
door in place.
To adjust the doors in or out (depth), loosen the mounting screw one turn and move the doors in or out, as
needed. Tighten the mounting screw after making adjustments.
You’ll need:
Horizontal
adjusting screw Mounting
screw (depth)
Vertical
adjusting screws
Shim
Phillips screwdriver
Shim