Dyson Airblade Wash+Dry User manual

The Dyson Airblade Wash+Dry hand dryer should be cleaned daily.
Follow these 3 simple steps to ensure the machine performs
to its best and remains hygienic.
Keep it clean
Important information
Most professional cleaning chemicals
can be used.
Using the wrong cleaning method or
product may invalidate the warranty.
All cleaning chemicals should be
used exactly as indicated by the
manufacturer’s instructions
(including appropriate dilution).
Any chemicals intended for use should
first be tested on an inconspicuous
area to confirm suitability.
Aside from cleaning chemicals, care
should be taken to avoid any harmful
fluids from coming into contact with
the product, in particular oils and
alcohol-based products.
Do not pressure wash the machine.
The following are some that are
harmful to the machine.
Wipe sensors using a soft
cloth and non-abrasive
cleaner then place
cleaning cap over sensors
to prevent activation.
Clean all tap surfaces,
sink, mirror and any walls or
counter tops. When complete
REMEMBER to remove
cleaning cap.
REGULARLY clean air inlets
on base of motor bucket
(under sink). Ensure plughole
in sink is free from blockages
so water can drain freely.
For further information please contact Dyson.
AU: 1800 426 337 [e-mail]
NZ: 0800 397 667 [e-mail]
21 3
DO NOT USE
Alcohol-acid mixes
Alcohol
Solvent/oil-based mixes
Quaternary ammonium
Alkali-bleach mixes
Foaming ingredients
Bleach or abrasive cleaners

For further information please contact Dyson.
AU: 1800 426 337 [e-mail]
NZ: 0800 397 667 [e-mail]
Requirement Suggested method Comments
Routine cleaning
of light soiling.
Soap, detergent or dilute (1%) ammonia
solution in warm clean water. Apply with
a clean sponge, soft cloth or soft-fibre brush
then rinse in clean water and dry.
Satisfactory on most surfaces.
Fingerprints. Detergent and warm water, alternatively,
hydrocarbon solvent.
Proprietary spray-applied polishes available
to clean and minimise remarking.
Oil and grease marks. Hydrocarbon solvents (methylated spirit,
isopropyl alcohol or acetone).
Stubborn spots, stains and light
discolouration. Water marking.
Light rust staining.
Mild, non-scratching creams and polishes.
Apply with soft cloth or soft sponge and rinse
off residues with clean tap water and dry.
Drying marks may be avoided using an air
blower or wiping with clean disposable wipes.
Avoid cleaning pastes with abrasive additions,
wire wool or hard objects such as knife blades.
These can create surface scuffs and scratches or
even cause rust marks. Suitable cream cleansers
are available with soft calcium carbonate
additions. Do not use chloride solutions.
Dyson Airblade Wash+Dry hand dryer cleaning
requirements and suggested cleaning methods
Water supply cleanliness
and biological growth
Automatic duty flush
Bacteria can grow in
inactive water systems
In some commercial locations water taps
can go unused for weeks. Water within
the system can stagnate, leading to the
growth of bacteria.
Re-engineered with
automatic duty flush
One way to counter bacteria proliferation
is to flush water outlets before water can
stagnate. The Dyson Airblade Wash+Dry
hand dryer has re-engineered software
to do this for you.
How it works
If water flow isn’t activated for 24 hours,
the water solenoid will open automatically.
Water will be flushed through for
60 seconds, expelling standing
water in the system.
In some countries there are regulations
or guidelines that require temperature
controlled water supply systems
(such as that supplied to the Dyson
Airblade Wash+Dry hand dryer)
to be subjected to regular cleaning
to minimise any biological growth.
To enable you to meet these regulations,
the Dyson Airblade Wash+Dry hand dryer
has been designed and tested to withstand
internal cleaning both with hot water up
to 95°C and with sodium hypochlorite
at a concentration of 0.45%
When carrying out internal cleaning
of the Dyson Airblade Wash+Dry hand
dryer, please be aware of any safety
considerations when using hot water
or chemicals. Dyson will not be responsible
for any injury caused by this process.
Dyson is unable to advise regarding the
details of the cleaning you should carry
out because this will be specific both to
the applicable regulations and to your
water supply system.