Dyson Airblade wD05 User manual

350mm minimum
385mm minimum
300mm minimum
100mm minimum
200mm maximum
350mm minimum
385mm minimum
300mm minimum
100mm minimum
200mm maximum
350mm minimum
385mm minimum
300mm minimum
100mm minimum
200mm maximum
PRE-INSTALLATION INFORMATION
Sink dimensions (All internal measurements unless otherwise stated)
Fig.1 Width of sink minimum: 350 mm, Front to back of sink minimum: 300 mm
Fig.2 Maximum depth of sink for Tall Neck Tap (WD05) only: 200 mm
(External measurement of vessel/pedestal sink.)
Fig.3 Minimum distance from tap centre to top of sink (WD06 only) 100 mm.
Front edge of sink (all types – pedestal, recessed, slab) to wall minimum 385 mm.
Internal depth of sink minimum (for all taps): 100 mm
Tap mounting
The tap stem (measured from the outside diameter) should
be mounted 15-40 mm from the outside edge of the sink.
There should be a minimum of 290 mm between a tap centre
and a side wall. When multiple taps are installed side-by-side,
tap centres should be a minimum of 580 mm apart. This allows
sufficient space for mounting the motor bucket, as well as sufficient
shoulder room for users.
Sink specification guidelines
Using a specially designed test method, Dyson engineers
tested a wide range of sinks to assess their compatibility with
the Dyson Airblade Wash+Dry hand dryer. For recommended
sinks, please contact dyson
AU: 1800 426 337 or NZ: 0800 397 667
Porcelain or brushed metal sinks are ideal.
Sinks with highly polished surfaces should be avoided
e.g. reflective chrome.
Fig.1 Fig.2
Fig.3
350 mm minimum
300 mm minimum
200 mm maximum
100 mm minimum
385 mm minimum

350mm minimum
385mm minimum
300mm minimum
100mm minimum
200mm maximum
350mm minimum
385mm minimum
300mm minimum
100mm minimum
200mm maximum
Soap and locating the soap dispenser
For best user experience, Dyson recommends the use of gel soaps.
The infrared sensing zone for air activation extends along each tap
branch. In order to prevent accidental activation, it’s important to
consider the user’s hand route to the soap dispenser.
The dispenser should be located at least 60 mm outside the width
of the tap, so the user reaches around the side of the branch.
It should also be located at least 60 mm above the branches,
so that the sensors are not activated.
Please note that the user may reach diagonally across for the soap,
so this path must not go through the sensing zone.
Front on view showing
soap dispenser
clear zone
Over head view showing
soap dispenser
clear zone
60 mm60 mm
60 mm
60 mm 60 mm
60 mm
Tap mounting
Do not place the downward facing water sensor of the tap
over a reflective surface, such as the drainage hole. (Fig.4)
For complete instructions, please refer to the printed
installation guide supplied with the machine.
It’s also available online at www.dyson.com.au/hand-dryers/
useful-documents
Fig.4
WD04, WD05 240 mm
WD06 300 mm

X
X
6°
Fig.5
Fig.7
Fig.8
Fig.9
Fig.6
Base to back and front wall transition
The base to back and front wall transition should also be
considered. The back wall should be as close to 90°, and
at as sharp a radius as possible (Fig.7). Curved geometry
is more likely to increase splashback, whereas sloping back
and front wall transitions should be avoided (Fig.8 & 9).
Water drainage
Due to high velocity air and water being in close proximity,
there is a chance of some water and soap dispersion outside
the sink dimensions. To alleviate this effect, we recommend
following the below guidelines.
Base profile
Flat base profile will result in poor drainage leading to high
levels of splashback.
To improve drainage, avoid sinks with a flat base with particular
focus on the immediate area surrounding the drain hole,
minimum 60 mm radius (Fig.5).
Vertical and sharp transition
Vertical and smooth transition
Sloped transition, especially on square or rectangular sinks
Minimum of 6° ramp angle from the edge of the drain hole
of the sink will result in good drainage leading to reduced
levels of splashback (minimum 60 mm radius).
60 mm60 mm
60 mm60 mm

L N
L N
L N
L N
Sink access guidelines
It is recommended that the following guidelines are followed to
ensure there is sufficient access under the sink to allow for servicing
and installation to take place (Fig.10).
Plug hole
Plug holes with the most open aperture are recommended,
whereas grill or perforated type plug holes should be avoided
as they restrict the drainage of soapy water (lather). Do not use
plugs within the plug holes in sinks.
Fig.10 Fi g.11
Mounting the motor bucket (WD04/WD05)
Ensure 100 mm minimum clearance from bottom
of motor bucket to floor/wall.
The motor bucket cannot be mounted upside down
or installed above the sink.
Only the following is advised (Fig.11).
100 mm
100 mm
100 mm
(min)
85 mm
(min)
380 mm (min)
CLEAR ZONE

WD06 metal enclosure assembly
Fig.13
Fig.14 Fig.15
Install
plasterboard.
Install Dyson
Airblade
Wash+Dry
Hand dr yer.
Fig.12
Installing WD06
The WD06 Dyson Airblade Wash+Dry hand dryer is designed
so that the motor unit is located behind a stud wall within a metal
enclosure which is supplied with the Dyson Airblade Wash+Dry
hand dryer (Fig.12). The vertical wall studs must be constructed
so as to allow the metal enclosure to be fitted between them (Fig.13).
One of the horizontal wall studs must be fitted a) so it holds the main
weight of the metal duct and the unit, and b) so it is in the correct
position for the tap stem.
For complete instructions, please refer to the printed
installation guide supplied with the machine.
It’s also available online at www.dyson.com.au/hand-dryers/
useful-documents

For further information please contact Dyson.
AU: 1800 426 337 [e-mail]
NZ: 0800 397 667 [e-mail]
Tools required
To install this unit you will need (4) screws, and appropriate fittings
Torx T15 screw driver – long handle
Electrical drill with 35 mm drill bit
4 wall plugs (check suitability for wall type)
7 mm flat head screwdriver
Flat terminal block screwdriver
37 mm Box spanner
Sharp knife/blade
Pan head screws, 5 mm in diameter, toggle or masonry type
Conduit as per local electrical regulations
Electrical
Input voltage/Frequency: 200-240V 50 & 60Hz
Isolated by switch fuse spur or RCD as appropriate
Current 6.6 A
Cable specification: 3 core PVC 1.5 mm cross sectional area
Local electrical regulations must be adhered
to when installing or repairing the product
Rated power: 1000 W
Operating temperature range: 0° – 40°C
Standby power consumption: Less than 0.5 W
Water operation
Water flow rate: 1.9 l/min normal fitted aerator
4 l/m with low flow aerator supplied with product
Water temperature control: There is no in-built function to change
the temperature of the water. The use of a Thermostatic mixer or
heater (not included) is recommended.
Water pressure required: 1-8 bar
1 ½” BSP isolated valve required for service
Maximum altitude: 2,300 metres
Water supply cleanliness and biological growth
In some countries there are regulations or guidelines that require
temperature controlled water supply systems (such as that supplied
to the Dyson Airblade Wash+Dry hand dryer) to be subjected to regular
cleaning to minimise any biological growth.
To enable you to meet these regulations, the Dyson Airblade Wash+Dry
hand dryer has been designed and tested to withstand internal
cleaning both with hot water up to 95°C and with sodium hypochlorite
at a concentration of 0.45%.
Please refer to specific (market) regulations and water supply system
recommendations for information on cleaning regimes for water supply
cleanliness and biological growth for your country.
When carrying out internal cleaning of the Dyson Airblade Wash+Dry
hand dryer, please be aware of any safety considerations when
using hot water or chemicals. Dyson will not be responsible
for any injury caused by this process.
Abusive testing
The tap has undergone rigorous abusive testing to ensure
that it can withstand substantial forces and impacts typical
of a commercial and public bathroom environment.
If you are connecting a hot and cold water feed
you will need to install a thermostatic mixer.
Water temperature control
If connecting to cold only water feed
you will need to install a heater.
Cold feed in
Heater
Desired temperature out
Hot and
cold feed in
Themostatic
mixer
Desired temperature out

=
1
1
2
3
4
2
3 4
A(i)

100mm min
3.9inch min
85mm min
3.3inch min
Clear zone
380mm min
14.9inch min
A(ii)

E F
DCB
350mm min 13.7inch min
60mm
2.3inch
60mm
2.3inch
60mm
2.3inch
60mm
2.3inch
60mm
2.3inch
60mm
2.3inch
580mm min
22.8inch min
290mm min
11.4inch min
100mm min
3.9inch min
300mm min 11.8inch min
100mm min
3.9inch min
155mm max
6.1inch max

I
J K L
G H
6°
60mm
2.3inch
60mm
2.3inch
60mm
2.3inch
60mm
2.3inch

M
A
BF
E
D D
C C

2a 2b1
B
E
F
G
H
C D
3a 3b 3c 3d 3e
5mm
0.19inch
A
C
B
A

x2 x6
4a 4b 4c
MIN
100mm
3.9inch
5a 5b 5c 5d

6 7
8a 8b 8c 8d
x4
clik
clik
LN
clik
clik
clik
LN
clik
clik
clik
clik
LN
clik

clik
clik
LN
clik
12a
ON
LN
LN
clik
clik
LN
clik
910
11
x6x4

clik
clik
LN
clik
clik
clik
clik
clik
clik
clik
clik
clik
12b
x1
13a 13b
13c 13d 14

JN.92753 PN.251264-01-02 06.11.17 RCS PARIS 410 191 589
PT ([phone]
www.dyson.pt
QA ([phone]
www.dyson.ae
RO ([phone]
www.dyson.com.ro
RU ([phone]
www.dyson.com.ru
SA ([phone]
www.sa.dyson.com
SE ([phone]
www.dyson.se
SG ([phone]
www.dyson.com.sg
SK 00800 777 55 777
www.dyson.sk
SI ([phone]
www.dyson.si
TH ([phone]
www.dyson.co.th
TR ([phone]
www.dyson.com.tr
TW ([phone]
www.dyson.tw
UA (+ 38) 0 800 504-1800
www.dyson.com.ua
US ([phone]
www.dyson.com
UK ([phone]
www.dyson.co.uk
ROI ([phone]
www.dyson.ie
AE ([phone]
www.dyson.ae
AR ([phone]
www.dyson.com.ar
AT ([phone]
www.dyson.at
AU ([phone]
www.dyson.com.au
BE ([phone]
www.dyson.be
BG ([phone]
www.dyson.bg
BH ([phone]
www.dyson.ae
BR ([phone]
www.dyson.com.br
CA ([phone]
www.dysoncanada.ca
CH ([phone]
www.dyson.ch
CL ([phone]
www.dyson.cl
CN ([phone]
([phone]
www.dyson.cn
CO ([phone]
www.dyson.co
CR ([phone]
www.dyson.cr
Dyson Customer care
www.dyson.com
CY ([phone]
www.dyson.cy
CZ 00800 777 55 777
www.dyson.cz
DE ([phone]
www.dyson.de
DK ([phone]
www.dyson.dk
ES ([phone]
www.dyson.es
FI ([phone]
www.fi.dyson.com
FR ([phone]
www.dyson.fr
GR ([phone]
www.gr.dyson.com
GT ([phone]
www.dyson.gt
HK ([phone]
www.dyson.hk
HU 00800 777 55 777
www.dyson.hu
ID ([phone]
www.dyson.co.id
IL ([phone]
www.dyson.co.il
IN ([phone]
www.dyson.in
IT ([phone]
www.dyson.it
JM ([phone]
www.dyson.com
JP ([phone]
www.dyson.co.jp
KR ([phone]
www.kr.dyson.com
KW ([phone]
www.dyson.ae
LB ([phone]
www.lb.dyson.com
LU ([phone]
www.dyson.lu
MO ([phone]
([phone]
www.dyson.cn
MX ([phone]
www.dyson.mx
MY ([phone]
www.dyson.my
NL ([phone]
www.dyson.nl
NO ([phone]
www.dyson.no
NZ ([phone]
www.dyson.co.nz
OM ([phone]
www.dyson.ae
PA ([phone]
www.dyson.com.pa
PE ([phone]
www.dyson.com.pe
PH ([phone]
www.dyson.ph
PL ([phone]
www.dyson.pl

4
GB
ROI
IN
JM
MT
PH
SG
Important Safety Instructions
In the box
Pre-installation checks
GB/ROI/IN/JM/MT/PH/SG
Contents
Installation
Step-by-step
Test installation
Troubleshooting
5
6
7
9
11
11

5
GB
ROI
IN
JM
MT
PH
SG
READ AND SAVE THESE
INSTRUCTIONS
BEFORE INSTALLING OR USING THIS UNIT READ ALL
INSTRUCTIONS AND CAUTIONARY MARKINGS IN THIS
INSTALLATION GUIDE AND THE OWNER'S MANUAL.
WARNING
ALL INSTALLATION AND REPAIR WORK (PLUMBING AND
ELECTRICAL) SHOULD BE CARRIED OUT BY A QUALIFIED PERSON
OR DYSON SERVICE ENGINEER IN ACCORDANCE WITH CURRENT
LOCAL CODES OR REGULATIONS.
WARNING
RISK OF ELECTRIC SHOCK!
IF CASING IS REMOVED OR HANDLED IMPROPERLY THE INTERNAL
COMPONENTS OF THE UNIT MAY CAUSE HARM OR BECOME
PERMANENTLY DAMAGED.
THIS UNIT MUST BE EARTHED TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
Before beginning any installation work you must confirm the following.
•Check that the electrical supply corresponds to that shown on the
rating plate.
•A means for all-pole disconnection must be incorporated into fixed
wiring, in accordance with local wiring regulations.
•Connect the electricity supply using suitable conduit and electrical
fittings. Ensure that the conduit and wires are long enough to connect
to the backplate and the terminal block. Solid metal conduit is not
suitable for side entry.
WARNING
Use caution when unpacking the components. There may be sharp
edges/corners which may cut or cause harm.
DO NOT USE ANY JET WASH EQUIPMENT FOR CLEANING ON OR
NEAR THIS UNIT
IMPORTANT SAFETY
INSTRUCTIONS

6
GB
ROI
IN
JM
MT
PH
SG
In the box
Tools required:
Small Phillips screwdriver
7mm slotted screwdriver
2.5mm slotted screwdriver
Torx T15 screwdriver
Tape measure and pencil
Hand drill
Suitable drill bit
Pliers/wire strippers
Knife
Adjustable spanner
x2
x1