E-matic EHB150M User manual

High Lumen LED High Bays
150w, 230w, 300w
Models: EHB150M, EHB230M, EHB300M
Installation Manual

Introduction
Thank you for purchasing your E-Matic high lumen led high bay, these
instructions should be read carefully and retained for further reference
and maintenance.
IMPORTANT
•Installation must be carried out by a skilled electrician who is
familiar with the appropriate standards and technical
requirements of the appliance also taking in to consideration
the latest building regulations.
•The person carrying out the installation is to check and verify
that the total load on the circuit, including the rating of the
cable, fuse and or circuit breaker is not exceeded.
•Ensure there is adequate ventilation around the luminaire
•Ensure the AC mains supply is isolated when installing or
servicing.
•This product must be earthed.
•Once illuminated DO NOT look or stare at the LED fitting
directly when in close proximity.
•Never modify the luminaire, there are no user serviceable parts
inside.
•The luminaire has a selectable wattage output, please ensure
that the correct wattage output has been selected as this will
have an impact on the lighting design to ensure the correct
light levels are achieved.

Specification
•High lumen output LED high bay
•Slimline lightweight design
•Polycarbonate encapsulated lens module
•2835 LED chip
•Pre-wired cable – 1m
•90° beam angle
•4000k Colour temperature
•IP65 ingress protection
•IK09 impact protection
•50,000 hours rated life
•Input voltage – 100-277V AC 50 60Hz
•Power factor - PF≥0.9
•CRI rating - >70
•Operating temperature -20°～+40°c
•Selectable wattage
•5-year warranty
Model Lumens Wattage Dimensions
mm)
Input
Current
Weight
EHB150M 20520,
15120,
12660,
8310
150w,
100w,
80w,
50w
∅
320 x 199
1.8A 2.79Kg
EHB230M 32890,
27740,
21540,
14620
230w,
200w,
150w,
100w
∅
360 x 199
3.5A 4.08Kg
EHB300M 38670,
33880,
29120,
22760
300w,
230w,
200w,
150w
∅
4
0
0
x 205
3.5A 4.63Kg

Installation
•Ensure the electrical AC power is switched OFF before and
during installation
•For the AC supply cable and connections, a cable that is rated
to 90°C should be used
•Ensure the luminaire is securely fixed to a surface ceiling free
from vibration
•When adjusting the angle of the fitting please ensure that there
is enough slack in the cable so the range of movement of the
luminaire is unhindered
•A suitable IP rated junction box is required for the premade AC
electrical connections (Brown = Live, Blue = Neutral and
Yellow Green = Earth). This luminaire must be earthed
•Ensure that the correct wattage output has been selected as
this will have an impact on the lighting design to ensure the
correct light levels are achieved.
•Check the lighting fixture is firmly fixed and the Allen bolts have
been inserted in to the bracket
•Check all the connections are wired and terminated correctly

Refer to the following diagram when you install the fixture.
Fitted with Yoke bracket
Fitted with ring hook
1. Turn off the AC Supply
2. Fix the luminaire bracket to the surface or Ring hook.
3. Keep enough slack in cable to ensure when adjusting the angle,
the movement is unhindered when the yoke bracket is fitted.
4. Connections- AC-Live: Brown, AC-Neutral: Blue, GND Earth:
Yellow-Green.
5. Ensure that the correct wattage output has been selected as
this will have an impact on the lighting design to ensure the
correct light levels are achieved.
6. Check the circuit and connections are correct prior turning on
the AC supply

Adjust the wattage via dip switch please remove the screw on cap and replace)
Ensure that the correct wattage output has been selected (30w &
50w models only) as this will have an impact on the lighting design to
ensure the correct light levels are achieved.
EHB150M EHB230M EHB300M
Please Note: The cable must be connected either through a
waterproof connector or junction box. The waterproof connector or
junction box is not supplied and will need to purchase separately.

Maintenance
Repairs should only be carried out by a suitably qualified person.
Regular cleaning of luminaires should be carried out at regular
intervals not only to ensure good optical performance but also ensure
that dirt does not accumulate to such an extent as to impair the
electrical or thermal safety of the fitting. This should be done with the
luminaire switched off isolated and a soft damp cloth should be used,
do not use any chemicals or abrasives.
Light Source Maintenance
The light source of this luminaire is not replaceable; in case the light
source needs to be replaced (e.g. at the end of its life), the whole
luminaire shall be replaced.
Warranty
This product is covered by an extended warranty for 5 years from date
of purchase.
The extended warranty is available for installations in the UK or Ireland
by a competent person in accordance with the current building and IEE
wiring regulations.
If the defective product is no longer available, then Challenger may
provide alternatives of similar specification and quality.
The ambient temperatures and environment and voltage range
according to manufacturer specifications are not exceeded
The product is not exposed to any adverse mechanical stresses or
impact
For full terms and conditions in regard to our extended warranty
please refer to the website.

Follow us for all the latest news and product information
E-MATIC, Distributed by
CHALLENGER SECURITY PRODUCTS
10 Sandersons Way,
Blackpool, FY4 4NB
Email: [e-mail]
Web: www.challenger.co.uk
Due to our policy of continuous improvement we reserve the right to change specification
without prior notice. Errors and omissions excepted. These instructions have been carefully
checked prior to publication. However, no responsibility can be accepted by Challenger for any
misinterpretation of these instructions.
E-Matic_EHB150M_EHB230M_EHB300M_Instructions_Rev01