e-Turbine TB100 User manual

e-Turbine TB100 - User manual - Beez2B - Version 1.02 - February 2017
Page 1
Specications
Diagonal length between motors 100 mm
Length (Without prop) 83 mm
Width (Without prop) 83 mm
Prop diameter : 65 mm
Height : 56 mm
Motor set (ARF and BNF only) :
Motors : Brushed 8520
ESCs : 4 x Opto 12 A ESC
Battery : LiPo 1S 3,7 V 550 mAh 25C
Propellers : 2 blades 2.55""
Beez2B sprl
Rue des 3 Arbres, 16b
1180 Bruxelles Belgique
Tél.: [phone]
Fax : [phone]
•GAUI est distribué par :
Sauf erreurs et omissions, sous réserve de modications.
Attention cette traduction de cette notice est la propriété
de la société Beez2B. Toute reproduction même partielle est
interdite. Copyright © 2015 Beez2B
FPV racer
TB100
This manual is for :
•Frame Kit
•ARF Kit
•KBNF Kit
User Manual

e-Turbine TB100 - User manual - Beez2B - Version 1.02 - February 2017
Page 2
INTRODUCTION
Thank you for your purchase of the e-Turbine TB 100 FPV racer. We hope you will enjoy ying with it.
This model comes as a frame kit or as a ARF built kit with most of the electronics provided. For both kits,
assembly is made by the user.
This model comes also as a preassembled BNF kit with a DSM2 compatible receiver included and comes with
a carry case.
This mini FPV racer features a 100 mm diaginal size. The main frame is made of 3 mm thick durable plastic. For
the ARF and BNF kits, the 65 mm props are powered by 4 brushed 8.5 mm motors. The stability comes from
a Naze 32 ight controller. The 1S 3,7 V 550 mAh LiPo battery oers a ight time of 7 minutes. The 600 TVL
camera, the 5.8 GHz 25 mW 16 channels VTx are included.
For the ARF kit, you only need to add your transmitter, your receiver and a LiPo charger.
For the BNF kit, you need a DSM2 transmitter and a LiPo Charger.
FRAME KIT CONTENT
ARF KIT CONTENT

e-Turbine TB100 - User manual - Beez2B - Version 1.02 - February 2017
Page 3
BNF KIT CONTENT
LAYOUT

e-Turbine TB100 - User manual - Beez2B - Version 1.02 - February 2017
Page 4
MAIN COMPONENTS INSTALL
Close up on the 600 lines camera and
the 5.8 GHz video transmitter.

e-Turbine TB100 - User manual - Beez2B - Version 1.02 - February 2017
Page 5
NZ32 BRUSHED MOTOR FLIGHT CONTROLLER
The Flight controller use NAZE32 6DOF hardware, software compatibility with ALIENFLIGHTF1 or NAZE in CleanFlight congurator.
The FC use 3oZ 4 lays high quality PCB, support quadrocopter or hexrcopter, each brushed motor continuous working current up
to 6A, onboard 5V 400mA switching power BEC output for RX receiver or other equipment.
Hardware Base
NZ32 ight controller use MPU6050 and
STM32F103CB micro controller (128Kbytes ash
memory, 20Kbytes SRAM, ARM 72Mhz Cortex-M3)
Battery Input 1s lipo (4.35V maximum)
Onboard Brushed ESC Total 6 ways, support quadrocopter or hexrcopter, 6A
maximum each way
Onboard 5V BEC
Convert 1s battery input to 5V for RX receiver or
other equipment , current output 400mA maximum,
this 5V/400mA BEC can working reliable when input
voltage from 1.8V to 4.35V
Weigth : 4 g
Flash Firmware to NZ32 Brushed Motor FC
As show there is a button in NZ32 Brushed Motor FC, press this button then power on the
FC will trigger STM32 MCU into bootloader mode.
Actually this button connect to BOOT0 pin in STM32, press this button connect the
BOOT0 pin of STM32 to 3.3V. The rmware please select “ALIENFLIGHTF1” in CleanFlight
congurator as following.
User also can select “NAZE” rmware in CleanFlight congurator, but when use “NAZE”
rmware, user need change the register “motor_pwm_rate” from “400” to “32000” in CLI
page use command “set motor_pwm_rate = 32000”, then sent command “save” to save
the change of FC. If user don’t change this register when power on the brushed motor
will start running and can’t stop. We don’t recommend use “NAZE” rmware because it’s
too complex.
NZ32 Brushed Motor FC Receiver
Receiver Type OSD or BLUETOOTH Note
PPM √ (USART 1) -
S.BUS (USART 2) √ (USART 1) FC include inverter onboard, user only
need connect S.BUS signal to the socket.
DSM Satellite (USART 2) √ (USART 1)
When us DSM Satellite, FC can't trigger
satellite into binding mode, user need
bind the satellite before connect it to FC.

e-Turbine TB100 - User manual - Beez2B - Version 1.02 - February 2017
Page 6
Hardware Connection Diagram

e-Turbine TB100 - User manual - Beez2B - Version 1.02 - February 2017
Page 7
SP800 DSM2 COMPATIBLE RECEIVER WITH S-BUS AND PPM OUTPUT
Features:
• 1. Compatible with DSM2 transmitters or modules
• 2. Output S-BUS or CPPM
• 3. Designed for indoor FPV pocket drones from 80mm-110mm size such as inductrix
• 4.) Super light: only 0.8g
• Specication:
• Working voltage: 3.7V-5.5V
• Size: 17 mm * 13 mm * 5 mm
• Weight: 0.8 g
Binding to SBUS/PPM code: default mode is Sbus mode
1. SBUS mode: Turn o your transmitter , power on the receiver, about 6 seconds later, when the LED on the receiver ash rapidly ,
the receiver is ready for binding, then turn on the transmitter, then enter the binding mode, the led on the receiver will be light on ,
2. PPM mode: Turn o the transmitter, power up the receiver, wait for 30 seconds, turn on the transmitter, now the receiver is ready
for binding, after the receiver is bound to the transmitter, the led on the receiver will ash 1 time each 10 seconds.
LED instructions:
• High-speed LED ashing, means ready for binding
• LED out, means no signal.
• LED on, everything is ne and is in SBUS mode.
• LED on: About 10 seconds ash one time, means it is in PPM mode and works ne.
Beez2B wishes you nice igths with your e-Turbine TB-100 FPV Racer !

e-Turbine TB100 - User manual - Beez2B - Version 1.02 - February 2017
Page 8