"-=1:-,
)/3-66,:-9=1+-8<174-5;)/3-#7-+)5,"-;)131:73)@)9-,1=1:165:6.)/3-96<7C*@;0-)/3-96<7
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A. • www.eaglegrp.com
• Phone: 302/653-3000 • (Foodservice) 800/441-8440 • (MHC/Retail) 800/637-5100
• Fax: 302/653-2065
1) Cut holes as required in ounter top and front panel. See hart for ut out sizes.
See figure 1 for utout positioning.
2) Remove s rews holding ontrol panel to box and remove ontrol panel to expose field-
wiring terminals.
3) Apply a bead of NSF listed sili one adhesive to underside of top flange. Pass ontrol box
through top opening and work through utout in front panel. Seat unit to ounter top.
4) From underneath insert a long, flat head s rewdriver into the slots in the lo king angles.
Twist lo kwise 120˚ to lo k unit se urely to top.
5) Install ontrol box se urely in front panel utout with #8 sheet metal s rews in top and
bottom flanges.
6) Make ele tri al onne tions at terminal blo k as required. Conne t unit to dedi ated
ele tri al ir uit with properly sized ir uit breaker that meets the requirements of
NEC Arti le 422 and any lo al ele tri al odes. See unit model/serial for ele tri al
ratings. Repla e ontrol panel and atta h knobs.
Note: All units are shipped from the fa tory wired for single-phase operation; all but the
single-well units are field- onvertible for three-phase operation, see wiring diagram
for details.
7) A drain manifold with ball valve is provided on all units with drains. Lo ation of the valve
is left to the dis retion of the installer*. Install provided pipe plug on end opposite ball
valve. Use of a suitable pipe-sealing ompound is re ommended. When tightening
onne tions, ba k up manifold fittings with a wren h to prevent damage to the manifold.
5<51;:>1;0<;6133B');-9#@:;-4;0-*)33=)3=->133*-36+);-,65;0-3-.;-5,
#!$ $$#$('$&""""
"(
( %""#! # "$ ( %"%$"$%"!" !"(!
&*+$$+#'&%,*+%+$'$$+)#$&($,%#&!'*&*+$$+#'&
%,*+$$'.** ')*)-#&#+*"$$**#$ ')*)-##&!
)'%+"'++'%
!3-):-9-;)15
;01:4)5<)3.69
.<;<9-9-.-9-5+-
($%&+)+*#*+
3-4-5;'&
3-4-5;'&
3-4-5;'&
3-4-5;'&
1/0;5,1+);69
$0-946:;);1+65;963
65;96356*
!)9;:)9-;0-:)4-.69)3346,-35<4*-9:8<)5;1;1-:>133=)9@
part # description
($%&+)+*#*+2,+'#$$1+)0*+%
<;6133B65;9633-9&
<;6133B65;9633-9&
#63-561,&)3=-&
#63-561,&)3=-&
<;6133B#>1;+0
<;6133B"-:-9=619
SGDI Drop-Ins
(continued on Page 2)
model top control umbilical
number cutout cutout length
# F?F F?F F
# F?F F?F F
# F?F F?F F
# F?F F?F F
# F?F F?F F
# F?F F?F F
-56;-:41514<415:;)33);165:7)+15/.964
+<;6<;:;6=-9;1+)3+)*15-;>)33:7-9%31:;15/
figure 1
#$"%$ #$
