Easy wave RCJ02 User manual

GB Junction Box Receiver with Timer RCJ02
Display Overview
User Interface
AUTO
MANU
W
AM
PM
S
MO TU WE TH FR SA SU
Wochentage
(B1)Battery capacity (E)
Radio symbol
Move to intermediate position
(C2.2, C4.1)
Normal /daylight savings
time (D2)
Hour
format (B1)
Operating
Mode (C5)
Direction of motion
(C2.2, C4.1)
Current time
setting (B1)
Holiday
Mode (D3)
Twilight Mode
(C3)
Solar Protection
mode (C2)
Time/radio channel
/numerical value
Design
Operating the Receiver with Timer
The following settings have to be made to put
the receiver into operation and for later
modifications: Page
AMounting the Receiver ................2
BBasic Settings ........................2
B1 Setting the Time/Weekday ............2
B2 Measuring and Saving the Runtimes ....2
B3 Putting the Light Sensor into Operation ..2
COperating Shutters/Blinds ............3
C1 Factory Settings .................3
C2 Solar Protection Mode ...........3
C2.1 Setting the Brightness Value ..........3
C2.2 Setting the Intermediate Position .......3
C2.3 Activating Solar Protection Mode .......4
C3 Twilight Mode ...................4
C3.1 Setting the Twilight Value ............4
C3.2 Activating Twilight Mode ..............4
C4 Automatic Mode .................5
C4.1 Programming new Switching Times
and Intermediate Positions ...........5
C4.2 Deleting Switching Times ............5
C4.3 Changing Switching Times/
Intermediate Position ................5
C5 Changing the Operating Mode ...6
C6 Manual Mode ....................6
C6.1 Programming the Transmission Codes ..6
C6.2 Deleting Individual Transmission Codes .6
C6.3 Deleting all Transmission Codes .......6
DAdditional Functions .................7
D1 Activating the Holiday Function ........7
D2 Switching Between Normal Time
and Daylight Savings Time ...........7
D3 Vacation Mode
D4 Deletion of all Data (Reset)............7
EBattery Control Display .............7
FTroubleshooting ...................7
GGeneral Information ................7
RCJ02-5002E-01 2-channel 868,3 MHz
Scope of Delivery
Junction Box Receiver RCJ02 with Timer,
attachment frame, attachment set, operating
instructions
Technical Details
Frequency: 868,30 MHz
Modulation: FSK
Voltage supply: 230 V AC / 50 Hz
Connection value: 4 VA
Power consumption: 1,3 W
Output: 2 potential relay contacts
(normally open)
Max. contact load:
- resistive load cos =1: 4,0 A / 920 VA
- inductive load cos =0,8: 3,2 A / 736 VA
Protective class: IP 40
Operating temperature:for dry rooms only,
0°C to +50°C
Dimensions:
Please read this instruction manual
carefully before commissioning the
device!
Attention! Only a qualified electrician may
perform the electric installation!
Observe the valid laws, standards and
regulations as well as the manufacturer's
instructions regarding the devices to be
controlled!
Have malfunctioning devices checked by the
manufacturer!
Do not modify the device!
The relay contact is only designed for single-
phase supply!
Safety Advice
OK CLOCK
PROG ADJ
MODE
ESC
DEL
S/W
HOLI
UP
DOWN
STOP
The Junction Box Receiver RCJ02 (Easywave
radio control) may only be used to control
shutter or blind motors.
The manufacturer will not be liable for damage
caused by improper or inappropriate use.
Intended Use
The Junction Box Receiver with Timer allows to
control blinds or shutters depending on the time
and/or brightness. Brightness control is only
possible in connection with the Radio Light
Sensor SL01.
In addition, the receiver can also be operated
with hand transmitters and wall transmitters
included in the Easywave product range. The
transmitters must allow the functions UP (A),
STOP (C/D) and DOWN (B), 3-button
operation). The Easywave transmission code
must be memorized by the receiver before-
hand.
The following operating modes are available:
Time-Controlled:
Automatic Operation: Blinds are raised and
lowered either at the programmed switching
times or manually.
Automatic Operation with Partial Manual
Operation: The programmed switching times
as well as the Sun Protection/Twilight Mode
functions are deactivated until 24:00 hrs. After
24:00 hrs, the timer switches to Automatic
Mode.
Brightness-Controlled:
(only with Light Sensor SL01)
Solar Protection Mode: If a set brightness
value is exceeded, the blinds lower to a desired
shade position.
Twilight Mode: If a set brightness value is
undercut, the blinds are lowered completely.
Manual Mode: Raising and lowering of shutters
only via pushing the button on the timer or with
additional radio transmitters.
The timer offers the following additional
functions:
Holiday Mode: On holidays, you can activate
the switching times programmed for Sundays
with only one push of a button.
Switching from Normal to Daylight Savings
Time: You can switch the timer from normal to
daylight savings time with just one push of a
button.
Vacation Mode: Shutters are raised or lowered
with a time delay (at most 15 minutes) to the
programmed switching times in automatic
mode.
The following settings are available in
automatic mode and holiday mode:
-Day Function: Switching period 24 hours
or Week Function: Switching period one week
-Individual Switching Times: Different
switching times can be programmed for
each weekday or groups of weekdays.
-Intermediate Position: Lowering of
shutters to a desired shade position.
Functions
Power pack
unit
Timer
Attachment frame

2/8
A ReceiverMounting the
Turn the power supply off. Connect the
cable for the power supply and the
blind/shutter motor to the power unit as
shown in the connection diagram.
Insert the enclosed 4-pole pin strip into the
socket on the back of the Timer until it
snaps into place.
Insert the power pack into the casing and
screw it together with the attachment
frame. Insert the timer with the 4-pole pin
strip straight into the socket of the power
pack and snap it into the frame.
After switching on the supply
voltage, the timer is ready for
operation and you can start
programming.
After programming the basic settings (chapter
B), you can already control your shutters/blinds
manually or automatically with the preset
values (chapter C1).
If you want to use the additional operating
modes of the timer, please make the
corresponding settings.
If you additionally want to operate the receiver
with radio transmitters, register the
transmission codes in the shutter/blind control.
You can program up to 36 transmission codes.
N
N
230 V
L 4A
N
L
L
M
Press the OK button. The
weekday blinks on the
display.
Now select the respective day with the UP
and DOWN buttons.
Press the OK button
again. The settings are
saved and the timer
returns to operating
mode.
B1 Setting the Time/Weekday
B Basic Settings
If you do not press a button within 5 minutes
during programming, the timer automatically
returns to operating mode.
With ESC you can
cancel all
programming steps
at any time and
return to operating
mode.
In this case the settings are not
saved.
Setting Daylight Savings Time:
Setting/Changing the Time:
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press the S/W button. This way you switch
between daylight savings and normal time.
The display switches
between Wand S.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
DEL
S/W
W
MO TU•WE• •FR SA SOTH
S
Setting the Hour Format (12-/24 hours):
Press the MODE button
for more than 3 seconds.
The hour format switches
between AM and PM.
PM
MO TU•WE• •FR SA SOTH
AM
Setting the Weekday:
W
MO TU•WE• •FR SA SOTH
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
MO TU•WE• •FR SA SOTH
W
SA SO
MO Monday
TU Tuesday
WE Wednesday
TH Thursday
FR Friday
SA Saturday
SU Sunday
ESC
Press the CLOCK button
for more than 3 seconds.
The time on the display
starts to blink.
Set the time with the UP or DOWN button.
Advancing
the minutes
Resetting
the minutes
W
MO TU•WE• •FR SA SOTH
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CLOCK
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
MODE
PROG
W
MO TU•WE• •FR SA SOTH
MANU
W
MO TU WE TH FR SA SO
Set the timer to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode ADJ.
Press the OK button.
The display shows:
B2 Measuring/Saving the Runtimes
B3 Putting the Light Sensor
into Operation
For moving the shutter/blind into a desired
shade position, the timer has to measure and
save the runtime for raising and lowering the
shutters once.
Press ESC twice to
return to operating
mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ESC
W
MO TU•WE• •FR SA SOTH
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI Raise the shutter completely
with the UP button.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
OK
Keep the DOWN button
depressed until the
shutter is completely
closed.
The lowering time is
measured and saved.
Keep the UP button
depressed until the
shutter is completely
open.
The raising time is
measured and saved.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
To be able to use solar protection
and twilight mode, you have to
establish the radio connection
between the light sensor and the
timer.
For this, read the operating instruc-
tions for the Light Sensor SL01.
CR2032
+
C Operating Shutters/Blinds
You can also raise or lower the shutters in all
operating modes manually by pressing the
button on the timer or with a transmitter.
If the shutter raises or lowers
automatically, you can stop it by
briefly pressing the STOP button. C2.1 Setting the Brightness Value
The default switching times for automatic mode
are as follows:
- Shutter rises completely
Monday through Sunday at
7:00 hrs
- Shutter closes completely
Monday through Sunday at
21:00 hrs
Practical preset values are also programmed
for solar protection and twilight mode.
Press OK to save the value and then ESC
to return to operating mode.
Here you can define how far the shutters are to
lower for solar protection.
If an intermediate position is programmed, the
shutter first moves to the top end position and
then into the desired intermediate position.
When making your setting, make
sure that the shutter does not
obscure the sun sensor in the shade
position.
C2 Solar Protection Mode
Solar protection mode can only be activated when the shutter is completely raised either manually
with the timer or automatically. Do not interrupt the raising procedure with the STOP button.
The radio connection between the light sensor and the timer must also be established.
If you want to move your shutter to a certain shade position, please program the intermediate
position.
Here you can program the value for the
brightness at which your shutter is to move to
the desired shadow position.
We recommend initially using the factory
settings.
Press the UP button
again afterwards. The
display shows two
brightness values.
The left figure is the currently measured
value, the right one the default value or an
already programmed value. Press the UP button twice
afterwards. The display
shows the current value
for the intermediate
position as well as the
symbols for the direction and the
intermediate position.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI Press the OK button.
The right value starts to
blink on the display.
Select a new value with UP or
DOWN in a range between 0
and 29.
Program the brightness value for a time of
day at which the sun is so intense that you
want to lower the shutters or orient yourself
on the currently measured value.
If you want to update the measured value
once again beforehand, briefly press the
connection button on the light sensor.
OK
OK
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI
2x
Press the OK button. The
value starts to blink on the
display and symbols for the
direction.
Select a new value in 5% steps
with UP or DOWN.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
100%
25% 75%
0%
OK
2x
C1 Factory Settings
C2.2 Setting the Intermediate Position
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
Set the Timer to Operating Mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode.
Set the timer to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the Setup
Mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
ADJ
Press the UP button
briefly to change to
programming mode.
Press the UP button
briefly to change to
programming mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ESC
2.
1.
Press OK to save the value and then ESC
to return to operating mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
ESC
2.
1.
3/8
CR2032
+
Multi-pin connector

2/8
A ReceiverMounting the
Turn the power supply off. Connect the
cable for the power supply and the
blind/shutter motor to the power unit as
shown in the connection diagram.
Insert the enclosed 4-pole pin strip into the
socket on the back of the Timer until it
snaps into place.
Insert the power pack into the casing and
screw it together with the attachment
frame. Insert the timer with the 4-pole pin
strip straight into the socket of the power
pack and snap it into the frame.
After switching on the supply
voltage, the timer is ready for
operation and you can start
programming.
After programming the basic settings (chapter
B), you can already control your shutters/blinds
manually or automatically with the preset
values (chapter C1).
If you want to use the additional operating
modes of the timer, please make the
corresponding settings.
If you additionally want to operate the receiver
with radio transmitters, register the
transmission codes in the shutter/blind control.
You can program up to 36 transmission codes.
N
N
230 V
L 4A
N
L
L
M
Press the OK button. The
weekday blinks on the
display.
Now select the respective day with the UP
and DOWN buttons.
Press the OK button
again. The settings are
saved and the timer
returns to operating
mode.
B1 Setting the Time/Weekday
B Basic Settings
If you do not press a button within 5 minutes
during programming, the timer automatically
returns to operating mode.
With ESC you can
cancel all
programming steps
at any time and
return to operating
mode.
In this case the settings are not
saved.
Setting Daylight Savings Time:
Setting/Changing the Time:
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press the S/W button. This way you switch
between daylight savings and normal time.
The display switches
between Wand S.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
DEL
S/W
W
MO TU•WE• •FR SA SOTH
S
Setting the Hour Format (12-/24 hours):
Press the MODE button
for more than 3 seconds.
The hour format switches
between AM and PM.
PM
MO TU•WE• •FR SA SOTH
AM
Setting the Weekday:
W
MO TU•WE• •FR SA SOTH
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
MO TU•WE• •FR SA SOTH
W
SA SO
MO Monday
TU Tuesday
WE Wednesday
TH Thursday
FR Friday
SA Saturday
SU Sunday
ESC
Press the CLOCK button
for more than 3 seconds.
The time on the display
starts to blink.
Set the time with the UP or DOWN button.
Advancing
the minutes
Resetting
the minutes
W
MO TU•WE• •FR SA SOTH
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CLOCK
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
MODE
PROG
W
MO TU•WE• •FR SA SOTH
MANU
W
MO TU WE TH FR SA SO
Set the timer to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode ADJ.
Press the OK button.
The display shows:
B2 Measuring/Saving the Runtimes
B3 Putting the Light Sensor
into Operation
For moving the shutter/blind into a desired
shade position, the timer has to measure and
save the runtime for raising and lowering the
shutters once.
Press ESC twice to
return to operating
mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ESC
W
MO TU•WE• •FR SA SOTH
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI Raise the shutter completely
with the UP button.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
OK
Keep the DOWN button
depressed until the
shutter is completely
closed.
The lowering time is
measured and saved.
Keep the UP button
depressed until the
shutter is completely
open.
The raising time is
measured and saved.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
To be able to use solar protection
and twilight mode, you have to
establish the radio connection
between the light sensor and the
timer.
For this, read the operating instruc-
tions for the Light Sensor SL01.
CR2032
+
C Operating Shutters/Blinds
You can also raise or lower the shutters in all
operating modes manually by pressing the
button on the timer or with a transmitter.
If the shutter raises or lowers
automatically, you can stop it by
briefly pressing the STOP button. C2.1 Setting the Brightness Value
The default switching times for automatic mode
are as follows:
- Shutter rises completely
Monday through Sunday at
7:00 hrs
- Shutter closes completely
Monday through Sunday at
21:00 hrs
Practical preset values are also programmed
for solar protection and twilight mode.
Press OK to save the value and then ESC
to return to operating mode.
Here you can define how far the shutters are to
lower for solar protection.
If an intermediate position is programmed, the
shutter first moves to the top end position and
then into the desired intermediate position.
When making your setting, make
sure that the shutter does not
obscure the sun sensor in the shade
position.
C2 Solar Protection Mode
Solar protection mode can only be activated when the shutter is completely raised either manually
with the timer or automatically. Do not interrupt the raising procedure with the STOP button.
The radio connection between the light sensor and the timer must also be established.
If you want to move your shutter to a certain shade position, please program the intermediate
position.
Here you can program the value for the
brightness at which your shutter is to move to
the desired shadow position.
We recommend initially using the factory
settings.
Press the UP button
again afterwards. The
display shows two
brightness values.
The left figure is the currently measured
value, the right one the default value or an
already programmed value. Press the UP button twice
afterwards. The display
shows the current value
for the intermediate
position as well as the
symbols for the direction and the
intermediate position.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI Press the OK button.
The right value starts to
blink on the display.
Select a new value with UP or
DOWN in a range between 0
and 29.
Program the brightness value for a time of
day at which the sun is so intense that you
want to lower the shutters or orient yourself
on the currently measured value.
If you want to update the measured value
once again beforehand, briefly press the
connection button on the light sensor.
OK
OK
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI
2x
Press the OK button. The
value starts to blink on the
display and symbols for the
direction.
Select a new value in 5% steps
with UP or DOWN.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
100%
25% 75%
0%
OK
2x
C1 Factory Settings
C2.2 Setting the Intermediate Position
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
Set the Timer to Operating Mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode.
Set the timer to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the Setup
Mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
ADJ
Press the UP button
briefly to change to
programming mode.
Press the UP button
briefly to change to
programming mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ESC
2.
1.
Press OK to save the value and then ESC
to return to operating mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
ESC
2.
1.
3/8
CR2032
+
Multi-pin connector

Press OK again and the
weekdays blink on the
display.
Select the weekday or a
combination of weekdays with
UP or DOWN.
Press OK again and the
weekday blinks on the
display.
Select a new weekday with
UP or DOWN.
Set the timer to operating mode (ESC).
Press the PROG button
for more than 3 seconds.
The display shows the
free memory slots.
Select the switching time to be
deleted with UP or DOWN.
Press the DEL button for more than 3
seconds. The switching time is deleted and
the display shows the memory slots again.
Return to operating mode with ESC.
Press OK briefly. The
direction of the shutter
motion blinks on the
display.
With UP or DOWN, select for
which direction the changed
switching time is supposed to
apply.
Briefly press the OK
button. The saved
switching time is displayed.
Press ESC to return to operating
mode.
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
In order to be able to use the automatic
operation modes, you have to program the
switching times and - if required - the
intermediate positions for the shade position.
To do so, change to programming mode. If you
do not press a button in programming mode
within 5 minutes, the timer automatically returns
to operating mode.
The switching times programmed for automatic
mode take precedence over the settings for
solar protection or twilight mode. You can
program altogether 50 switching times.
If the timer is set to 12-hour display, the
switching times are also displayed in 12-hour
format.
PROG
MODE
C4.3 Changing Switching Times
Intermediate Positions
and
HOLI
S/W DEL
AUTO
C4.1 Programming Switching Times
and Intermediate Positions
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
PROG
MODE
AUTO
Set the timer to operating mode (ESC).
Press the PROG button
for more than 3 seconds.
The display shows the
free memory slots.
Select the switching time you
want to change with UP or
DOWN.
Briefly press the OK button.
The switching time starts to
blink on the display.
Set a new switching time
with UP or DOWN.
Set the timer to operating mode (ESC).
Press the PROG button for
more than 3 seconds to
change to programming
mode. The display shows
the free memory slots on
the right.
Briefly press the OK button.
The switching time starts to
blink on the display.
If the display shows FULL,
the memory for the
switching times is full.
Delete a time before
programming.
Set a new switching time with
UP or DOWN.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
PROG
MODE
AUTO
AUTO
MO TU WE TH FR SA SU
AUTO
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
AUTO
MO TU WE TH FR SA SU
MO Monday
TU Tuesday
WE Wednesday
TH Thursday
FR Friday
SA Saturday
SU Sunday
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
MO-FR Monday to Friday
SA-SU Saturday and Sunday
MO-SU daily (day function)
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI Press OK again. The
direction of the shutter
motion blinks on the
display.
With UP or DOWN, select for
which direction the changed
switching time is supposed to
apply.
LOWER
RAISE
OK
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
ESC
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI Press UP and DOWN at
the same time. The
intermediate position
blinks on the display.
Select a new value in 5% steps
with UP or DOWN. (Also see
chapter B.1.2)
The intermediate position is
programmed and indicated with the
two direction arrows.
Press UP and DOWN at
the same time. The
intermediate position
blinks on the display.
Select a new value in 5% steps
with UP or DOWN. (Also see
chapter B.1.2)
AUTO
MO TU WE TH FR SA SU
+
Twilight mode is now functioning. The shutter
lowers completely when the measured
brightness is less than the set value for approx.
6 minutes. However, beforehand the brightness
level must be higher than the set value for more
than one hour.
The shutter is not raised again automatically in
twilight mode. Open the shutter manually or use
a switching time programmed for automatic
mode.
The moon icon blinks if the radio
reception between the timer and the
light sensor is disrupted (see also
operating instruction of the Light
Sensor SL01).
Press the OK button. The
right value starts to blink
on the display.
Select a new value with UP or
DOWN in a range between 0
and 29.
Program the twilight value for a time of day
at which the brightness has the value at
which you want to lower the shutters or
orient yourself on the currently measured
value.
If you want to update the measured value
once again beforehand, briefly press the
connection button on the light sensor.
Briefly press the
SUN/MOON button;
the display shows the
moon icon.
If the timer is in operating mode, you can
activate twilight mode.
W
MO TU•WE• •FR SA SOTH
C3.2 Activating Twilight Mode
AUTO
MO TU WE TH FR SA SU
C4 Automatic Mode
C4.2 Deleting Switching Times
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI Briefly press the OK
button. The saved
switching time is
displayed.
Press ESC to return to operating
mode.
OK
ESC
C3.1 Setting the Twilight Value
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
ADJ
CR2032
+
Here you can program the value for the
brightness at which your shutter is to be closed.
We recommend initially using the factory
settings.
C3 Twilight Mode
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Briefly press the
SUN/MOON button;
the display shows
the sun icon.
If the timer is in operating mode, you can
activate the solar protection mode.
ADJ
W
AUTO
TH
Now the solar protection function is ready for
operation.
If the measured brightness value is approx. 12
minutes equal or larger than the set value, the
shutter lowers to the shade position.
If the measured value falls below half of the set
value for approx. 30 minutes, the shutter opens
completely again.
The sun icon blinks if the radio
reception between the Timer and the
light sensor is disrupted (see also
operating instruction of the Light
Sensor SL01).
C2.3 Activating Solar Protection Mode
Press the UP button three
times afterwards. The
display shows two
brightness values and the
moon icon.
The left figure is the currently measured
value, the right one the default value or an
already programmed value.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Set the timer to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
3x
Press OK to save the value and then ESC
to return to operating mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
ESC
2.
1.
4/8 5/8
Press the UP button
briefly to change to
Programming Mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
AUTO
MO TU WE TH FR SA SU
+
Intermediate position not yet programed:
OR
Intermediate position was already programmed:
The intermediate position blinks on
the display.
Enter a new value with UP or
DOWN.
AUTO
MO TU WE TH FR SA SU
AUTO
MO TU WE TH FR SA SU
AUTO
MO TU WE TH FR SA SU
AUTO
MO TU WE TH FR SA SU

Press OK again and the
weekdays blink on the
display.
Select the weekday or a
combination of weekdays with
UP or DOWN.
Press OK again and the
weekday blinks on the
display.
Select a new weekday with
UP or DOWN.
Set the timer to operating mode (ESC).
Press the PROG button
for more than 3 seconds.
The display shows the
free memory slots.
Select the switching time to be
deleted with UP or DOWN.
Press the DEL button for more than 3
seconds. The switching time is deleted and
the display shows the memory slots again.
Return to operating mode with ESC.
Press OK briefly. The
direction of the shutter
motion blinks on the
display.
With UP or DOWN, select for
which direction the changed
switching time is supposed to
apply.
Briefly press the OK
button. The saved
switching time is displayed.
Press ESC to return to operating
mode.
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
In order to be able to use the automatic
operation modes, you have to program the
switching times and - if required - the
intermediate positions for the shade position.
To do so, change to programming mode. If you
do not press a button in programming mode
within 5 minutes, the timer automatically returns
to operating mode.
The switching times programmed for automatic
mode take precedence over the settings for
solar protection or twilight mode. You can
program altogether 50 switching times.
If the timer is set to 12-hour display, the
switching times are also displayed in 12-hour
format.
PROG
MODE
C4.3 Changing Switching Times
Intermediate Positions
and
HOLI
S/W DEL
AUTO
C4.1 Programming Switching Times
and Intermediate Positions
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
PROG
MODE
AUTO
Set the timer to operating mode (ESC).
Press the PROG button
for more than 3 seconds.
The display shows the
free memory slots.
Select the switching time you
want to change with UP or
DOWN.
Briefly press the OK button.
The switching time starts to
blink on the display.
Set a new switching time
with UP or DOWN.
Set the timer to operating mode (ESC).
Press the PROG button for
more than 3 seconds to
change to programming
mode. The display shows
the free memory slots on
the right.
Briefly press the OK button.
The switching time starts to
blink on the display.
If the display shows FULL,
the memory for the
switching times is full.
Delete a time before
programming.
Set a new switching time with
UP or DOWN.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
PROG
MODE
AUTO
AUTO
MO TU WE TH FR SA SU
AUTO
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
AUTO
MO TU WE TH FR SA SU
MO Monday
TU Tuesday
WE Wednesday
TH Thursday
FR Friday
SA Saturday
SU Sunday
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
MO-FR Monday to Friday
SA-SU Saturday and Sunday
MO-SU daily (day function)
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI Press OK again. The
direction of the shutter
motion blinks on the
display.
With UP or DOWN, select for
which direction the changed
switching time is supposed to
apply.
LOWER
RAISE
OK
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
ESC
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI Press UP and DOWN at
the same time. The
intermediate position
blinks on the display.
Select a new value in 5% steps
with UP or DOWN. (Also see
chapter B.1.2)
The intermediate position is
programmed and indicated with the
two direction arrows.
Press UP and DOWN at
the same time. The
intermediate position
blinks on the display.
Select a new value in 5% steps
with UP or DOWN. (Also see
chapter B.1.2)
AUTO
MO TU WE TH FR SA SU
+
Twilight mode is now functioning. The shutter
lowers completely when the measured
brightness is less than the set value for approx.
6 minutes. However, beforehand the brightness
level must be higher than the set value for more
than one hour.
The shutter is not raised again automatically in
twilight mode. Open the shutter manually or use
a switching time programmed for automatic
mode.
The moon icon blinks if the radio
reception between the timer and the
light sensor is disrupted (see also
operating instruction of the Light
Sensor SL01).
Press the OK button. The
right value starts to blink
on the display.
Select a new value with UP or
DOWN in a range between 0
and 29.
Program the twilight value for a time of day
at which the brightness has the value at
which you want to lower the shutters or
orient yourself on the currently measured
value.
If you want to update the measured value
once again beforehand, briefly press the
connection button on the light sensor.
Briefly press the
SUN/MOON button;
the display shows the
moon icon.
If the timer is in operating mode, you can
activate twilight mode.
W
MO TU•WE• •FR SA SOTH
C3.2 Activating Twilight Mode
AUTO
MO TU WE TH FR SA SU
C4 Automatic Mode
C4.2 Deleting Switching Times
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI Briefly press the OK
button. The saved
switching time is
displayed.
Press ESC to return to operating
mode.
OK
ESC
C3.1 Setting the Twilight Value
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
ADJ
CR2032
+
Here you can program the value for the
brightness at which your shutter is to be closed.
We recommend initially using the factory
settings.
C3 Twilight Mode
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Briefly press the
SUN/MOON button;
the display shows
the sun icon.
If the timer is in operating mode, you can
activate the solar protection mode.
ADJ
W
AUTO
TH
Now the solar protection function is ready for
operation.
If the measured brightness value is approx. 12
minutes equal or larger than the set value, the
shutter lowers to the shade position.
If the measured value falls below half of the set
value for approx. 30 minutes, the shutter opens
completely again.
The sun icon blinks if the radio
reception between the Timer and the
light sensor is disrupted (see also
operating instruction of the Light
Sensor SL01).
C2.3 Activating Solar Protection Mode
Press the UP button three
times afterwards. The
display shows two
brightness values and the
moon icon.
The left figure is the currently measured
value, the right one the default value or an
already programmed value.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Set the timer to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
3x
Press OK to save the value and then ESC
to return to operating mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
ESC
2.
1.
4/8 5/8
Press the UP button
briefly to change to
Programming Mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
AUTO
MO TU WE TH FR SA SU
+
Intermediate position not yet programed:
OR
Intermediate position was already programmed:
The intermediate position blinks on
the display.
Enter a new value with UP or
DOWN.
AUTO
MO TU WE TH FR SA SU
AUTO
MO TU WE TH FR SA SU
AUTO
MO TU WE TH FR SA SU
AUTO
MO TU WE TH FR SA SU

C6.3 Deleting all Transmission Codes
Set the timer to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
Briefly press OK and then
immediately DOWN. dE
ALL blinks on the display.
Press the DEL button for
more than 3 seconds. All
codes are deleted. The
display briefly shows the
empty memory slots and
then returns to blinking dE
ALL.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
S/W
DEL
2.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press ESC once to save and return
toprogramming mode or twice to return to
operating mode immediately.
ESC
2x
AUTO
C6.1Programming the Transmission Codes
C6.2 Deleting Individual Transmission Codes
Set the timer to operating mode (ESC).
Press the UP, DOWN or STOP button; the
shutter moves in the desired direction or
stops.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
C6 Manual Operation
In manual operation with timer, you can also
raise or lower the shutters with a push of a
button.
DOWN
(lower)
STOP
UP
(Raise)
C5 Changing the Operating Mode
Automatic Mode
Set the timer to operating mode (ESC).
By briefly pressing the MODE button, select
the operating mode AUTO (automatic
mode) or AUTOMANU (automatic mode
with partial manual operation).
MANU
W
MO TU WE FR SA SOTH
AUTO
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
PROG
MODE
W
MO TU WE FR SA SOTH
AUTO
Solar Protection/Twilight Mode
Set the timer to operating mode (ESC).
By briefly pressing the SUN/MOON button,
activate/deactivate solar protection, twilight
or both modes.
W
AUTO
MO TU WE FR SA SOTH
W
AUTO
MO TU WE FR SA SOTH
W
AUTO
TH
W
AUTO
TH
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
If you additionally want to operate your shutter
control with radio transmitters, you have to
memorize the Easywave transmission code in
the receiver.
Operation of the shutter control is only possible
with Easywave 3-button transmitters. The
buttons have the following function:
×UP (transmitter button A),
×STOP (transmitter button C or D) and
×DOWN (transmitter button B).
To transmit the transmission code, you
generally only have to press button A; the
function of the individual buttons is then defined
automatically by the control.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
Set the timer to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode.
Set the timer to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the sSetup
mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
ADJ
2.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press ESC twice to save the codes and
return to operating mode.
ESC
Briefly press the OK
button. Ln blinks on the
display and the number of
free memory slots is
displayed.
Now repeatedly press the button UP (A) on
the transmitter for the key combination
whose code you want to transmit.
The number of free
memory slots decreases
on the display and the
antenna icon is displayed
briefly.
You can enter at most 36
transmitters in sequence.
Once all memory slots are
occupied, the display
shows FULL.
Briefly press OK and then
immediately UP. dE
blinks on the display and
the number of free
memory slots is
displayed.
Now repeatedly press the button UP (A) on
the transmitter for the key combination
whose code you want to delete.
The number of free
memory slots increases
on the display and the
antenna icon is displayed
briefly.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
2x
2.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press ESC once to save and return to
programming mode or twice to return to
operating mode immediately.
ESC
2x
6/8
Press the UP button
briefly to change to
programming mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press the UP button
briefly.
Now you change to
programming mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press the UP button
briefly to change to
programming mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Set the Timer to Operating Mode (ESC).
Press MODE until the
dice appears on the
display.
In Vacation Modethe Holiday Function
is deactivated with a random offset of
±15 minutes.
Set the Timer to Operating Mode (ESC).
Turn the holiday
function ON or OFF by
pressing the HOLI
button.
The weekday SU
blinks on the display.
If you have activated the Holiday
Function prior to 18:00 hrs, it is
automatically deactivated at 24:00 hrs
on the same day.
If you have activated the Holiday
Function after 18:00 hrs, it is first
automatically deactivated at 24:00 hrs
on the next day.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
D1 Activating the Holiday Function
DAdditional Functions
D4 Deletion of all data (reset) (Reset)
D2 Activating Daylight Savings Time
W
MO TU WE FR SATH SU
AUTO
HOLI
CLOCK
S
AUTO
MO TU WE FR SA SOTH
Set the Timer to Operating Mode (ESC).
Briefly press the S/W
button. The display
changes from W to S
and the clock is moved
forwards/backwards
one hour.
S/W
DEL
D3 Activating Vacation Mode
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
PROG
MODE
S
AUTO
MO TU WE FR SA SOTH
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press the ESC and the DEL button at
the same time for more than 3
seconds.
All saved data is
deleted and the
factory settings are
restored.
After the reset, the transmission codes
of the radio transmitters have to be
registered again in the control.
PROG ADJ
MODE
ESC
S/W DEL
HOLI
ESC
S/W
DEL
EBattery Control Display
If the battery icon blinks on the Timer's display,
the battery of the Light Sensor SL01 is weak.
Change the battery of the Light Sensor SL01
according to the operating instructions.
FTroubleshooting
- Blinking symbol: Change the battery of the
Light Sensor.
-If the receiver does not react to the push of a
button on a radio transmitter in Manual Mode:
Re-enter the transmitter code into the receiver
(chapter C6).
-If the receiver does not react to the
programmed switching commands in
Automatic Mode: Check whether the Timer is
in "Automatic Mode" (see chapter C5). Check
the programmed switching times (chapter
C4.1).
-Solar Protection/Twilight Mode cannot be
activated: Re-establish the connection
between the Light Sensor and the Timer. (See
the operating instructions for the Light
Sensor).
-The receiver does not move the shutter into
the intermediate position: set the runtime
again (chapter B2).
-After changing the sensor battery, the Light
Sensor reception is disrupted and the
SUN/MOON icon blinks: Wait approx. 35
minutes until reception is restored
automatically.
Disposal
Conformity
Dispose of used batteries in a
recycling bin for batteries or via the
specialist trade.
Put the packaging material into the
recycling bins for cardboard, paper
and plastics.
Dispose of the waste product via a
collection point for electronic scrap or
via your specialist dealer.
Waste electrical products should not be
disposed of with household waste!
The product fulfils the essential
requirements of the R&TTE directive
1999/5/EG.
For use in: EU/CH/FL/IS/N
Warranty
We will remedy defects on the device based on
material or production errors within the statutory
warranty period or exchange the device.
In case of unauthorised tampering with the
device, the warranty is void.
The Declaration of Conformity can be found on
the Internet at: www.eldat.de.
GGeneral Information
MANU
W
MO TU WE TH FR SA SO
7/8
On holidays, you can activate the switching
times programmed for Sundays with only one
push of a button.
Shutters are raised or lowered with a time delay
(at most 15 minutes) to the programmed
switching times in automatic mode.

C6.3 Deleting all Transmission Codes
Set the timer to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
Briefly press OK and then
immediately DOWN. dE
ALL blinks on the display.
Press the DEL button for
more than 3 seconds. All
codes are deleted. The
display briefly shows the
empty memory slots and
then returns to blinking dE
ALL.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
S/W
DEL
2.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press ESC once to save and return
toprogramming mode or twice to return to
operating mode immediately.
ESC
2x
AUTO
C6.1Programming the Transmission Codes
C6.2 Deleting Individual Transmission Codes
Set the timer to operating mode (ESC).
Press the UP, DOWN or STOP button; the
shutter moves in the desired direction or
stops.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
C6 Manual Operation
In manual operation with timer, you can also
raise or lower the shutters with a push of a
button.
DOWN
(lower)
STOP
UP
(Raise)
C5 Changing the Operating Mode
Automatic Mode
Set the timer to operating mode (ESC).
By briefly pressing the MODE button, select
the operating mode AUTO (automatic
mode) or AUTOMANU (automatic mode
with partial manual operation).
MANU
W
MO TU WE FR SA SOTH
AUTO
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
PROG
MODE
W
MO TU WE FR SA SOTH
AUTO
Solar Protection/Twilight Mode
Set the timer to operating mode (ESC).
By briefly pressing the SUN/MOON button,
activate/deactivate solar protection, twilight
or both modes.
W
AUTO
MO TU WE FR SA SOTH
W
AUTO
MO TU WE FR SA SOTH
W
AUTO
TH
W
AUTO
TH
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
If you additionally want to operate your shutter
control with radio transmitters, you have to
memorize the Easywave transmission code in
the receiver.
Operation of the shutter control is only possible
with Easywave 3-button transmitters. The
buttons have the following function:
×UP (transmitter button A),
×STOP (transmitter button C or D) and
×DOWN (transmitter button B).
To transmit the transmission code, you
generally only have to press button A; the
function of the individual buttons is then defined
automatically by the control.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
Set the timer to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode.
Set the timer to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the sSetup
mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
ADJ
2.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press ESC twice to save the codes and
return to operating mode.
ESC
Briefly press the OK
button. Ln blinks on the
display and the number of
free memory slots is
displayed.
Now repeatedly press the button UP (A) on
the transmitter for the key combination
whose code you want to transmit.
The number of free
memory slots decreases
on the display and the
antenna icon is displayed
briefly.
You can enter at most 36
transmitters in sequence.
Once all memory slots are
occupied, the display
shows FULL.
Briefly press OK and then
immediately UP. dE
blinks on the display and
the number of free
memory slots is
displayed.
Now repeatedly press the button UP (A) on
the transmitter for the key combination
whose code you want to delete.
The number of free
memory slots increases
on the display and the
antenna icon is displayed
briefly.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
2x
2.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press ESC once to save and return to
programming mode or twice to return to
operating mode immediately.
ESC
2x
6/8
Press the UP button
briefly to change to
programming mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press the UP button
briefly.
Now you change to
programming mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press the UP button
briefly to change to
programming mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Set the Timer to Operating Mode (ESC).
Press MODE until the
dice appears on the
display.
In Vacation Modethe Holiday Function
is deactivated with a random offset of
±15 minutes.
Set the Timer to Operating Mode (ESC).
Turn the holiday
function ON or OFF by
pressing the HOLI
button.
The weekday SU
blinks on the display.
If you have activated the Holiday
Function prior to 18:00 hrs, it is
automatically deactivated at 24:00 hrs
on the same day.
If you have activated the Holiday
Function after 18:00 hrs, it is first
automatically deactivated at 24:00 hrs
on the next day.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
D1 Activating the Holiday Function
DAdditional Functions
D4 Deletion of all data (reset) (Reset)
D2 Activating Daylight Savings Time
W
MO TU WE FR SATH SU
AUTO
HOLI
CLOCK
S
AUTO
MO TU WE FR SA SOTH
Set the Timer to Operating Mode (ESC).
Briefly press the S/W
button. The display
changes from W to S
and the clock is moved
forwards/backwards
one hour.
S/W
DEL
D3 Activating Vacation Mode
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
PROG
MODE
S
AUTO
MO TU WE FR SA SOTH
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press the ESC and the DEL button at
the same time for more than 3
seconds.
All saved data is
deleted and the
factory settings are
restored.
After the reset, the transmission codes
of the radio transmitters have to be
registered again in the control.
PROG ADJ
MODE
ESC
S/W DEL
HOLI
ESC
S/W
DEL
EBattery Control Display
If the battery icon blinks on the Timer's display,
the battery of the Light Sensor SL01 is weak.
Change the battery of the Light Sensor SL01
according to the operating instructions.
FTroubleshooting
- Blinking symbol: Change the battery of the
Light Sensor.
-If the receiver does not react to the push of a
button on a radio transmitter in Manual Mode:
Re-enter the transmitter code into the receiver
(chapter C6).
-If the receiver does not react to the
programmed switching commands in
Automatic Mode: Check whether the Timer is
in "Automatic Mode" (see chapter C5). Check
the programmed switching times (chapter
C4.1).
-Solar Protection/Twilight Mode cannot be
activated: Re-establish the connection
between the Light Sensor and the Timer. (See
the operating instructions for the Light
Sensor).
-The receiver does not move the shutter into
the intermediate position: set the runtime
again (chapter B2).
-After changing the sensor battery, the Light
Sensor reception is disrupted and the
SUN/MOON icon blinks: Wait approx. 35
minutes until reception is restored
automatically.
Disposal
Conformity
Dispose of used batteries in a
recycling bin for batteries or via the
specialist trade.
Put the packaging material into the
recycling bins for cardboard, paper
and plastics.
Dispose of the waste product via a
collection point for electronic scrap or
via your specialist dealer.
Waste electrical products should not be
disposed of with household waste!
The product fulfils the essential
requirements of the R&TTE directive
1999/5/EG.
For use in: EU/CH/FL/IS/N
Warranty
We will remedy defects on the device based on
material or production errors within the statutory
warranty period or exchange the device.
In case of unauthorised tampering with the
device, the warranty is void.
The Declaration of Conformity can be found on
the Internet at: www.eldat.de.
GGeneral Information
MANU
W
MO TU WE TH FR SA SO
7/8
On holidays, you can activate the switching
times programmed for Sundays with only one
push of a button.
Shutters are raised or lowered with a time delay
(at most 15 minutes) to the programmed
switching times in automatic mode.

80527 0108 GB
Customer Service
If the device does not work properly despite
proper handling or in case of damage, please
contact your retailer or the following address:
ELDAT GmbH
Im Gewerbepark 14
15711 Zeesen
Germany
Phone: + 49 (0) 33 75 / 90 37-0
Fax: + 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
E-mail: [email protected]