The alarm sound can be turned off with the
buttons 1 or 0 or with the acknowledgement
transmitter.
Attention! After an alarm message, the alarm
indicator is deactivated for 5 minutes. The LEDs
blink alternately. Further alarms will not be
signalledduringthistime.
In order to cancel this status, turn the alarm
functionOFFonceandthenONagain.
> 1,6 s
within
20 s
within
20 s
within 20 s
This function serves to transmit the Easywave
send code A1 (ON) to an Easywave wireless
receiver. This way, e.g. a light source or another
electrical appliance can be activated in case of
analarm.
Transmit the send code of the RTRP02 to the
receiver:
1. Press button 0 and button 1 simultaneously
untilbothLEDsblink.Ifyou want tocancelthe
teach-inprocedure,brieflypressbutton0.
2. Ready the wireless receiver for the teach-in
process. Within 20 seconds, press the button
1onthealarmindicatoruntilLED1blinks.
3. Press the button 1 again within 20 seconds;
LED1is lit.The send codeAistransmittedfor
3 seconds. Afterwards, the alarm indicator
changesitsstatusto"readyforoperation".
If there is no input within 20 seconds, the
alarm indicator switches automatically to
„readyforoperation".
Attention! After a RESET, send code A can no
longer be sent automatically in case of an alarm.
Repeat the steps 1 to 3 in order to reactivate the
function. The wireless receiver does not have to
besettoteach-inmodeforthispurpose.
This function serves to transmit the Easywave
send code B2 (DOWN) to an Easywave wireless
receiver.Thisway,e.g.ashuttercanbeclosedor
another electrical appliance can be activated in
caseofanalarm.
Transmit the send code to the receiver as
describedinthefollowing:
1. Press button 0 and button 1 simultaneously
untilbothLEDsblink.Ifyou want tocancelthe
teach-inprocess,brieflypressthebutton0.
2. Ready the wireless receiver for the teach-in
process. Within 20 seconds, press the button
0onthealarmindicatoruntilLED0blinks.
3. Press the button 0 again within 20 seconds;
LED0islit.ThesendcodeBistransmittedfor
3 seconds. Afterwards, the alarm indicator
changesitsstatusto"readyforoperation".
If there is no input within 20 seconds, the
alarm indicator switches automatically to
„readyforoperation".
Attention! After a RESET, send code A can no
longer be sent automatically in case of an alarm.
Repeat the steps 1 to 3 in order to reactivate the
function. The wireless receiver does not have to
besettoteach-inmodeforthispurpose.
Switch on lighting Close a shutter
3 s 3 s
> 1,6 s > 1,6 s
> 1,6 s
1
L 10A
1
L 10A
Transmission code A
is transferred Transmission code B
is transferred
within
20 s
or
or
> 1,6 s
> 1,6 s
within
20 s
within
20 s
This function serves to transmit the coding of a
wirelesstransmittertothealarmindicator.
1. Press button 0 and button 1 simultaneously
untilboth LEDs blink.If youwant to cancelthe
teach-inprocess,brieflypressthebutton0.
2. Pressbutton1;nowLED1blinks.
3. 1.Press the button of the wireless transmitter
which you want to use to acknowledge the
alarm signal within 20 seconds until LED 1 of
the alarm indicator lights up. After approx. 3
seconds, the alarm indicator switches to
"readyforoperation".
If there is no input within 20 seconds, the
alarm indicator switches automatically to
"readyforoperation".
You can save at most four send codes. If you
teach in more transmitters, the oldest code is
overwritten.
Incaseawindowhandlecontactthatwasalready
taught in issues an alarm, the teach-in process
cannotbeactivated.
Memorizing the code of an
acknowledgement transmitter
Acknowledge the alarm
Switch off the alarm function
Switch on the alarm function
An alarm message can only be received if the
alarm function is activated and if the coding of a
windowhandle contact wastaught intothe alarm
indicator.
After a power failure, the alarm function is
activatedautomatically.
Aktivate/deactivate the
alarm function
Button 0
Alarm
OFF
OFF
Button 1
Alarm
ON
ON
> 1,6 s
> 1,6 s
This function serves to transfer the coding of the
windowhandlecontactstothealarmindicator.
1. Press button 1 and button 0 simultaneously
untilboth LEDs blink.If youwant to cancelthe
teach-inprocess,brieflypressthebutton0.
2. Press the button on the window handle
contact within 20 seconds. If there is no input
within 20 seconds, the alarm indicator
switches automatically to "ready for
operation".
If the coding was transferred, LED 1 blinks for
approx. 3 seconds. Afterwards, the alarm
indicator changes its status to "ready for
operation".
Repeat this procedure with every window handle
contact.
Incaseawindowhandlecontactthatwasalready
taught in issues an alarm, the teach-in process
cannotbeactivated.
Memorizing the code of a window
handle contact RTS26
> 1,6 s
3 s
3 s
Window handle contact RTS26
Keep button 1 depressed until the two status
LEDsturnred.
Keep button 0 depressed until the two red status
LEDsgooff.
Start-up the Alarm annunciator
1. Plug the alarm annunciator
intoanywalloutlet,youcan
hear an acknowledgement
signal.
2. Teach the codes of the window handle
contactsintothealarmindicator(seechapter
"Teaching in the window handle contact
RTS26").
3. Activate the alarm function (see chapter
"Activating/deactivatingthealarmfunction").
Caution: Makesurethatthereisno interference
with the wireless connection. Do not mount the
device in a distribution box, metal casings or in
directproximitytolargemetalobjects.
If the window handle contact detects a
movement of the window handle, a radio
message is sent to the alarm indicator and an
alarm sound is emitted for approx. 3 minutes.
Thisalarmsignalcanbeturnedoffdirectlyonthe
alarm indicator or with an additional wireless
transmitter.
The outlet cannot be switched wireless and may
instead be used as a connection for electrical
devices(230VAC,50Hz,upto16A).
