Eaton PXGMS Power Xpert Gateway Minislot UPS Programming manual

Eaton®Power Xpert®Gateway Minislot (PXGMS) UPS Card
Quick Start Instructions
Package Contents
lPower Xpert Gateway Minislot (PXGMS) UPS Card
lUSB Cable
lQuick Start Instructions
Ident
Power
Act
100
PXGMS UPS
Restart TX RX
Setup
CMN
Status
DHCP EMP
Ethernet 10/100
+
-

Help Desk Numbers
United States 1-800-356-5737 or 1-800-843-9433
Canada 1-800-461-9166 ext 260
All Other Countries Call your local service representative
Web Site www.eaton.com/pxgms
NOTE: On the Web site opening page, click Support and select the
Customer Service link for more information.
Eaton, Power Xpert, and PredictPulse are registered trademarks of Eaton
Corporation or its subsidiaries and affiliates. Google Chrome is a trademark of
Google Inc. Linux is a registered trademark of Linus Torvalds. Microsoft, Internet
Explorer, and Windows are registered trademarks of Microsoft Corporation in the
United States and in other countries. Mozilla and Firefox are registered
trademarks of the Mozilla Foundation. All other trademarks are property of their
respective companies.
©Copyright 2015 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No
part of this document may be reproduced in any way without the express written
approval of Eaton Corporation.

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2 1
TABLE OF CONTENTS
Section 1 Installation Checklist ........................................................................ 2
Section 2 Install the Card ................................................................................. 3
Section 3 Connect the Card to the Computer .................................................. 5
Section 4 Install the USB Driver Software ...................................................... 7
Section 5 Obtain a DHCP-Assigned IP Address ............................................. 11
Section 6 Assign an IP Address Manually ..................................................... 15
Section 7 Disable Browser Compatibility Mode ............................................ 18
Section 8 Register a PredictPulse Subscription ............................................. 20

2 Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2
Section 1 Installation Checklist
1. Verify that the following items are available:
oPower Xpert Gateway Minislot (PXGMS) UPS Card package contents
(card, cable, Quick Start Instructions)
oPhillips®screwdriver
oAvailable USB port on a computer running Microsoft®Windows®
oWeb browser (Microsoft Internet Explorer® version 8.0 and higher,
Mozilla®Firefox®, or Google Chrome™ are recommended)
2. If you are going to use Dynamic Host Configuration Protocol (DHCP), provide
your local network administrator with the card's MAC address. The MAC
address is located on either the shipping box label or the label on this card.
oMAC Address _____________________________________________
3. If you are not going to use DHCP to provide any of the settings listed below,
contact your local network administrator for the settings.
In the table below, check the DHCP check box or enter the values for manual
configuration.You will reference this data later in the procedure.
4. If you need e-mail functionality, obtain the SMTP mail server's IP address or
host name. If using the SMTP host name, verify that you also have the
Name Server IP address (see Step 3).
oSMTP (mail server) IP Address
or Host Name _____________________________________________
Item DHCP* Manual Configuration
IPv4 oCard IP Address: ________________________
Netmask: ________________________
Gateway: ________________________
DNS – Name Servers oName Server #1: ________________________
Name Server #2: ________________________
Name Server #3: ________________________
DNS – Domain oDomain: ________________________
* The network administrator normally sets up the DHCP server to provide a static IP address each time
the card makes a DHCP request.

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2 3
Section 2 Install the Card
Note: The hot-swappable PXGMS card can be installed without turning off the
UPS or disconnecting the load.
Note: If your UPS is a 93PM, there may be a metal strip that prevents you
from installing the PXGMS card. If so, locate the metal strip bolted to
the top of the UPS. Remove the three bolts that attach the metal strip.
Then, follow the procedure to install the PXGMS card.
To install the PXGMS card:
1. On the PXGMS card, verify that all six DIP switches are in the OFF position
(see Figure 1).
Figure 1. Verify DIP Switches are OFF
2. If not already done, record the MAC address from either the shipping box
label or the label on this card for future reference (see the "Installation
Checklist" on page 2).
3. Remove the minislot cover from the UPS. Retain the screws.
Note: If another card is already installed with an attached communication
cable, disconnect the cable and then remove the card.
4. To prevent electrostatic discharge (ESD), place one hand on a metal surface,
such as the UPS rear panel.
Ident
Power
Act
100
PXGMS UPS
Restart
TX
RX
Setup
CMN
Status
DHCP
EMP
Ethernet 10/100
+
-
2
13456
ON
OFF

4 Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2
5. Slide the card into the open slot and secure it with the screws removed in
Step 2 (see Figure 2).
Figure 2. Secure the PXGMS Card
6. From your laptop, go to www.eaton.com/pxgms.
7. On the Features tab, click the Download Configuration File link to
download the configuration file.
8. Save the driver configuration file (powerxpert.inf) to the C: drive using the
default location or a folder you select. Note the path of the downloaded file
on your computer. (Never download the file to your desktop.)
Ident
Power
Act
100
PXGMS UPS
Restart
TX
RX
Setup
CMN
Status
DHCP
EMP
Ethernet 10/100
+
-

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2 5
Section 3 Connect the Card to the Computer
To connect the card to the computer:
1. Plug the small connector at the end of the supplied USB configuration cable
into the setup port on the card (see Figure 3).
Figure 3. Install the USB Cable
2. Plug the other end of the USB cable into the USB port on the computer. The
Windows operating system detects new hardware.
Note: If a message indicates that the device driver software was not
successfully installed, click Ignore.
Note: You may see a pop-up message window that shows “Found new
hardware.” This indicates that the hardware installed successfully.
Ident
Power
Act
100
PXGMS UPS
Restart TX RX
Setup
CMN
Status
DHCP EMP
Ethernet 10/100
+
-

6 Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2
3. Connect an active Ethernet cable (not supplied) to the Ethernet 10/100
connector on the PXGMS card (see Figure 4).
Figure 4. Install the Ethernet Cable
4. Wait for the power light and status light on the installed card to illuminate.
This takes about two minutes.
5. Open a Web browser and type the default IP address (192.168.200.101).
6. Did the Power Xpert Gateway software open to the PXGMS page?
lIf yes, the driver has already been installed automatically. Either verify the
IP address assigned through DHCP or manually enter a static (fixed) IP
address for the card’s network connection:
a.To verify the DHCP-assigned IP address, go to page 13.
b.To manually enter a fixed IP address, go to page 16.
lIf no, the driver has not been installed. Go to the next section, "Install the
USB Driver Software" on page 7 in order to confirm that you have the most
current USB Driver software. If not, you need to install or update the USB
Driver software.
Ident
Power
Act
100
PXGMS UPS
Restart
TX
RX
Setup
CMN
Status
DHCP
EMP
Ethernet 10/100 +
-

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2 7
Section 4 Install the USB Driver Software
The steps you use to install the driver software depend on your operating system
(OS). This procedure provides instructions for installing driver software on a
Windows 7 OS.
Note: Windows 8 steps are basically the same as Windows 7, although the
dialog displays may differ somewhat.
Note: The PXGMS and PXGX UPS cards use the same driver.
Note: You can use either the Device Manager path or the Devices and Printers
path to browse for the driver software and install it. This procedure uses
the Device Manager.
To install the driver from the Device Manager:
1. C l i ck Start in the Start bar. Type Device in the search box.
2. Select Device Manager from the list above the search box. The Device
Manager opens.
3. Locate RNDIS/Ethernet Gadget under either Other Devices or Network
Adapters (see Figure 5).
lIf you do not see RNDIS/Ethernet Gadget in either list, you do not have a
cable connected to the card. Connect the computer to the card. Go back to
Step 1.
lIf RNDIS/Ethernet Gadget is listed under Other Devices, the driver is not
installed. Go to Step 4.
lIf RNDIS/Ethernet Gadget is listed under Network Adapters, a driver is
installed already, but you it may not be the most up to date driver. Go to
Step 4.

8 Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2
Figure 5. Device Manager Window
4. Right-click RNDIS/Ethernet Gadget to display the menu and select Update
Driver Software.
lIf a pop-up message displays, “The best driver is already installed,” click
Close and go to Step 10.
lOtherwise, go to Step 5.
5. Select Browse my computer for driver software (see Figure 6). Click
Next. The next page displays.
Figure 6. Update Driver Software Window – Search Method

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2 9
6. Click Browse. The “Browse for Folder” dialog displays. Select the folder that
contains drivers for your hardware. Click OK. The “Browse for driver
software on your computer” page displays.
7. The path to the powerxpert.inf file displays in the Search for driver
software in this location box. Click Browse and navigate to the
powerxpert.inf file you already downloaded. Select the file and click Next
(see Figure 7).
lIf a pop-up message displays, “The best driver is already installed,” click
Close and go to Step 10.
lOtherwise, the software begins to install.
Figure 7. Update Driver Software Window – Browse for Driver Software
Note: If the message “Windows can't verify the publisher of this driver
software” displays, select Install this driver software anyway
(see Figure 8).

10 Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2
Figure 8. Windows Security Message
8. When the driver software is updated successfully, the message “Windows
has successfully updated your driver software” displays (see Figure 9).
Figure 9. Update Driver Software Window – Update Successful
9. Click Close.
10. Either obtain the DHCP-assigned IP address or manually enter a fixed IP
address:
lTo obtain the IP address assigned through DHCP, continue to "Obtain a
DHCP-Assigned IP Address" on page 11.
lTo manually enter a static (fixed) IP address for the card’s network
connection, continue to "Assign an IP Address Manually" on page 15.
Note: By default, the PXGMS card requests an IP address through DHCP
when connected to a network.

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2 11
Section 5 Obtain a DHCP-Assigned IP Address
To obtain the IP address through DHCP:
1. Ensure the PXGMS card is still connected to the computer over the USB
cable. Also ensure that the network cable is connected from the PXGMS
card Ethernet port to the network connection.
2. If your Web browser already open to the default IP address, go to Step 3.
Otherwise, perform the following:
lOpen your Web browser.
lEnter: 192.168.200.101.
lLog on as administrator. The default username and default password are
“admin.” The PXGMS card Web page displays.
Note: If the system is unresponsive and you cannot make any selections, the
browser may be running in compatibility mode. To disable compatibility
mode, go to "Disable Browser Compatibility Mode" on page 18.
3. Select Network from the Configuration menu. The Network page displays
(see Figure 10).

12 Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2
Figure 10. PXGMS Card Network Page
4. Under IPv4, the Automatic Configuration: DHCP Enabled setting
checkbox should be enabled by default. Make sure the checkbox is checked
(enabled) before continuing.
5. Scroll down to Name Service and expand the selection to update the next
two DHCP settings (see Figure 11):
lCheck the checkbox (enable) for Use DHCP (when enabled) to get name
services.
lCheck the checkbox (enable) for Use DHCP (when enabled) to get
domain name.

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2 13
6. Click Apply.
Figure 11. Name Services Settings
7. Select Ye s for the message, “Do you want to save the Network
Configuration?”
8. Wait for approximately two minutes for the card to reboot. Initially, all lights
will be lit. You will know the card has finished rebooting when only the top
light (Status) and the bottom light (Power) remain lit.

14 Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2
9. Open a browser and enter the default IP address (192.168.200.101).
10. When prompted, log on as administrator. The default username and default
password are “admin.” The PXGMS card Web page displays.
11. Click Network in the menu list.
12. Does the DHCP-assigned IP address display?
lIf yes, uncheck (disable) the DHCP Enabled box and select Apply.
Note: At this point, the DHCP address is saved as a static IP address.
lIf no, go to "Assign an IP Address Manually" on page 15 to manually obtain
a static IP address for the PXGMS card.
Note: For detailed information, refer to the user’s guide for the Eaton Power
Xpert Gateway Minislot (PXGMS) User’s Guide, which is available
through a link on the Documentation tab on the PXGMS product Web
page.

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2 15
Section 6 Assign an IP Address Manually
To manually enter a static (fixed) IP address for the card:
1. Ensure the PXGMS card is still connected over the USB cable and the
network cable is connected from the PXGMS card Ethernet port to the
network connection.
2. If your Web browser already open, go to Step 3. Otherwise, perform the
following:
lOpen your Web browser.
lEnter: 192.168.200.101.
lLog on as administrator. The default username and default password are
“admin.” The PXGMS card Web page displays.
lGo to Step 3.
Note: If the system is unresponsive and you cannot make any selections, the
browser may be running in compatibility mode. To disable compatibility
mode, go to "Disable Browser Compatibility Mode" on page 18.
3. Select Network from the Configuration menu. The Network page displays.

16 Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2
Figure 12. Disable DHCP Setting
4. Uncheck the DHCP Enabled checkbox to disable DHCP and allow you to
manually configure the IP address (see Figure 12).
5. Refer to the "Installation Checklist" on page 2 in this book. Enter the IP
address, Netmask, and Gateway addresses in the IPv4 > Manual
Configuration section.
6. Click Apply, then click OK to confirm.
7. Optional. If you are using a host name, or host names, for controlling
access to the card:
lType the server IP address in the Name Server box. (Up to three IP
addresses can be entered.)
lClick Apply. Click OK to confirm.

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2 17
8. Open a browser and enter the fixed (static) IP address.
9. Log on as administrator. The default username and default password are
“admin.” When the PXGMS card Web page displays, you know the fixed IP
Address is working.
Note: For detailed information, refer to the user’s guide for the Eaton Power
Xpert Gateway Minislot (PXGMS) User’s Guide, which is available
through a link on the Documentation tab on the PXGMS product Web
page.

18 Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 2
Section 7 Disable Browser Compatibility Mode
Browser compatibility allows Web pages designed for older versions to display
properly. If data does not display properly on your PXGMS card Web page, the
browser compatibility mode should be disabled.
To disable the compatibility mode:
1. Open your Web browser.
2. In the Menu bar select Tools > Compatibility View Settings. The
Compatibility View Settings window opens (see Figure 13).
Figure 13. Compatibility View Settings Window