Eaton NZM2-XKSA Manual

Emergency On Call Service: Local representative (http://www.eaton.com/moeller/aftersales) or [phone] (de, en) 1/2
Electric current! Danger to life!
Only skilled or instructed persons may carry out the
following operations.
Lebensgefahr durch elektrischen Strom!
Nur Elektrofachkräfte und elektrotechnisch unterwiesene
Personen dürfen die im Folgenden beschriebenen Arbeiten
ausführen.
Tension électrique dangereuse !
Seules les personnes qualifiées et averties doivent
exécuter les travaux ci-après.
¡Corriente eléctrica! ¡Peligro de muerte!
El trabajo a continuación descrito debe ser realizado por
personas cualificadas y advertidas.
Tensione elettrica: Pericolo di morte!
Solo persone abilitate e qualificate possono eseguire le
operazioni di seguito riportate.
触电危险！
只允许专业人员和受过专业训练的人员进行
下列工作。
Электрический ток! Опасно для жизни!
Только специалисты или проинструктированные
лица могут выполнять следующие операции.
en
de
fr
es
it
zh
ru
Instruction Leaflet
Montageanweisung
Notice d’installation
Instrucciones de montaje
Istruzioni per il montaggio
安装说明
Инструкция по монтажу
11/10 IL01206007Z
(AWA1230-2047, AWA1230-2648)
NZM2(-4)-XKSA
Terminal cover for NZM2 Molded Case Circuit Breakers and Switches
-NA
-CNA
(UL/CSA models)
The barrier (shown shaded in the diagrams)
is held tightly into grooves on top and
bottom sides of the breaker or switch and
must be removed in order to mount the
NZM2(-4)-XKSA terminal cover.
To remove:
From the back of the device, use thumb
pressure to push, or an appropriate tool to
gently tap each side of the barrier to help
slide it out..
Caution!
The removal or exchange of parts during mounting may become necessary.
Refer to installation instructions for proper assembly and to maintain electrical
clearances.
Attenzione!
Per l’esecuzione degli interventi descritti potrebbe essere necessaria la rimozione o
sostituzione di alcuni pezzi. Attenersi alle istruzioni d’installazione per garantire dopo
l’assemblaggio le vie di dispersione necessarie.
Vorsicht!
Für die Durchführung der beschriebenen Arbeiten kann das Entfernen oder
der Austausch von Teilen notwendig sein.
Bitte alle Installations-Anweisungen beachten, um die erforderlichen Luft- und
Kriechstrecken nach dem Zusammenbau zu gewährleisten.
Attention !
L’enlèvement où l’échange de certaines pièces pendant le montage est parfois
nécessaire. Consultez l’instruction d’assemblage pour assurer une installation
conforme aux normes.
Осторожно!
При проведении описанных процедур может возникнуть необходимость
демонтировать или заменить детали. Для обеспечения надлежащих зазоров
и вывода тока утечки, соблюдайте все инструкции по монтажу.
¡Atención!
Con el fin de llevar a cabo los trabajos descritos, puede ser necesario eliminar
o cambiar alguna pieza. Le rogamos tenga en cuenta todas las instrucciones de
instalación para así garantizar las líneas de fuga y efluvio necesarias tras el montaje.
ON
Trip
push
en
it
de
zh
fr
ru
es

2/2 Emergency On Call Service: Local representative (http://www.eaton.com/moeller/aftersales) or [phone] (de, en)
11/10 IL01206007Z
Eaton Industries GmbH, Hein-Moeller-Straße 7-11, 53115 Bonn, Germany
© 2002 by Eaton Industries GmbH, www.eaton.com/moeller/support All Rights Reserved
11/10 IL01206007Z 12256581/DE17 DHW/DM
Printed in Germany (01/11)
jCombination options – Kombinationsmöglichkeiten – Combinaisons possibles – Combinaciones posibles – Combinazioni possibili – –
Комбинационные возможности
F415 V j+jj
F525 V j+jj+
F690 V j+j+j+
USE of Terminal Cover NZM2-XKSA on UL/CSA models:
– Terminal cover NZM2-XKSA maintains electrical clearances and provides protection against accidental contact
with live parts in the incoming and outgoing supply circuit terminations of the circuit breaker or switch.
– Top and bottom portions of the terminal cover are mounted as shown in preceeding diagrams.
– Use of the NZM2-XKSA terminal cover is always necessary with Type XKS screw terminations when making
connections with bare bus or non-insulated crimp lugs, or when two wires per phase are connected.
– Follow guidelines illustrated above for additional connection combinations.
1
ON
Trip
35
35
Z 2
1 Nm
(9 lb-in)
2
Minimum Clearance
space for all models
mm inch
35 1.4
4 x M4 x 85/20
3
2


1
Z 2
1.3 Nm
(11.5 lb-in)
Connector Type
NZM2-XKA
Compression
Crimp lugs
Use the terminal cover Type NZM2-XKSA
in all cases when making connections
with lug types pictured above.
Top and bottom portions of Terminal cover Type NZM2-XKSA shown shaded in above diagrams.
f400 mm
(f16”)
XKSA
XKSA
XKSA
XKSA
XKSA
XKSA