Eaton PXBCM-DISP-6-XV User manual

For detailed information concerning the operation and features avail-
able in the PXBCM meter display - 6” color touchscreen (PXBCM-
DISP-6-XV or PXBCM-DISP-6-TM-XV), please refer to PXBCM meter
color touchscreen display features (IB150023EN) or PXBCM meter
tenant meter touchscreen display features (IB150030EN) available on
the Eaton website (www.eaton.com/meters).
Figure 1. Color touchscreen display for PXBCM series meter.
Technical information
• 640 x 480 pixel backlit VGA touch screen display.
• Power: 24 Vdc input.
Effective November 2020
Supersedes June 2019
Technical Data TD150031EN
PXBCM meter color touchscreen
display quick start guide
Display measurements
• Height: 5.24 in. (133 mm);
• Width: 6.81 in. (173 mm);
• Depth: 1.54 in. (39 mm);
• Weight: 1.32 lb (600 g);
• Cutout dimensions: 4.61 in. x 6.18 in.(117.0 x 157.0 mm).
Ratings
• Front bezel IP rating: IP65;
• Operating temperature: 0 ~ 50°C (32 ~ 122°F);
• Storage temperature: -20 ~ 60°C (-4 ~ 140°F);
• Ambient humidity: 10% ~ 90% RH (0 ~ 40°C [32 ~ 104°F]),
10% ~ 55% RH (41 ~ 50°C [105.8 ~ 122°F]).
Figure 2. Dimensions of the PXBCM meter display - 6” color
touchscreen (PXBCM-DISP-6-XV).

2
Technical Data TD150031EN
Effective November 2020
PXBCM meter color touchscreen
display quick start guide
EATON www.eaton.com
Installation
1. Disconnect and lockout all power to the enclosure.
2. Inspect the enclosure door to determine the best mounting loca-
tion for the PXBCM meter color touchscreen display.
ote:N A minimum clearance of 1.18 in. (30.0 mm) must be maintained
between the ventilation holes in the back of the display and any other
component within the enclosure.
3. Use the mounting template to mark the cutout area on the enclo-
sure door. Cut out the marked area.
Figure 3. Cut out dimensions.
4. Insure proper gasket placement on the PXBCM meter color
touchscreen display.
5. Insert the PXBCM meter color touchscreen display through the
cutout.
6. Fit the supplied threaded pins in the retaining brackets. The tips
of the threaded pins must point towards the wider ends of the
retaining brackets. Clip on the retaining brackets in the recesses
provided for them on the device.
Figure 4. Mounting the PXBCM meter display.
7. Check for proper alignment of the PXBCM meter color touch-
screen display. Then fix the device by torquing the threaded pins
to 0.1 Nm (0.86 lb-in) with a 2mm hexagonal screwdriver. The
front of the display should be flush with the surface of the con-
trol cabinet at the fixing points.

3
Technical Data TD150031EN
Effective November 2020
PXBCM meter color touchscreen
display quick start guide
EATON www.eaton.com
Figure 5. Power and COM port connections for the PXBCM meter display touch screen display.
Connections
To use the PXBCM meter color touchscreen display, provide 24 Vdc
and connect the power cable between the PXBCM color touch-
screen display and the PXBCM-MB meter.
The display’s plug-in terminals provide connections for +24, GND
and Common (0). Included with the PXBCM meter color touchscreen
display is a data cable to connect DB9 of the color touchscreen dis-
play to 3-terminal COM 1 or 2 (RS485) of the PXBCM meter base.
For best results, use the default communication settings for the
PXBCM color touchscreen display (38.4 kbps, 1 start bit, 1 stop bit,
no parity). In applications requiring both COM ports, COM 2 is rec-
ommended for the display.
ote:N By default, the PXBCM color touchscreen display is preset for a
PXBCM meter base Modbus address of “01”. To accommodate a different
Modbus address, the user MUST change the PXBCM meter color touch-
screen display’s “Modbus ID”.
Figure 6. Changing the Modbus ID.
5 4 3 2 1
9 8 7 6
Eaton P/N 67A2186HXX
YY-MM-DD
2.0"
H11 = 48"
H12 = 144"
PIN 1
PIN 1
PIN 2
BARE
BLACK
RED
PIN 1
PIN 3 WHITE
PHOENIX CONN.
TERMINATION
RED
BLACK
WHITE
DB9 SHELL
DB9 TERMINATION
PIN 3
PIN 5
PIN 7
H11/H12
SHIELD WIRE TERMINATED to
(XV)
PXBCM-MB
PXBCM-DISP-6-XV
Lorem ipsum
67A2186H11/H12

Technical Data TD150031EN
Effective November 2020
PXBCM meter color touchscreen
display quick start guide
Eaton
Electrical Sector
1000 Eaton Boulevard
Cleveland, OH 44122
United States
877-ETN-CARE (877-386-2273)
Eaton.com
© 2020 Eaton
All Rights Reserved
Printed in USA
Publication No. TD150031EN / TBG001462
November 2020
Eaton is a registered trademark.
All other trademarks are property of their
respective owners.
Firmware updates
Eaton periodically releases firmware updates with feature enhance-
ments and stability improvements.
To update the firmware on the display, one of the following two
methods can be used:
USB drive, keyboard and mouse
1. Download the firmware update file from eaton.com\meters. Save
to a flash drive and unzip the folder.
2. Press the CTRL button on the right side of the display to exit the
application.
3. Under the display’s MyDevice, copy the UsbStorage\
InternalStorage folder (Edit > Copy).
4. Again, under MyDevice, delete the existing InternalStorage (File
> Delete).
5. Paste the new InternalStorage (Edit > Paste). This transfers the
firmware from the flashdrive to the display. Expect the transfer
to take 2 minutes. For files that already exist, select “Yes to All”
so that they are overwritten.
6. Power cycle the display.
7. On boot-up, enter the 7-character authentication code that is
printed on a label on the back of the display (see Figure 9). Click
Return. The authentication box will turn from red to green.
8. Click Save.
9. Double-click the GRS-CE5 to start the application (or, alternatively,
cycle power the display).
PC and ethernet cable
1. Download the firmware update file from eaton.com. Save to the
PC. Unzip the folder.
2. Press the CTRL button on the right side of the display to exit the
application.
3. On the display, select Start > Settings > Network and Dial-up
Connections. Double-click “ONBOA…” to see the Display’s
Ethernet connection IP address. Verify that this is 192.168.1.1. If
it is not, edit the fields and click OK.
4. Attach Ethernet cable between the display and PC.
5. Set the PC’s Ethernet address to be compatible with the display
(e.g. 192.168.1.99).
6. On the PC, use Windows File Explorer navigate to the down-
loaded firmware upgrade files so that the InternalStorage folder
appears.
Figure 7. Internal storage.
7. Open another instance of Windows File Explorer address bar,
type “ftp://192.168.1.1“ (or the display’s Ethernet connection IP
address from step 3). This will show the file structure in the dis-
play.
Figure 8. Example with display set for 192.168.1.98 and PC set
for 192.168.1.99.
8. All firmware goes into the InternalStorage folder.
9. Delete the existing InternalStorage folder (OS and runtime fold-
ers are likely protected).
10. With a mouse, drag the InternalStorage folder from the firmware
update (step 6) to the FTP pane. Expect the transfer to take 2
minutes. For files that already exist, select “Yes to All” so that
they are overwritten.
11. Power cycle the display.
12. Enter the 7-character authentication code that is printed on a
label on the back of the display (see Figure 9). Click Return. The
authentication box will turn from red to green.
13. Click Save.
14. Double-click the GRS-CE5 to start the application (or, alterna-
tively, cycle power the display).
Figure 9. Example authorization code label on rear of display.
Serial number:
10140011462
Auth: 7138063
Serial number
from rear
of display
Authorization code