Eaton 9PX2000RT-L Assembly instructions

p/n: P-164001006
Revision 02
9PX1500RT-L
9PX2000RT-L
9PX3000RT-L
9PX1500GRT-L
9PX2200GRT-L
9PX3000GRT-L
9PXEBM48RT-L
9PXEBM72RT-L
Advanced Users Guide
Eaton 9PX Lithium-Ion

©Copyright 2023 Eaton, Raleigh, NC, U A. All rights reserved. No part of this document may be reproduced in any way without the
express written approval of Eaton.
SSaaffeettyy IInnssttrruuccttiioonnss
SAVE THESE INSTRUCTIONS.
This manual contains important instructions that should be followed during installation and
maintenance of the UPS and batteries.
The 9PX models that are co ered in this manual are intended for installation n an en ironment within 0
to 40°C, free of conducti e contaminant.
This equipment has been tested and found to comply with the limits for a Class B digital de ice,
pursuant to IEC62040-2 & FCC standards. These limits are designed to pro ide reasonable protection
against harmful interference when the equipment is operated in a commercial en ironment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
SSppeecciiaall SSyymmbboollss
The following are examples of symbols used on the product to alert you to important information:
RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock
symbol.
CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's manual for
additional information, such as important operating and maintenance instructions.
This symbol indicates that you should not discard the UP or the UP batteries in the trash.
This product contains sealed, Lithium-Ion batteries and must be disposed of properly. For
more information, contact your local recycling/reuse or hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic equipment
(WEEE) in the trash. For proper disposal, contact your local recycling/reuse or hazardous
waste center.

SSaaffeettyy ooff PPeerrssoonnss
• The system has its own power source (the battery). Consequently, the power outlets may be
energized en if the systems is disconnected from the AC power source. Dangerous oltage
le els are resent within the system. It should be opened exclusi ely by qualified ser ice
personnel.
• The system must be properly grounded at all times.
• The battery supplied with the system contains small amounts of toxic materials. To a oid
accidents, the directi es listed below must be obser ed:
–Ser icing of batteries should be performed or super ised by personnel knowledgeable about
batteries and the required precautions.
–When replacing batteries, replace with the same type and number of batteries or battery
packs.
–Do not dispose of batteries in a fire. The batteries may explode.
–Batteries constitute a danger (electrical shock, burns). The short-circuit current may be ery
high.
• Precautions must be taken for all handling:
–Wear rubber glo es and boots.
–Do not lay tools or metal parts on top of batteries.
–Disconnect charging source prior to connecting or disconnecting battery terminals.
–Determine if battery is inad ertently grounded. If inad ertently grounded, remo e source
from ground. Contact with any part of a grounded battery can result in electrical shock. The
likelihood of such shock can be reduced if such grounds are remo ed during installation and
maintenance (applicable to equipment and remote battery supplies not ha ing a grounded
supply circuit).
PPrroodduucctt SSaaffeettyy
• To connect the UPS, instructions and operation described in the manual must be followed in the
indicated order.
• CAUTION - To reduce the risk of fire, the unit connects only to a circuit pro ided with 20 or 30
amperes maximum branch circuit o ercurrent protection in accordance with the National Electric
Code, ANSI/NFPA 70 (US installations only).
• Check that the indications on the rating plate correspond to your AC powered system and to the
actual electrical consumption of all the equipment to be connected to the system.
• For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall
be easily accessible
• Ne er install the system near liquids or in an excessi ely damp en ironment.
• Ne er let a foreign body penetrate inside the system.
• Ne er block the entilation grates of the system.
• Ne er expose the system to direct sunlight or source of heat.
• If the system must be stored prior to installation, storage must be in a dry place.
• The admissible storage temperature range is -25ºC to +55ºC without batteries, 0°C to 40°C with
batteries.
• The system is not for use in a computer room AS DEFINED IN the standard for the Protection of
Information Technology Equipment, ANSI/NFPA 75 (US installations only).

SSppeecciiaall PPrreeccaauuttiioonnss
• The unit is hea y: wear safety shoes and use acuum lifter preferentially for handling operations.
• All handling operations will require at least two people (unpacking, lifting, installation in rack
system).
• Before and after the installation, if the UPS remains de-energized for a long period, the UPS must
be energized for a period of 24 hours, at least once e ery 6 months (for a normal storage
temperature less than 25°C). This charges the battery, thus a oiding possible irre ersible
damage.
• During the replacement of the Battery Module, it is imperati e to use the same type and number
of element as the original Battery Module pro ided with the UPS to maintain an identical le el of
performance and safety. If there are any questions, don’t hesitate to contact your local EATON
representati e.
• All repairs and ser ice should be performed by AUTHORIZED SERVICE PERSONNEL ONLY.
There are NO USER SERVICEABLE PARTS inside the UPS.
• For potential safety issue on defecti e UPS : DISCONNECT INTERNAL BATTERY for storage and
transportation.

Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02 v
TTaabbllee ooff CCoonntteennttss
11 IInnttrroodduuccttiioonn....................................................................................................................................................................................................................................................................................................11
1.1 Introduction...............................................................................................................................................1
1.2 En ironmental Protection ............................................................................................................................. 1
22 PPrreesseennttaattiioonn ..................................................................................................................................................................................................................................................................................................33
2.1 Standard Installations ..................................................................................................................................3
2.2 Rear Panels...............................................................................................................................................4
2.3 Accessories...............................................................................................................................................5
2.4 Control Panel.............................................................................................................................................5
2.5 LCD Description.........................................................................................................................................7
2.6 Display Functions .......................................................................................................................................8
2.7 User Settings.............................................................................................................................................9
33 IInnssttaallllaattiioonn .................................................................................................................................................................................................................................................................................................. 1155
3.1 Inspecting the Equipment........................................................................................................................... 15
3.2 Checking the Accessory Kit ........................................................................................................................ 15
3.3 Connecting the Internal Battery ................................................................................................................... 17
3.4 Tower Installation ..................................................................................................................................... 18
3.5 Rack Installation ....................................................................................................................................... 19
3.6 Connecting the EBM(s) .............................................................................................................................. 20
3.7 Detecting other Accessories ....................................................................................................................... 21
3.8 UPS Connection without Hotswap MBP Module ............................................................................................. 22
3.9 Connection with a Hotswap MBP Module ( Optional Accessory)......................................................................... 23
44 CCoommmmuunniiccaattiioonn ...................................................................................................................................................................................................................................................................................... 2255
4.1 Communication Ports................................................................................................................................ 25
4.2 UPS Remote Control Functions ................................................................................................................... 26
55 OOppeerraattiioonn........................................................................................................................................................................................................................................................................................................ 3311
5.1 Start-up and Normal Operation .................................................................................................................... 31
5.2 Starting the UPS on Battery ........................................................................................................................ 31
5.3 UPS Shutdown ........................................................................................................................................ 31
5.4 Operating Modes ..................................................................................................................................... 31
5.5 Return of AC Power .................................................................................................................................. 32
5.6 Setting High Efficiency Mode ...................................................................................................................... 32
5.7 Configuring Bypass Settings ....................................................................................................................... 33
5.8 Configuring Battery Settings ....................................................................................................................... 33
5.9 Retrie ing the E ent Log ............................................................................................................................ 34
5.10 Retrie ing the Fault Log ........................................................................................................................... 34
66 UUPPSS aaiinntteennaannccee................................................................................................................................................................................................................................................................................ 3355
6.1 Storing the Equipment............................................................................................................................... 35

vi Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02
6.2 Replacing Batteries ................................................................................................................................... 35
6.3 Battery Settings Reset............................................................................................................................... 37
6.4 Replacing the UPS Equipped with a HotSwap MBP ......................................................................................... 39
6.5 Recycling The Used Equipment ................................................................................................................... 39
77 TTrroouubblleesshhoooottiinngg .................................................................................................................................................................................................................................................................................... 4411
7.1 Typical Alarms and Faults ........................................................................................................................... 41
7.2 Silencing the Alarm ................................................................................................................................... 42
7.3 Ser ice and Support .................................................................................................................................. 42
7.4 CE Compliance Contact ............................................................................................................................. 43
88 SSppeecciiffiiccaattiioonnss.......................................................................................................................................................................................................................................................................................... 4455
8.1 Model Specifications................................................................................................................................. 45
Table of Contents

Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02 1
CChhaapptteerr 11 IInnttrroodduuccttiioonn
11..11 IInnttrroodduuccttiioonn
Thank you for selecting an Eaton Tripp Lite SmartOnline series product to protect your electrical equipment.
The Eaton Tripp Lite SmartOnline series range has been designed with the utmost care.
We recommend that you take the time to read this manual to take full ad antage of the many features of your
UPS (Uninterruptible Power System).
Before installing your Eaton Tripp Lite SmartOnline series, please read the booklet presenting the safety
instructions. Then follow the indications in this manual.
To disco er the entire range of Eaton Tripp Lite SmartOnline series products and the options a ailable for the
Eaton Tripp Lite SmartOnline series range, we in ite you to isit our web site at Eaton Tripp Lite.com or contact
your Eaton Tripp Lite SmartOnline series representati e.
11..22 EEnnvviirroonnmmeennttaall PPrrootteeccttiioonn
EATON has implemented an en ironmental-protection policy.
Products are de eloped according to an eco-design approach.
Substances
This product does not contain CFCs, HCFCs, or asbestos.
Packing
To impro e waste treatment and facilitate recycling, separate the arious packing components.
• The cardboard we use comprises o er 50% of recycled cardboard.
• Sacks and bags are made of polyethylene.
• Packing materials are recyclable and bear the appropriate identification symbol
01
PET
Tabl 1. Packing Mat rial Symbols
Mat rials Abbr viations Numb r in th symbols
Polyethylene terephthalat PET 01
High-density polyethylene HDPE 02
Polyvinyl chloride PVC 03
Low-density polyethylene LDPE 04
Polypropylene PP 05
Polystyrene P 06
Follow all local regulations for the disposal of packing materials.
End of Life
Eaton will process products at the end of their ser ice life in compliance with local regulations. Eaton works
with companies in charge of collecting and eliminating our products at the end of their ser ice life.
Product

2 Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02
The product is made up of recyclable materials.
Dismantling and destruction must take place in compliance with all local regulations concerning waste. At the
end of its ser ice life, the product must be transported to a processing center for electrical and electronic
waste.
Battery
The product contains lithium-ion (LFP) batteries that must be processed according to applicable local
regulations concerning batteries.
The battery may be remo ed to comply with regulations and in iew of correct disposal.
The Eaton® 9PX uninterruptible power system (UPS) protects your sensiti e electronic equipment from the
most common power problems, including power failures, power sags, power surges, brownouts, line noise,
high oltage spikes, frequency ariations, switching transients, and harmonic distortion.
Power outages can occur when you least expect it and power quality can be erratic. These power problems
ha e the potential to corrupt critical data, destroy unsa ed work sessions, and damage hardware causing hours
of lost producti ity and expensi e repairs.
With the Eaton 9PX, you can safely eliminate the effects of power disturbances and guard the integrity of your
equipment. Pro iding outstanding performance and reliability, the Eaton 9PX’s unique benefits include:
• True online double-con ersion technology with high power density, utility frequency independence, and
generator compatibility.
• Constant mode battery charger with a integrated battery management system (BMS) for temperature
regulation and life cycle monitoring.
• Selectable High Efficiency mode of operation.
• Standard communication options: one RS-232 communication port, one USB communication port, and
relay output contacts.
• Optional connecti ity cards with enhanced communication capabilities.
• Extended runtime with up to four Extended Battery Modules (EBMs) per UPS.
• Remote On/Off control through Remote On/Off (ROO) and Remote Power Off (RPO) ports.
• Backed by worldwide agency appro als.
Environmental Protection

Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02 3
CChhaapptteerr 22 PPrreesseennttaattiioonn
22..11 SSttaannddaarrdd IInnssttaallllaattiioonnss
Figure 1. Tower Installation
D
W
H
Figure . Rack Installation
D
H
W
Tabl 2. W ights and Dim nsions
Mod l Dim nsions D x W x H(inch/mm) W ight (lb / kg)
9PX1500RT-L 17.7 x 17.3 x 3.4 / 450 x 440 x 86.5 35.5 / 16.2
9PX2000RT-L 23.8 x 17.3 x 3.4 / 605 x 440 x 86.5 50.6 / 23.0
9PX3000RT-L 23.8 x 17.3 x 3.4 / 605 x 440 x 86.5 52.7 / 24.0
9PX1500GRT-L 17.7 x 17.3 x 3.4 / 450 x 440 x 86.5 34.8 / 15.8
9PX2200GRT-L 23.8 x 17.3 x 3.4 / 605 x 440 x 86.5 48.6 / 22.1
9PX3000GRT-L 23.8 x 17.3 x 3.4 / 605 x 440 x 86.5 50.2 / 22.8
9PXEBM48RT-L 17.6 x 17.2 x 1.7 / 448 x 438 x 42.9 36.5 / 16.6
9PXEBM72RT-L 23.7 x 17.2 x 1.7 / 603 x 438 x 42.9 46.6 / 21.2

4 Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02
22..22 RReeaarr PPaanneellss
9PX 1500RT-L
1 2 3 4 5 6
9 811 10 7
9PX 2000RT-L
1 82 43 5 6
9 1011 7
9PX 1500GRT-L
9PX 3000RT-L (*)
1 82 43 5 6
9 1011 7
9PX 2000GRT-L & 9PX 3000GRT-L
1Socket for connection to AC power
source
2Slot for optional communication card
3Relay output contact
4Connector for additional battery
module
5Primary group: outlets for
connection of critical equipment
6Group 1: programmable
outlets for connection of equipment
7Group 2: programmable
outlets for connection of equipment
8Connector for automatic recognition
of an additional battery module
9RS232 communication port
10 USB communication port
11 Connector for ROO (Remote On/Off)
control and RPO (Remote Power Off)
(*) Primary and Grouped outlets
(5, 6, 7) are protected by 20A
circuit breakers.
1 82 4 53
9 1011 6 7
1 2 3 4 5
9 811 10 6 7
Rear Panels

Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02 5
9PXEBM48RT-L
13
12
12 Connectors for battery modules
(to the UPS or to the other battery
modules)
13 Connectors for automatic recognition
of battery modules
9PXEBM72RT-L
12
13
12 12
22..33 AAcccceessssoorriieess
Tabl 3. UPS Acc ssori s
Part numb r D scription
9PXEBM48RT-L
9PXEBM72RT-L Extended Battery Module
9RK Rack Kit 9PX
Network-M2 / Network-M3 Network Card
INDGW-M2 Industrial Gateway Card (Modbus TCP / RTU)
Relay-M Relay Card
22..44 CCoonnttrrooll PPaanneell
The UPS has a fi e-button graphical LCD. It pro ides useful information about the UPS itself, load status, e ents,
measurements and settings.
Accessories

6 Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02
Online mode
indicator (green)
Fault
indicator (red)
Online mode
100%
19min
1EBM
100%
2.4kW
3.0kVA
Efficiency: 94 %
Escape Up Down Enter On/Off
button
Battery mode
indicator (orange)
Bypass mode
indicator (orange)
Indicator Status D scription
Green
On The UP is operating normally on Online
or on High Efficiency mode.
Orange
On The UP is on Battery mode.
Orange
On The UP is on Bypass mode.
Red
On The UP has an active alarm or fault.
Control Panel

Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02 7
22..55 LLCCDD DDeessccrriippttiioonn
Figure 3. LCD Description
Operation status
Load/equipment status
Online mode
100%
19min
1EBM
100%
2.4kW
3.0kVA
Efficiency: 94%
Battery status
Efciency and load group information
The following table describes the status information pro ided by the UPS
Note: If other indicator appears, see the troubleshooting for additional information.
Tabl 4. LCD Op rating Status
Op ration status Caus D scription
tandby mode The UP is Off, waiting for startup
command from user. Equipment is not powered until
button is pressed.
Online mode The UP is operating normally. The UP is powering and protecting the
equipment.
Battery mode A utility failure has occured and the UP
is on Battery mode.
The UP is powering the equipment with
the battery power. Prepare your
equipment for shutdown.
End of backup time The UP is on Battery mode and the
battery is running low.
Low Battery Warning settings:
[Capacity] [0%] ... [100%]
[Runtime] [0mn] ... [60mn]
The alarm triggers when the set
percentage of battery capacity or
remaining back-up time is reached.
LCD Description

8 Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02
Tabl 4. LCD Op rating Status (Continu d)
Op ration status Caus D scription
High Efficiency mode The UP is operating on High Efficiency
mode.
The UP is powering and protecting the
equipment
Bypass mode An overload or a fault has occurred, or a
command has been received, and the
UP is in Bypass mode.
Equipment is powered but not protected
by the UP .
22..66 DDiissppllaayy FFuunnccttiioonnss
Press the ( ) button to acti ate the menu options. use the two middle buttons ( and ) to scroll through
the menu structure. Press the ( ) button to select an option. Press the ESC button to cancel or return to the
pre ious menu.
Tabl 5. Display Functions
Main m nu Subm nu Display information or M nu function
Measurements [Load] W VA A pf / [Input/Output] V Hz /
[Efficiency] % / [Battery] % min V n°
EBM / [Battery remaining life] months /
[Average power usage] Wh / [Cumulated
power] Wh / BM Information
Control Go to Bypass Transfers the UP on Bypass mode
Load segments On/Off Commands the load segments
tart battery test tarts a manual battery test
Connectivity test Tests dry contact relay outputs and relay
card contacts. imulates line failure and
battery low
Function reset Clears active fault, power usage, battery
remaining life, reset NMC, Restore
factory settings.
ettings Local settings ets product general parameters
In/out settings ets Input and Output parameters
On/Off settings ets On/Off conditions
Battery settings ets battery configuration
Com settings ets communication parameters
Event Log Event filter elects faults, alarms and/or events to
display
Event list Displays the events stored
Reset fault list Clears events
Display Functions

Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02 9
Tabl 5. Display Functions (Continu d)
Main m nu Subm nu Display information or M nu function
Fault log Fault list Displays the faults stored
Reset fault list Clears faults
Identification [Product type/model] / [Part/ erial
number] / [UP /NMC firmware] / [Com
card IPv4], [Com card IPv6], [Com card
MAC]
Registration Links to Eaton registration website
22..77 UUsseerr SSeettttiinnggss
The following table displays the options that can be changed by the user.
Tabl 6. Us r S ttings
Subm nu Availabl S ttings D fault s ttings
Local ettings
Language [English] [Français] [Deutsch]
[Español] [Русский]
[Português] [Italiano]
[ implified Chinese]
[Japanese] Menus, status,
notices and alarms, UP fault,
Event Log data and settings
are in all supported
languages.
[English] User selectable
when UP is powered for the
first time.
Date/ time Format: [International] [U ] [U ]
LCD Modify LCD screen brightness
and contrast to be adapted to
room light conditions.
Audible alarm Mode: [Enabled] [Disabled on
battery] [Always disabled]
Enable or disable the buzzer if
an alarm occurs. Level: [High]
[Low]
[Enabled] [High]
Protected access [Enabled] [Disabled] Password
is: 0577
[Disabled]
In/Out settings
Output voltage 100V] [110V] [120V] [125V] [120V]
[200V] [208V] [220V] [230V]
[240V]
[208V]
Output frequency Mode: [Normal] [Converter]
[Marine] Frequency can be
changed in Frequency
[Converter] mode In [Marine]
mode output frequency
follows input frequency
[Normal]
User ettings

10 Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02
Tabl 6. Us r S ttings (Continu d)
Subm nu Availabl S ttings D fault s ttings
Output mode Mode: [Industrial] [IT]
[Custom] Overload: [Inv> top]
[Inv>BP] [Inv>BP>Inv]
[IT] [Inv>BP>Inv] [Inv> top]
hort-circuit: [Inv> top]
[Inv>BP]
[Inv>BP>Inv]
Input volt hysteresis ets input voltage hysteresis
from [1] to |10V]
[10V]
High Efficiency mode [Enabled] [Disabled] Power the
output from Bypass for high
efficiency
[Disabled]
Bypass settings [Volt low] [80V] LV; [160V] HV;
[Volt high] [144V] LV; [276V] HV;
[Qualify] [In spec];
[Hz synch] [5%];
[Unsynch] [Half cycle]
Load segments [Auto start delay] UP : [0s]; Group1: [3s];
Group2: [6s] UP : [Disabled];
[Auto shutdown delay] Group1: [Disabled]; Group2:
[Disabled]
Overload prealarm [10%] … [102%] Load %
when overload alarm occurs
[102%]
On/Off ettings
tart/Restart [Cold start] [Auto restart]
[Auto start] [ tart on bypass]
[Cold start] [Auto restart] are
Enabled
[Auto start] [ tart on bypass]
are Disabled
Forced reboot [Enabled] [Disabled] [Enabled]
[Timer] [10s] … [180s] [10s]
When mains recover during a
shutdown sequence: If set to
Enabled, shutdown sequence
will complete and wait 10
seconds prior to restart, If set
to Disabled, shutdown
sequence will not complete,
UP stays on.
Energy saving [Enabled] [Disabled] [Disabled]
[Timer] [1min] … [15min] [5min]
[Level] [100W] … [1000W] [100W]
User ettings

Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02 11
Tabl 6. Us r S ttings (Continu d)
Subm nu Availabl S ttings D fault s ttings
If Enabled, UP will shut-
down after defined duration.
of back-up time, if load is less
than set value.
leep mode [Enabled] [Disabled] [Enabled]
[Timer] [10min] … [120min]
If Disabled, LCD and
communication will turn OFF
immediately after UP is OFF.
[90min]
If Enabled, LCD and
communication stays ON 1h30
min after UP is OFF.
ite wiring fault [Enabled] [Disabled] [Disabled]
Prevents from starting the
UP in case of phase vs
neutral wires swapping.
Power Off alert [Enabled] [Disabled] [Enabled]
If Enabled, activates a
confirmation screen that
requires user confirmation
after pressing the power
button, before the UP
shutdown occurs.
Battery settings
Low battery warning [Capacity] [0%] … [100%] [0%]
[Runtime] [0min] … [60min] [3min]
The alarm triggers when the
set percentage of battery
capacity or remaining back-up
time is reached.
Restart bat. level [0%] ... [100%] [0%]
If set, automatic restart will
occur only when percentage
of battery charge is reached.
Com settings Input signals
ets Input signals parameters
(function, delay, operation)
through external contact
connectors or R 232.
ROO port:
- [Function]: [No] [ROO] [RPO]
[Building alarm] [Forced
bypass] [On generator]
[Remote shutdown]
[No]
User ettings

12 Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02
Tabl 6. Us r S ttings (Continu d)
Subm nu Availabl S ttings D fault s ttings
- [Delay]: [0s] … [999s] [0s]
- [Active]: [Open] [Closed] [Closed]
RPO port:
- [Function]: [No] [ROO] [RPO]
[Building alarm] [Forced
bypass] [On generator]
[Remote shutdown]
No
- [Delay]: [0s] … [999s] [0s]
- [Active]: [Open] [Closed] [Open]
DB9-4 port: No
- [Function]: [No] [ROO] [RPO]
[Building alarm] [Forced
bypass] [On generator]
[Remote shutdown]
- [Delay]: [0s] … [999s] [0s]
- [Active]: [High] [Low] [High]
Output signals
[Relay] [DB9-1] [DB9-7] [DB9-
8] ets events or fault that
will actuate Output signal
parameters through external
contact connector or R 232
[Relay]: [On bat] [Low bat] [Bat
fault] [Bypass] [UP OK] [Load
protected] [Load powered]
[General alarm] [Ext. charger
ON] [OVL pre-alarm]
[Relay] [Bypass]
[DB9-1]: [On bat] [Low bat]
[Bat fault] [Bypass] [UP OK]
[Load protected] [Load
powered] [General alarm] [Ext.
charger ON] [OVL pre-alarm]
[DB9-1] [Low bat]
[DB9-7]: [On bat] [Low bat]
[Bat fault] [Bypass] [UP OK]
[Load protected] [Load
powered] [General alarm] [Ext.
charger ON] [OVL pre-alarm]
[DB9-7] [UP OK]
[DB9-8]: [On bat] [Low bat]
[Bat fault] [Bypass] [UP OK]
[Load protected] [Load
powered] [General alarm] [Ext.
charger ON] [OVL pre-alarm]
[DB9-8] [On bat]
Com settings (cont) Remote command [Enabled] [Disabled] If
Enabled, shutdown or restart
[Enabled]
User ettings

Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02 13
Tabl 6. Us r S ttings (Continu d)
Subm nu Availabl S ttings D fault s ttings
commands from software are
authorized.
hutdown commands [ end CMD] [Output OFF] [OFF
delay] [restart]
ets events or fault that will
actuate Output signal
parameters through external
contact connector or R 232
port
[ end CMD]: [Yes] [No] end CMD: [No]
[Output OFF]: [No] [UP ]
[Group 1]
Output OFF: [No]
[Group 2] [Group 1 + Group 2]
[OFF delay]: [0s] …[999s] OFF delay: [0s]
[Restart]: [Yes] [No] Restart: [Yes]
On battery notice delay ets delay before noticing on
battery information to
software.
[0s]
General alarm [On battery] [Battery fault] [Internal fault]
[Overload pre-alarm] [Internal
fault]
[Ambient temp.] [Fan lock]
[Bypass overload] [Current
limit]
[ hort circuit] [Inverter
overload]
[Power overload] [Low battery]
[On bypass] [UP OK] [Load
protected]
[Load powered] [Ext. charger
ON]
Defines which event or fault
generate
a general alarm through
Output signal screen.
User ettings

14 Eaton 9PX Lithium-Ion User Guide P-164001006—Rev 02
User ettings