EBN Technology TM 120 User manual

TM Series
Quick Guide

Chapter 1
Introduction
1.1 About the Products
1.2 Specification
Chapter 2
Hardware Setup
2.1 Unpacking Touch monitor
2.2 Product Overview
2.3 Main Unit
2.4 Rear View
2.5 Internal layout
2.6 MSR Installation
2.7 Customer Display Installation
Chapter 3
Driver Installation
3.1 Installing the touch driver
3.2 Installing the MSR Utility
Chapter 4
OSD Operation
4.1 On-Screen Display (OSD) Menus

Chapter 1
Introduction
1.1 About the Products
The LCD Desktop Touch monitor is a 12” / 15” TFT color display with the following
features:
- Direct analog screen input
- 167 million displayable colors
- High resolution
- XGA / SVAGA / VGA / VESA / Mac compatible
- 30 ~ 62KHz horizontal scan
- 56 ~ 75 HZ refresh rate
- Auto adjustment capability
- High quality full screen re-scaling
- Multilingual OSD menus: English, French, Germany, Spanish, Japanese and
Chinese.
- Serial / USB touch interface
- Built in speakers
- Optional Fujitsu / Higgstec touch panel.
- VESA DDC 1/28B data communication
- Stand with minimum 20 ~ 90° angle of tilt.
- OSD and power button lockouts

1.2 Specification
Display
Model TM150 TM120
LCD Size 15" 12.1"
Brightness 250 cd/m2 300 cd/m2
Resolution 1024x768 800x600
Touch Screen 5 / 7-wire Resistive Type
Tilt Angle 20° to 90°
I/O Ports
VGA 15pin D-SUB x1
Serial RS232 x 2 ( For Touch Panel / MSR & I-Button Key )
PS2 Keyboard 1 (For MSR & I-Button)
Speaker Internal 2W x2
Others
Power Supply Internal Adapter 12VDC, 50W
Compliance CE / FCC Class B
Weight Approx. 6.0 Kgs
Dimension 370(W) x 277(L) x 355(H)
mm
313(W) x 274(L) x 318(H)
mm
Operating
Temp
5°C to 40°C

Chapter 2
Hardware Set up
2.1 Unpacking the touch monitor
Check that the following 4 items are presented and in good conditions:
a. Main Unit
b. CD: Quick Guide & Driver Bank
c. Power Cord: USA, Europe, UK

d. Option Item
d1. Customer Display: RS232 port, pin 9 was power input 12VDC.
d2. MSR (Magnetic Stripe Reader): 2/3 tracks, KB / RS232 option.
d3. MSR and I-BOTTOM: 2 in 1 Module, MSR with Dallas Key Reader.

2.2 Product Overview
a. Front View
ControlPad:Power button, Menu select, + - Key Adjust, Auto Set
b. Rear View
1. Power cable: 110V/220V
2. VGA cable (15 pin D Sub): Connect with VGA port of PC.
3. Touch cable (COM, 9 pin D Sub): Connect with RS232 port of PC.
4. MSR (Optional, COM, 9 pin D Sub) - Connect with RS232 port of PC.
5. Touch USB (Optional) - Connect with USB port of PC.
6. MSR (Optional, Keyboard) – Connect with PC Keyboard self and Keyboard port
7. Audio Input.

c. Internal Layout
1. USB: optional touch control board connection.
2. COM1 for standard touch control board.
3. COM2 for optional RS232 type MSR.
4. PS2 for optional Key Board type MSR.
5. VGA.
6. AUDIO in.
7. POWER in.
d. MSR Installation
d1. Release the 2 screws of main body from rear side of bezel.

d2. Disassembly EMI Chassis & Cable Clipper, insert and connect the MSR cable.
Then recover the Chassis and Cable Clipper.
d3. Remove the MSR cover on right side of monitor. Install the MSR module by 3
screws. Finally connect the MSR cable to CN1( refer to Internal Layout ).

e. Customer Display Installation
Remove the cover pad, then install the pole tube and customer display, connect
the cable with the RS232 port (pin 9 with 12V) of PC.