ECCB OUTDOOR Adirondack User manual

966 Perry Highway, Mercer, PA 16137 • Phone [phone]
ECCBOutdoor.com
Important
Please Read All Instructions Carefully Before Assembling This Product
• Inspect all parts to make sure that nothing is broken or missing. If something is broken
or missing, please contact our service department at [e-mail].
• The rocker must be completely assembled before attempting to use it. Failure to do so
could result in damage to the chair or the user.
• Use proper safety gear and follow appropriate safety precautions when assembling this product.
• Important - Do not overtighten the screws.
• Only hand tools should be used for assembly. Do not use power tools.
• ECCB Outdoor will not be liable for any injury or damage resulting
from improper assembly and/or use of this product.
• Failure to follow all instructions will result in the product warranty being voided.
Assembly Instructions
Rockers
ECCB
OUTDOOR
V2
Congratulations on the purchase of your new poly
lumber rocker. These easy step-by-step instructions can
be used for assembling any of the following rockers.
Adirondack Rocker
(This style is used for instructions)
Harbor Rocker Lake Shore Rocker

Parts
Hardware - Shown at Actual Size
Tools - Not Included
Make sure you have received everything. If anything is missing or damaged, please contact our service department at
[e-mail].
Please note that for shipping purposes, the hardware will already be loosely attached in the appropriate holes.
Back - 1 pc Seat - 1 pc Arms - 2 pcs
1 Right
1 Left
Top view of arms Side view of arms
Bolts - 16 pcs Washers - 32 pcs Nut - 16 pcs
A B C
Brace - 1 pc
E
Rocker Bottoms - 2 pcs
These are interchangeable
D
F G H
716 in. (11mm) socket & ratchet
716 in. (11mm) open ended wrench
Important: When attaching the nuts, ALWAYS start with the metal part screwing onto
the bolt/screw. Starting with the plastic part will not work and may cause the chair not
to be properly assembled. See illustration to the right. Plastic Insert
966 Perry Highway, Mercer, PA 16137 • Phone [phone]
ECCBOutdoor.com

Let’s Get Started!
Step 1 - Attach the Seat to the Arms
• Line up the top holes in the arms (C) to the holes on the side of the seat (B)
• Attach the arms (C) to the seat (B) using the hardware shown below
* You will rst have to remove the hardware from those holes
G FGH
C
C
B
Step 2 - Attach the Back to the Seat and Arms
• Lay the seat and arms front side down (see graphic below), and line up the holes in the bottom of the back
(A) to the holes in the rear of the seat (B)
* You will rst have to remove the hardware from those holes
• The weight of the back will now cause the seat to rock forward slightly, where you can now attach the back
to the arms
Lay the seat on its side
when attaching the arms
Tip
G FGH G FGH
A
A
966 Perry Highway, Mercer, PA 16137 • Phone [phone]
ECCBOutdoor.com

Step 3 - Attach the Rocker Bottoms
• Position the rocker bottoms (D) to the outside of the arms (C). Make sure the short end of the rocker
bottoms are facing front
• Attach the rocker bottoms using the hardware shown below
* You will rst have to remove the hardware from those holes
• Place the brace (E) between the arms and attach it with the hardware shown below
* You will rst have to remove the hardware from those holes
Step 4 - Attach the Bottom Brace
Care
G FGH
G FGH
Poly lumber is easy to clean and maintain. Dust with a soft cloth or soft bristle brush, and tend to spills and
stains with a mild soap and water. No waterproong, no staining, and no painting is ever required!
IMPORTANT! Periodically check to make sure that all screws are properly tightened.
That’s all there is to it and now you have a comfortable rocker that we hope you will enjoy.
Thank you for your business!