Echo HCA-265 User manual

WARNING
Readrulesforsafeoperationandinstructionscarefully.ECHOprovidesanOperator's
ManualandaSafetyManual.Bothmustbereadandunderstoodforproperandsafeopera-
tion.Failuretodosocouldresultinserousinjury.
Shaft Hedge Clipper
Operator'sManual
MODEL HCA-265
X750010183
12/07
X7502024603

2
Copyright©2008ByEcho,Incorporated
All Rights Reserved.
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job
dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will
find both easy to use and full of helpful operating tips and SAFETY messages.
Maintenance ................................................................... 17
- SkillLevel................................................................. 17
- Maintenance Intervals ............................................. 17
- AirFilter ................................................................... 18
- FuelFilter ................................................................. 18
- SparkPlug ................................................................ 19
- CoolingSystem........................................................ 19
- ExhaustSystem........................................................ 20
- Carburetor Adjustment ............................................ 21
- Lubrication............................................................... 22
- Sharpening Blades ................................................... 24
- Blade Adjustment .................................................... 24
Troubleshooting ............................................................. 25
Storage............................................................................ 26
Specifications.................................................................. 27
ServicingInformation...................................................... 28
- Parts/SerialNumber ................................................. 28
- Service ..................................................................... 28
- ECHOConsumerProductSupport........................... 28
- Warranty Card ......................................................... 28
- Additional or Replacement Manuals ....................... 28
Specifications, descriptions and illustrative material in this
literature are as accurate as known at the time of publica-
tion, but are subject to change without notice. Illustrations
may include optional equipment and accessories, and may
not include all standard equipment.
THE OPERATOR'SMANUAL
Read and understand this manual before operation. Keep it in a safe
place for future reference. It contains specifications and information for
operation, starting, stopping, maintenance, storage and assembly
specific to this product.
THE SAFETY MANUAL
Read and understand this manual before operation. Keep it in a safe
place for future reference. It explains possible hazards involved with the
use of Hedge Clippers and what measures you should take to make their
use safer.
TABLE OF CONTENTS
Introduction ...................................................................... 2
- The Operator's Manual............................................... 2
- The Safety manual...................................................... 2
Safety ................................................................................ 3
- Manual Safety Symbols and Important Information .. 3
- InternationalSymbols ................................................ 3
- Personal Conditions and Safety Equipment .............. 4
- Equipment .................................................................. 6
EmissionsControl ............................................................. 6
Description ....................................................................... 7
Contents ........................................................................... 9
Assembly .......................................................................... 9
- Drive Shaft Assembly / Power Head.......................... 9
- Throttle Linkage and Ignition Leads........................ 10
- Balance and Adjust Unit.......................................... 11
Operation ........................................................................ 11
- Fuel .......................................................................... 11
- Adjusting Cutting Angle ......................................... 13
- Rotate Cutter Assembly .......................................... 14
- StartingColdEngine ................................................ 14
- StartingWarmEngine.............................................. 15
- Stopping Engine ...................................................... 16
- HedgeTrimming ...................................................... 16

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 3
INTERNATIONALSYMBOLS
Symbol
description/application Symbol form/shape Symbol
description/application
Symbol form/shape
Hot
Surface
Carburetor
adjustment
-Idlespeed
Carburetor
adjustment
- High speed
mixture
Symbol
description/application Symbol form/shape Symbol
description/application
Symbol form/shape
Readand
understand
Operator'sManual.
Weareyes,ears
andhead
protection
Emergencystop
Fueland oil
mixture
FingerSevering
Carburetor
adjustment
-Lowspeed
mixture
Safety/Alert
Do not operate
closerthan 15M
(50 ft.) from
electrical
hazards.
Keepbystanders
atleast15meters
(50feet)away.
Planretreatpath
from falling
objects.
Wear hand
protection.Use
twohanded.
DONOTsmoke
nearfuel.
DONOTallow
flamesorsparks
nearfuel.
Wear slip
resistantfoot
wear.
Ignition
ON/OFF
Primerbulb
Avoidallpower
lines.This unitis
notinsulated
againstelectrical
current.
Choke Control
"Cold Start"
Position
(ChokeClosed)
Choke Control
"Run"
Position
(ChokeOpen)
PERSONAL CONDITION AND SAFETY EQUIPMENT
WARNING
Hedge Clipper users risk injury to themselves and others if the hedge clipper is used improperly and or safety
precautions are not followed. Proper clothing and safety gear must be worn when operating a hedge clipper.
SAFETY
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages pre-
ceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to
WARNING
Thesafetyalertsymbolaccompaniedbytheword
“WARNING”callsattentiontoanactorcondition
whichCANleadtoseriouspersonalinjuryordeath
ifnotavoided.
CIRCLEANDSLASHSYMBOL
This symbol means the specific action
shown is prohibited. Ignoring these
prohibitions can result in serious or fatal
injury.
CAUTION
Thesafetyalertsymbolaccompaniedbytheword
“CAUTION”callsattentiontoanactorcondition
whichmayleadtominorormoderatepersonalinjury
ifnotavoided.
NOTE
This enclosed message provides tips for use, care
and maintenance of the unit.
IMPORTANT
The enclosed message provides information
necessary for the protection of the unit.
DANGER
Thesafetyalertsymbolaccompaniedbytheword
“DANGER”callsattentiontoanactorcondition
whichWILLleadtoseriouspersonalinjuryordeath
ifnotavoided.

4
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• ifyouaretakingmedication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Eye protection that meets ANSI Z87.1 or CE requirements must be worn whenever you operate the unit.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your grip on the handles. Gloves also reduce the transmission of
machine vibration to your hands.
Hearing Protection
Wear hearing protection. ECHO recommends wearing hearing protection whenever unit is used.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DONOTWEARSHORTS,
• DONOTWEARTIES,SCARFS,JEWELRY.
Wear protective hair covering to contain long hair.
Wear sturdy work shoes with nonskid soles;
• DONOTWEAROPENTOEDSHOES,
• DONOTOPERATEUNITBAREFOOTED.
Wear no-slip, heavy duty work gloves.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue which may lead to heat stroke. Schedule heavy work for early
morning or late afternoon hours when temperatures are cooler.
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals, may be
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensa-
tions, followed by loss of color and numbness in the fingers. The following precautions are strongly recommended,
becausetheminimumexposurewhichmight trigger the ailment is unknown.
• Keep your body warm, especially the head, neck, feet, ankles, hands,
and wrists.
• Maintain good blood circulation by performing vigorous armexercises
during frequent work breaks, and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the unit or other hand-held power equipment is not
required.
• If you experience discomfort, redness, and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 5
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness,
swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high
riskfordevelopingaRepetitive StressInjury(RSI).Anextreme RSIconditionisCarpalTunnel Syndrome(CTS),which
could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged
exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended, or twisted position.
Instead try to maintain a straight wrist position. Also, when grasping,
use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive move-
ment.
• Do exercises to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if
you feel tingling, numbness, or pain in the fingers, hands, wrists, or
arms. The sooner RSI/CTS is diagnosed, the more likely permanent
nerve and muscle damage can be prevented.
DANGER
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can cause
serious injury or death.
ReadtheManuals
• Provide all users of this equipment with the Operator's Manual and
Safety Manual for instructions on Safe Operation.
CleartheWorkArea
• Spectators and fellow workers must be warned, and children and
animalspreventedfrom comingnearerthan15 m(50ft.) whiletheunit
is in use.
KeepaFirmGrip
• Hold the front and rear handles with both hands, with thumbs and
fingers tightly encircling the handles.
KeepaSolidStance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not over reach.
CuttingAngleAdjustments
• Only adjust cutting blade angle with unit flat on the ground, with the
engine stop switch in the “STOP” position. Never adjust cutting
angle with unit standing upright.
AvoidContactWithGearBoxAssemblyDuringUse
• Gear box assembly becomes hot during use. Avoid contact with gear
box assembly when using unit or making cutting angle adjustments.
AvoidHotSurfaces
• Keep exhaust area clear of flammable debris. Avoid contact during
andimmediatelyafteroperation.

6
EmissionControlLabel (locatedonEngine) (EXAMPLEONLY,informationonlabelvariesbyFAMILY).
PRODUCT EMISSION DURABILITY
The 300 hour emission durability compliance period is the time span selected by the manufacturer certifying the
engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are
followed as listed in the Maintenance Section of this manual.
EQUIPMENT
WARNING
Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment
combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments, or accessories which
have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and
safety manual.
• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.
• Inspect fuel lines, tank and area around carburetor for fuel leaks. DO NOT operate unit if leaks are found.
• Never adjust blades when the engine is operating.
• Inspect hand guard for damage. Replace if damaged or missing.
• Check that the blade assembly is firmly attached and in safe operating condition. Dull, loose or damaged blades should
not be used.
EMISSION CONTROL
EPA Phase 2 / C.A.R.B. TIER III
The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank
theControlSystem isEVAP(Evaporative Emissions).Evaporativeemission maybeapplicable toCaliforniamodelsonly.
IMPORTANTENGINEINFORMATION
ENGINEFAMILY: 8EHXS.0254KG DISPLACEMENT: 25.4CC
EMISSIONCOMPLIANCEPERIOD :300HRS.
THISENGINEMEETS U.S. EPA PH2 EXH AND2007AND
LATERCALIFORNIAEXH AND EVAPEMISSIONREGULA-
TIONS FOR S.O.R.E. REFER TO OWNER'S MANUAL FOR
MAINTENANCESPECIFICATIONSANDADJUSTMENTS.
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings.
•ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop
before removing obstructions, clearing debris, or servicing unit.
•DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.
•NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 7
1
2
3
4
5
DESCRIPTION
Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the
instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDER-
INGinstructionsforspecificinformation.
P/N 89016006361
Hot Decal (near muffler)
18
19
14
22
15
16
17
20
21
P/N 89022809560
Shaft Decal
Spanish Decal
English Translation
23
13
P/N 89016012360
P/N X505001930
12
611
9
7
P/N 89017854331
8
10

8
1. POWERHEAD-FactoryAssembled. Includes theEngine,Clutch, FuelSystem, IgnitionSystemand RecoilStarter.
2. GRIP,RIGHTHAND,REAR-CushionedgripforRightHand.
3. THROTTLETRIGGERLOCKOUT-Thislevermustbeheldduringstarting.Operationofthethrottletriggeris
prevented unless throttle trigger lockout lever is engaged.
4. STOP SWITCH - Controls engine ignition. Move switch forward to start and run engine, back to “STOP” position
to stop engine.
5. HANDGUARD/BLADELOCK- Locks bladeinplace fortravel/ storage. Always assurebladecover isinstalled
whenlockingblade.
6. BLADEINDEXINGRING-Pullringoutandturn1/4turntolockoutpositionwhenadjustingbladeangle.
7. BLADES - Double reciprocating blades mounted to a blade support bar. Double-sided blades are capable of cutting
on either side of the blade.
8. GEARHOUSINGASSEMBLY-Gearhousingcontainsdrivegearsfortransmittingpowertocuttingblades. Pivot-
ing design permits blades to articulate 180 degrees in 15-degree increments.
9. BLADEADJUSTMENTHANDLE-Providessecurehandgripforadjustingcuttingbladeangle.
10. FRONTDRIVESHAFTGRIP-Cushionedhandgripforgrippingdriveshaftassembly.
11. DRIVESHAFTASSEMBLY-Includestheflex driveshaft,rear handleassembly,harnessring, cushionedfrontshaft
grip, and safety decals.
12. THROTTLETRIGGER-Controlsenginespeed. Springloadedtoreturntoidlewhenreleased.Duringacceleration,
depress gradually for best operating technique.
13. BLADE COVER - Used to cover blade during transport and storage. Remove blade cover before using unit.
14. SPARKARRESTOR-CATALYTICMUFFLER/MUFFLER-Themufflerorcatalyticmufflercontrolsexhaustnoise
and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep
exhaustareaclearofflammabledebris.
15. FUELTANK-Containsfuelandfuelfilter.
16. RECOILSTARTERHANDLE-Pullhandleslowlyuntilstarterengages,thenquicklyandfirmly. DONOTpullrope
all the way out or allow the handle to snap back, damage to the starter will occur.
17. FUELTANKCAP-Coversandsealsfueltankopening.
18. PURGEBULB- Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from the
carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump purge bulb
an additional 4 or 5 times.
19. AIRCLEANER-Containsreplaceablefilterelement.
20. CHOKECONTROL- Located on the top of the air cleaner housing. Move the lever to "COLD START" ( )to
close the choke for Cold Starting. Move lever to "RUN" ( ) position after engine fires.
21. SPARKPLUG- Providessparktoignitefuelmixture.
22. TOPGUARD-Protectsarmfromthehotengine.
23. SHOULDER HARNESS - An adjustable strap that suspends the unit from the operator.

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 9
___ 1 - PowerHead
___ 1 - DriveShaft/GearCaseAssembly
___ 1 - Operators Manual
___ 1 - Hedge ClipperSafetyManual
___ 1 - Warranty Statement
___ 1 - Warranty Registration Card
___ 1 - Safety Glasses
___ 1 - Shoulder Harness
___ 1 - BladeCover
___ 1 - EchoPowerBlend XTM 2-strokeoilsample
___ 1 - T-Wrench
___ 1 - 4mmHexWrench
___ 1 - 8mm/10mmWrench
ASSEMBLY
Tools Required: 4mmhexwrench,8mmx10mmOpenEndWrench,
Screwdriver
Parts Required: Power Head, Drive Shaft/Gear Case Assembly
DRIVE SHAFT/POWER HEAD
1. Stand power head upright on a level surface.
2. Loosen the two (2) drive shaft clamp bolts (B) at engine drive shaft
clamp, and remove center drive shaft location bolt (A).
3. Carefully fit driveshaft assembly to engine making sure that
inner drive shaft engages clutch mount.
4. Turn drive shaft housing until locating hole lines up with location
hole in clamp and install center drive shaft location bolt (A).
A
BB
CONTENTS
Due to packaging restrictions, some assembly is required.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.

10
5. Tighten two (2) drive shaft clamp bolts (B) securely.
6. Route throttle linkage and ignition lead assembly along shaft and
clip as shown.
B
B
THROTTLE LINKAGE AND IGNITION LEADS
1. Close choke and removeairfiltercover.
2. Place throttlelinkage(C)through adjustment fixture(D)andinstall
wire end into large carburetor throttle swivel hole (E). Check throttle
for freedom of movement and that wide open throttle / low idle
extremes are adjusted properly. The throttle linkage must be
adjusted by moving the adjustment fixture (D). Consult with your
Echo Dealer for correct adjustment procedure.
3. Connect 2 ignition stop leads (F, G) from throttle cable tubing to 2
ignition leads (F, G) on engine.
4. Secure ignition leads against engine housing with clip (H).
5. Install airfilterand cover.
C
D
F
GH
E
A
H
NOTE
Gear Housing must be aligned properly with engine. Aligning
center locating hole in driveshaft housing with center drive shaft
bolt (A) provides correct alignment.

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 11
OPERATION
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete
stop before removing obstructions, clearing debris, or servicing unit.
NOTICE:Use ofunmixed,improperlymixed,orfuelolderthan90days,(stalefuel),maycausehardstarting,poor
performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage
section of this manual.
FUEL
WARNING
Alternativefuels,suchas E-20 (20%ethanol),E-85 (85% ethanol) oranyfuels not meetingECHOrequirementsare
NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance problems,
loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper
clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carburetors and
other engine components.
Fuel Requirements
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to
10%Ethanol (grainalcohol)or15%MTBE(methyltertiary-butylether).Gasolinecontainingmethanol (woodalcohol) is
NOTapproved.
BALANCE AND ADJUST UNIT
1. Loosen harness clamp screw.
2. Put on harness and attach unit to harness.
3. Slide harness clamp up or down for comfortable operation
4. Tighten harness clamp screw.

12
oitaR1:05-xiMliOotleuF
.S.UCIRTEM
SAGLIOSAGLIO
snollaG.zo.lFretiL.cc
1
2
5
6.2 2.531 4
8
02
08 061 004
After use
• DO NOT store a unit with fuel in its tank.
Leaks can occur. Return unused fuel to an
approved fuel storage container.
Storage - Fuel storage laws vary by locality.
Contact your local government for the laws
affecting your area. As a precaution, store
fuel in an approved, airtight container. Store
in a well-ventilated, unoccupied building,
away from sparks and flames.
IMPORTANT
Storedfuelages. Do notmixmore fuel
than you expect to use in thirty (30)
days, ninety (90) days when a fuel
stabilizerisadded.
IMPORTANT
Stored two-stroke fuel may separate.
ALWAYS shake fuel container thor-
oughly before each use.
IMPORTANT
EchopremiumPowerBlendXTM Universal2-StrokeOilmaybemixed
at 50:1 ratio for application in all Echo engines sold in the past
regardless of ratio specified in those manuals.
Handling Fuel
DANGER
FuelisVERYflammable.Useextremecarewhenmixing,storingor
handling or serious personal injury may result.
• Use an approved fuel container.
• DONOTsmokenearfuel.
• DONOTallow flamesorsparksnearfuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps
slowly allowing pressure to equalize.
• NEVERrefuelaunitwhentheengineisHOTorRUNNING!
• DONOTfillfueltanks indoors. ALWAYS fill fueltanksoutdoors
over bare ground.
•DONOToverfillfueltank. Wipeupspillsimmediately.
• Securely tighten fuel tank cap and close fuel container after
refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or
operate unit until leakage is repaired.
• Move at least 3m (10 ft.) from refueling location before starting
the engine.
Mixing Instructions
1. Fill an approved fuel container with half of the required amount of
gasoline.
2. Add the proper amount of 2-stroke oil to gasoline.
3. Close container and shake to mix oil with gasoline.
4. Addremaininggasoline, closefuelcontainer,and remix.
IMPORTANT
Spilled fuel is a leading cause of hydrocarbon emissions. Some
states may require the use of automatic fuel shut-off containers to
reducefuelspillage.
TwoStrokeOil-Atwo-strokeengineoilmeetingISO-L-EGD(ISO/CD13738)andJ.A.S.O.FC/FDStandardsmustbe
used. Echo brand premium Power Blend X TM Universal 2-Stroke Oil meets these standards. Engine problems due to
inadequatelubricationcausedbyfailuretouse anISO-L-EGD(ISO/CD13738)andJ.A.S.O.FC/FDcertifiedoil,suchas
EchopremiumPowerBlendXTM, will void the two-stroke engine warranty. (Emission related parts onlyarecovered for
two years, regardless of two-stroke oil used, per the statement listed in the Emission Defect Warranty Explanation.)

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 13
ADJUSTING CUTTING ANGLE
WARNING
Never adjust cutting assembly with engine running.
WARNING
Hedge clipper blades are sharp. Always wear gloves when
adjusting cutting assembly.
WARNING
DO NOT stand hedge clipper on end when adjusting cutting angle,
otherwise serious injury may result
1. Place unit on a flat clear area. Assure stop switch is in the “STOP”
position.
2. Pull out indexing ring (A), and turn ¼ turn to lockout position.
3. Turn hedge clipper ¼ turn so that indexing ring faces downward.
4. Release hand-guard blade lock (B) with right hand, while holding
blade-adjustment handle (C) with left hand.
5. Rotate blades to desired cutting position.
6. Turn indexing ring ¼ turn to lock blade in place.
WARNING
Gear case assembly becomes HOT during use. Always grip
assembly at blade-adjustment handle when making cutting angle
adjustments, otherwise serious injury may result.
A
B
C
B

14
ROTATE CUTTER ASSEMBLY
Always use the unit from the right-hand side of your body – NEVER
from the left side. Rotate cutter assembly 180 degrees on driveshaft in
order to avoid cutting directly above your head, and to avoid contact
withhotmuffler.
1. Loosen gearcase clamping screw (A), hand guard clamping screw
(B),andremovegearcaselocating screw (C).
2. Rotate cutter assembly 180-degrees on driveshaft until locating
hole in driveshaft is visible through locating hole in gearcase.
3. Install gearcase locating screw (C), and securely tighten all
hardware.
WARNING
Hedge Clipper blades are very sharp. Wear gloves to protect hands
when rotating cutter assembly or serious personal injury may
result.
WARNING
During operation, the complete unit, especially the drive shaft
housing and gearcase may become too hot to touch. Avoid contact
when rotating cutter assembly.
STARTING COLD ENGINE
NOTE
The blade cover is used for transportation and storage. Remove
blade cover before using the unit.
WARNING
The attachment will operate immediately when the engine starts and
could result in loss of control and possible serious injury. Keep
movable parts of the attachment off the ground and away from
objects that could become entangled or thrown.
1. Stop Switch
Move stop switch button (A) forward away from the STOP
position.
2. Close Choke
Move choke lever (B) to Cold Start ( ) Position.
A
BC
C
D
A
B

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 15
3. Purge Bulb
Pump purge bulb (C) until fuel is visible and flows freely in the clear
fuel tank return line. Pump bulb an additional 4 or 5 times.
4. Recoil Starter
Lay the unit on a flat area and keep movable attachment parts clear
of all obstacles. Firmly grasp right hand grip and throttle trigger
lockout with left hand and fully depress throttle trigger to wide
open position. Rapidly pull recoil starter handle/rope (D) until
enginefires(ormaximumfive[5]pulls).
5. Choke
After engine fires (or five [5] pulls), move choke lever back to
“Run” ( ) position. Hold throttle trigger and throttle trigger
lockout fully depressed and pull recoil starter handle/rope until
engine starts and runs. Release throttle trigger and allow unit to
warm up at idle for several minutes.
NOTE
If engine does not start with choke in Run position after 5 pulls,
repeat instructions 2 - 5.
6. Throttle Trigger
After engine warm up, gradually depress throttle trigger to increase
engine RPM to operating speed.
STARTING WARM ENGINE
The starting procedure is the same as Cold Start except DO NOT close
the choke, and do not depress throttle trigger to wide open position.
WARNING
The attachment should not move at idle, otherwise serious
personal injury may result.
NOTE
If attachment moves, readjust carburetor according to “Carburetor
Adjustment” instructions in this manual or see your ECHO Dealer.
1. Stop Switch
Move stop switch button (A) away from the STOP position.
2. Purge Bulb
Pump purge bulb (C) until fuel is visible and flows freely in the
“Clear”fuelreturnline.Pump bulb an addition 4 or5times.
3. Recoil Starter
Lay the unit on a flat area and keep movable attachment parts clear
of all obstacles. Rapidly pull recoil starter handle/rope (D) until
enginefires.
NOTE
If engine does not start after 5 pulls, use Cold Start Procedure.
C
D
B
D
C
D
A
D

16
STOPPING ENGINE
1. Throttle
Release throttle and allow engine to return to idle before shutting off
engine.
2. Stop Switch
Move stop switch button (A) to STOP position.
WARNING
If engine does not stop when stop switch is moved to STOP
position, close choke - COLD START position - to stall engine.
Have your ECHO dealer repair stop switch before using shaft
hedge clipper again.
IMPORTANT
Always install blade cover, and return cutting assembly to folded/
locked position for travel/storage.
HEDGETRIMMING
1. Holdtrimmerfirmlyandsqueezethrottletrigger toaccelerate
engine.
2. Tilt trimmer so cutting teeth are angled slightly toward the hedge or
shrub and proceed to cut.
WARNING
Never remove hands from unit when blades are moving.
WARNING
The engine continues running even when the blades have stopped
due to an obstruction. If this occurs, stop the engine, disconnect
ignition cable and remove the obstruction.
A

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 17
MAINTENANCE
Your ECHO product is designed to provide many hours of trouble free service. Regular scheduled maintenance will help
achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an
ECHOServiceDealerformaintenance. TohelpyoudecidewhetheryouwanttoDO-IT-YOURSELForhavetheECHO
Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO Dealer for repairs.
SKILL LEVEL
Level1= Easy to do. Most required tools come with unit.
Level2= Moderate difficulty. Some specialized toolsmayberequired.
Level3= Experiencerequired.Specializedtoolsarerequired.ECHOrecommends
that the unit be returned to your ECHO dealer for service
ECHOoffersREPOWERTM Maintenance KitsandPartsto makeyourmaintenance job easier.
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete
stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service.
Wear gloves to protect hands from sharp edges and hot surfaces.
MAINTENANCEINTERVALS
/TNENOPMOC METSYS ECNANETNIAM ERUDECORP
D'QER LLIKS LEVEL ROYLIAD EROFEB ESU
YREVE LEUFER
3SHTNOM 09RO SRUOH 6SHTNOM 072RO SRUOH
YLRAEY 006 SRUOH
serudecorPecnanetniaMrelaeDohcEdednemmoceR
troPtsuahxErednilyCnobraceD/naelC/tcepsnI 3C/I
sedalBneprahSnae
lC/tcepsnI 3)3(I
serudecorPecnanetniaMflesruoY-tI-oD
retliFriAecalpeR/naelC/tcepsnI 1C/I*R
ekohCnaelC/tcepsnI 2C/I
retliFleuFecalpeR/tcepsnI 1I*R
skael,metsySleuFecalpeR/tcepsnI 1*)4(I)4(I
metsySgnilooCnaelC/tcepsnI 2C/I
ro
tserrAkrapSrelffuMecalpeR/tcepsnI 2*I
xelF(tfahSevirD )sledoMelbaC esaerG 2)1(I
gnisuoHraeGesaerG 2)2(I
sedalBna
elC/tcepsnI 1)3(C/I
epoRretratSlioceRnaelC/tcepsnI 1*C/I
gulPkrapSnaelC/tcepsnI 2C/I*R
stloB/stuN/swercSecalpeR
/nethgiT/tcepsnI 1*R/I
SEDOCRETTELERUDECORPECNANETNIAM NAELC=C,ECALPER=R,TCEPSNI=I:
-ETONTNATROPMI deriuqerfoycneuqerfehtenimretedlliwecneirepxeruoydnaesulaut
cA.mumixameranwohsslavretniemiT
.ecnanetniam :SETONERUDECORPECNANETNIAM)1( OHCEylppA
®
EBUL
MT
.sruoh52yreve
)2( OHCEylppA
®
EBUL
MT
sruoh52-51yreve
)3( .esugnirudyllacidoirepsedalbetacirbuL.dedeensaneprahsdnanaelcdnaedalbtcepsnI
)4( .yti
rgetninoissimeniatniamotecnanetniamralugereriuqerTONODsknatleufevitaropavewoL
*..noitcepsnignirudraewr
oegamadfognidnifehtnodesaberaecalperotsnoitadnemmocerllA

18
AIR FILTER
Level1.
Tools required: 25or50mm(1or2in.)Cleaningbrush
Parts required: Air Filter
1. Close choke (Cold Start Position [ ). This prevents dirt from
entering the carburetor throat when the air filter is removed. Brush
accumulateddirtfromaircleanerarea.
2. Removeairfiltercover.Brushdirtfrominsidecover.
3. Removeairfilterandlightlybrushdebrisfromfilter.Replacefilterif
it is damaged, fuel soaked, very dirty, or the rubber sealing edges
aredeformed.
4. If filter can be reused, be certain it:
• Fits tightly in the air filter cavity.
• Is installed with the original side out.
5. Installairfiltercover.
FUEL FILTER
Level1.
Tools required: 200-250mm(8-10in.)lengthofwirewithoneendbent
into a hook, clean rag, funnel, and an approved fuel
container.
Parts required: FuelFilter
DANGER
FuelisVERYflammable.Useextremecarewhenmixing,storingor
handling.
1. Use a clean rag to remove loose dirt from around fuel cap and
emptyfueltank.
2. Use the “fuel line hook” to pull the fuel line and filter from the
tank.
3. Remove thefilterfromthe lineandinstallthe new filter.

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 19
SPARK PLUG
Level2.
Tools Required: T-Wrench, feeler gauge, soft metal brush
Parts Required: SparkPlug NGKBPM-8Y
IMPORTANT
UseonlyNGKBPM-8Ysparkplug(BPMR-8YinCanada)otherwise
severe engine damage may occur.
1. Remove spark plug and check for fouling, worn and rounded
center electrode.
2. Clean the plug or replace with a new one. DO NOT sand blast to
clean.Remainingsandwilldamageengine.
3. Adjust spark plug gap by bending outer electrode.
4. Tightensparkplugto150-170kg/cm(130-150in.lb.).
COOLING SYSTEM
Level2.
Tools required: CrossHeadScrewdriver,3&4mmHexWrench,
Cleaning Brush,25-50mm(1-2in.)
Parts Required: None if you are careful.
IMPORTANT
To maintain proper engine operating temperatures, cooling air
must pass freely through the cylinder fin area. This flow of air
carries combustion heat away from the engine.
Overheating and engine seizure can occur when:
• Air intakes are blocked, preventing cooling air from reaching the
cylinder.
• Dust and grass build up on the outside of the cylinder. This build up
insulates the engine and prevents the heat from leaving.
Removal of cooling passage blockages or cleaning of cooling fins is
considered “Normal Maintenance.” Any failure attributed to lack of
maintenance is not warranted.
1. Remove spark plug lead.
2. Removeaircleanercover.
3. Removemufflercoverscrewandmufflercover(A).
4. Remove 2 engine cover screws and engine cover (B).
0.65 mm
(0.026 in.)
A
B

20
IMPORTANT
DO NOT use a metal scraper to remove dirt from the cylinder fins.
5. Use brush to remove dirt from the cylinder fins.
6. Remove grass and leaves from the grid between the recoil starter
and fuel tank.
7. Assemble components in reverse order.
EXHAUST SYSTEM
Spark Arrestor Screen
Level2.
Tools Required: CrossHeadScrewdriver, 4mmHexWrench,Soft
Metal Brush
Parts Required: SparkArrestor Screen,Gasket
1. Remove spark plug lead.
2. Removemufflercoverscrewandmufflercover(A).
3. Place piston at Top Dead Center (TDC) to prevent carbon/dirt from
enteringcylinder.
4. Remove spark arrestor screen (B), gasket (C), and exhaust guide (D)
frommufflerbody.
5. Clean carbon deposits from muffler components.
NOTE
When cleaning carbon deposit, be careful not to damage the
catalyticelementinsidemuffler.
6. Replace screen if it is cracked, plugged or has holes burned
through.
7. Assemble components in reverse order.
Cylinder Exhaust Port
Level3.
IMPORTANT
The cylinder exhaust port must be inspected and cleaned of excess
carbon every 3 months or 90 hours of operation in order to maintain
this engine within the emissions durability period. ECHO strongly
recommends that you return your unit to your ECHO dealer for this
importantmaintenanceservice.
B
C
D
A