EchoMaster Pro IntelliHaul User manual

Installation Guide
19367548
FC-GMOESWR-
BYOM-TC
IntelliHaul
Integrated Towing Assistance Package
IOB 7” Radio Wireless Camera Kit

3
email - [e-mail] (US) - tel - 866-766-2267
2
email - [e-mail] (US) - tel - 866-766-2267
Illustrations are typical and may not match exact vehicle details.
Cover all surfaces with tape or plastic protection lm to protect against
scratching and damage. EchoMaster is in no way responsible for any damage
that may occur during installation.
This product has been validated in the vehicles listed on the application guide only.
Care must be taken when installing this accessory to ensure damage does not occur
to the vehicle. The installation of this accessory should follow approved guidelines to
ensure proper installation. Read entire instructions thoroughly before starting.
This document covers such items as:
- Vehicle Protection (use of covers and blankets, cleaning chemicals, etc).
- Vehicle Disassembly / Reassembly (panel removal, part storage, etc).
- Electrical Component Disassembly / Reassembly (battery disconnection,
connector removal, etc).
NOTES:
Removed Parts: Inspect the vehicle and parts for any damage.
Place all removed parts on a protected surface in an area where they will not get
damaged.
Connectors: When disconnecting connectors, do not pull on the wires; pull by
holding the connectors.
Retain the factory reverse camera if equipped.
Prior to Installation
19367548
Integrated Towing Assistance Package
Installation Guide

3
email - [e-mail] (US) - tel - 866-766-2267
Illustrations are typical and may not match exact vehicle details.
2
email - [e-mail] (US) - tel - 866-766-2267
Illustrations are typical and may not match exact vehicle details.
CAUTION
Consult your vehicle owner’s manual to disconnect the battery. Do not disconnect
ANY airbag connectors or indicators. Doing so may result in activating a diagnostic
code. These codes will require the dealer to perform the reset procedure which may
incur a reset fee. If you are unsure of any vehicle trim removal process consult the
OEM service manual.
Removing vehicle trim panels in extreme hot and/or cold climate could result in
damage. Use care when removing all vehicle trims.
Using painter’s blue tape on the vehicle trim panels can help limit any scratches
and/or marring. Use a nylon trim panel removal tool whenever possible.
Vehicle Preparation & Protection
Recommended Tools
Painter’s tape
19367548
Integrated Towing Assistance Package
Installation Guide

5
email - [e-mail] (US) - tel - 866-766-2267
4
email - [e-mail] (US) - tel - 866-766-2267
Illustrations are typical and may not match exact vehicle details.
Removing the Radio (IOB 7” screen)
Step 1
Using a nylon trim removal tool, remove the
LCD display trim panel.
Step 2
Remove the 4 x 7mm bolts from around the
LCD display.
Once screws have been removed, remove
the unit from the dash.
Step 3
Disconnect the 4 connectors from the back
of the LCD display assembly and set aside.
19367548
Integrated Towing Assistance Package
Installation Guide

7
email - [e-mail] (US) - tel - 866-766-2267
5
email - [e-mail] (US) - tel - 866-766-2267
Illustrations are typical and may not match exact vehicle details
Removing the Door Sill(s)
Step 1
Remove passenger front and rear door sill
plastics.
Set aside.
Route Camera Extension Harness
Route 16-pin main camera extension
cable down below the dash.
This should pass through hole
located in the back portion of the
radio cavity and exit from bottom
of dash.
For vehicles with a center council,
route the camera harness towards
the glove box cavity.
Camera 1 = Not used
Camera 2 = Not used
Camera 3 = Wireless Camera.
Camera 4 = Not used (aftermarket
reverse camera input)
19367548
Integrated Towing Assistance Package
Installation Guide

Installation Guide
6
email - [e-mail] (US) - tel - 866-766-2267
Illustrations are typical and may not match exact vehicle details
email - [e-mail] (US) - tel - 866-766-2267
Route Camera Extension Harness (Rear)
Route extension harness(s) to the rear of the vehicle (passenger side only).
Remove 1 x 7mm bolt from C-pillar panel and remove panel. Route wire to bottom
corner of rear window and secure with zip ties.
19367548
Integrated Towing Assistance Package

9
email - [e-mail] (US) - tel - 866-766-2267
7
email - [e-mail] (US) - tel - 866-766-2267
Illustrations are typical and may not match exact vehicle details
Installing Wireless Receiver
Plug in wireless receiver module. Use
double sided adhesive tape to mount to
the glass
Mount Module to Bracket
Mount module to bracket using the four
provided M3 screws.
Be sure to orient the plug correctly
otherwise damage will occur.
Use two sided tape to fasten to
rear window.
WARNING
19367548
Integrated Towing Assistance Package
Installation Guide

8
email - [e-mail] (US) - tel - 866-766-2267
Illustrations are typical and may not match exact vehicle details.
8
email - [e-mail] (US) - tel - 866-766-2267
Illustrations are typical and may not match exact vehicle details.
Mounting the Module
Module Connections
Connect 8-pin power t-harness, the 16-pin
main camera extension cable, the 4-pin
VBM t-harness (2018-19), and the LVDS
teal colored connector to the module.
Fasten harnesses to the bracket using zip
ties through the holes provided.
Select vehicle year using dip switches.
u 2018-2019 dip switch 1 down
2 up
3 down
4 up
u 2017 dip switch 1 up
2 down
3 down
4 up
u 2015-2016 dip switch 1 up
2 up
3 down
4 up
Requires t-harness for VBM.
PLEASE NOTE 2018-19 only
2018-19 (only)
t-harness
for VBM
CAUTION
Set Vehicle
Year
Place into radio cavity and secure module/bracket
assembly into place using 2 x 7mm bolts.
(2 x 7mm bolts not provided)
19367548
Integrated Towing Assistance Package
Installation Guide
Note: To enable full camera mode set dip
3 up. Leave down if only installing one
camera (CAMERA 3 Input).

11
email - [e-mail] (US) - tel - 866-766-2267
9
email - [e-mail] (US) - tel - 866-766-2267
Illustrations are typical and may not match exact vehicle details.
LVDS Connection
Re-install
Connect the 20-pin t-harness to the radio display and the
radio display harness.
Secure loose wiring with zip ties.
Disconnect the Grey and Gold connector from the
radio module along with the black LVDS connector
with the Blue cable.
Connect the Grey and Gold connector
t-harness to the radio module and the radio harness.
Connect the loose male LVDS connector into
female EchoMaster connector. Connect the male
EchoMaster LVDS connector into the radio module.
Reinstall all removed panels and test system.
PLEASE NOTE
2018-19 Vehicles only require t-harness for VBM
19367548
Integrated Towing Assistance Package
Installation Guide

10
Operation/Installation Guide
email - [e-mail] (US) - tel - 866-766-2267
Illustrations are typical and may not match exact vehicle details
email - [e-mail] (US) - tel - 866-766-2267
Accessing Camera and Installation settings
Press and hold the “HOME” button for more than 2 seconds to enter the TC camera view
(input 3).
Camera 4 input is automatically activated when vehicle is in reverse gear when
aftermarket camera option is selected in the Installer Setup.
The camera view is accessible after 7 seconds while in reverse. Press and hold the
“HOME” button for more than 2 seconds to access camera view while in reverse.
Press and hold anywhere on the sceen while in Camera view to access Camera
Setup page shown below. From Camera setup menu you can enable / disable
functions. FIG 1.
1. Enable Front Camera Speedup Trigger - When enabled, will trigger front camera when
entering drive from reverse gear. Turns off above 8 mph.(Only avaliable in full mode)
2.
3. Enable Turn Signal Cameras - When enabled, blind spot cameras will activate and
display on the screen when the turn signals are activated. (Only avaliable in full mode)
4. Enable Dynamic Backup Curves - When enabled, the module will overlay
dynamic backup guide lines over the reverse image aftermarket cameras
only. (Only avaliable in full mode)
Press and hold the small lock icon in the top right corner of the camera
setup menu to access Installer Setup. FIG 2.
1. Enable Aftermarket Backup Camera - can be enabled by pressing this tab.
2. Note: The other options are only avaliable in full mode.
FIG 1 FIG 2
Enable Front Camera Slowdown Trigger - When enabled, it will activate the front
camera when speed is reduced below 10 mph and steering wheel is turned more than
10 degrees. (This prevents unwanted front camera activation in stop and go traffic).
(Only avaliable in full mode)
19367548
Integrated Towing Assistance Package

11
email - [e-mail] (US) - tel - 866-766-2267
Illustrations are typical and may not match exact vehicle details.
10
email - [e-mail] (US) - tel - 866-766-2267
Illustrations are typical and may not match exact vehicle details.
Wiring Diagram
Part No Description Qty
1FC-GMS-BYOM2 Main Interface module 1
2 GMSWRBRKT-1 Main Interface bracket 1
3 BSM1-PTH Power T-harness 1
4 BSM1-CEH Camera extension harness 1
5 BSM-WCEH-D 3657mm/114” Camera extension harness 1
6 BSM1-TMON-HAR V2 250mm/10” T - harness for VBM (2018-19 only) 1
2018-19 only
6
Installation Guide
19367548
Integrated Towing Assistance Package

Clearwater Florida 33760
EchoMaster is a Power Brand of AAMP Global.
www.echomaster.com
email - [e-mail] - tel - 866-766-2267 (US)
AGREEMENT: End user agrees to use this product in compliance with the instructions and terms
of use above and with all State and Federal laws. EchoMaster provides instructions and safety
warnings with respect to this product and disclaims all liability for any use not in conformity with
those instructions or other misuse of its product. If you do not agree, please discontinue use
immediately and contact EchoMaster. This product is intended for off-road use and passenger
use only.
IG-FC-GMOESWR-BYOMTC
REV. 090418