Eclipse Security ECL-IPSP212 User manual

ECL-IPSP212 Manual
Version 1.0.0

i
Table of Contents
1INTELLIGENT SPEED DOME INSTALLATION..................................................1
1.1 Installation Environments .....................................................................................................................1
1.2 Check installation space and installation location intension ...........................................................1
1.3 About cable.............................................................................................................................................1
1.4 Please keep all package material well for future use.......................................................................1
2SETUP BEFORE INSTALLATION ......................................................................2
2.1 Check Accessories................................................................................................................................2
2.2 Open Device...........................................................................................................................................2
2.3 Initial Setup.............................................................................................................................................2
2.4 Dial Switch Setup (For Analog Speed Dome Only)..........................................................................3
2.4.1 Dial Switch Buttons...........................................................................................................................3
2.4.2 Baud Rate and Parity Setup............................................................................................................4
2.4.3 Address ..............................................................................................................................................5
2.4.4 Terminal Matching Resistance Setup ............................................................................................5
3CEILING MOUNT................................................................................................7
3.1 Installation Components .......................................................................................................................7
3.2 Ceiling Mount Installation Steps ..........................................................................................................7
3.2.1 Installation Environments.................................................................................................................7
3.2.2 Installation Steps...............................................................................................................................7
3.2.3 Cable Connection .............................................................................................................................9

ii
4WALL MOUNT BRACKET INSTALLATION......................................................10
4.1 Component Installation .......................................................................................................................10
4.2 Wall Mount Installation Steps ............................................................................................................10
4.2.1 Installation Environments...............................................................................................................10
4.2.2 Installation Steps.............................................................................................................................10
5IN-CEILING MOUNT BRACKET INSTALLATION ............................................13
5.1 Component Installation .......................................................................................................................13
5.2 Installation.............................................................................................................................................13
5.2.1 Installation Requirements ..............................................................................................................13
5.2.2 Installation Steps.............................................................................................................................13
6APPENDIX Ⅰ THUNDER PROOF AND SURGE PROTECTION .......................16
7APPENDIX Ⅱ ABOUT RS485 BUS ...................................................................17
7.1 RS485 Bus Main Feature ...................................................................................................................17
7.2 RS485 Bus Transmission Distance ..................................................................................................17
7.3 The Problem in Practical Use ............................................................................................................17
7.4 RS485 Bus FAQ ..................................................................................................................................18
8APPENDIX Ⅲ THE 24V AC WIRE GAUGE AND TRANSMISSION DISTANCE
RELATIONSHIP SHEET ..........................................................................................19

iii
9APPENDIX Ⅳ12V AC WIRE GAUGE AND TRANSMISSION DISTANCE
RELATIONSHIP SHEET ..........................................................................................20
10 APPENDIX V WIRE GAUGE REFERENCE SHEET ........................................ 21

iv
Welcome
Thank you for purchasing our speed dome!
Please read the following safeguards and warnings carefully before you install or use the
product!

v
Important Safeguards and Warnings
Safety Measures
1. Qualified Engineer Needed
zThe installation engineer or maintenance engineer shall have corresponding CCTV system
installation certificate or maintenance qualification certificate.
zThe installation engineer or maintenance engineer shall have qualification certificate for work
at height.
zThe installation engineer or maintenance engineer shall have the basic knowledge and
operation technique for low-voltage cable layout and low-voltage electronic cable connection.
zPlease read the installation manual carefully and keep it well for future reference,
zWe are not liable for any problems caused by unauthorized modifications or attempted repair.
2. Lifting Appliance Requirement
zPlease select the proper speed dome installation mode and use the lifting appliances at the
safety environment.
zThe lifting appliances shall have the enough capacity to reach the installation height.
zThe lifting appliances shall have safe performance.
The precaution measures include two types: Warning and Note.
zWarning: It is to alert you there is an optional risk of death or series injury!
zNote: It is to alert you there is an optional risk of damage or property loss!
Warning
1. All installation and operation here should conform to your local electrical safety codes. We
assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
2. Be sure to use all the accessories (such as power adapter) recommended by manufacturer.
3. Do not connect several speed domes to one power adapter. It may result in overheat or fire
if it exceeds the rated load.
4. Before you connect the cable, install or uninstall, or begin the daily maintenance work,
please turn off the power and unplug the power cable.
5. Please make sure the produce is secure firmly on the wall or the ceiling.
6. Please turn off the power and unplug the power cable, If there is any smoke, disgusting
smell, or noise. Please contact your local retailer or customer service centre for help.

vi
7. All the examination and repair work should be done by the qualified service engineers. We
are not liable for any problems caused by unauthorized modifications or attempted repair.
Note
1. Safety Transportation
zHeavy stress, violent vibration or water splash are not allowed during transportation, storage
and installation.
zThis series product must use split type package during the transportation.
zWe are not liable for any damage or problem resulting from the integrated package during
the transportation.
2. When device is malfunction
Shut down the device and disconnect the power cable immediately if there is smoke, abnormal
smell or abnormal function. Please contact your local retailer ASAP.
3. Do not try to dismantle or modify the device
zThere is risk of personal injury or device damage resulting from opening the shell.
zPlease contact your local retailer if there is internal setup or maintenance requirement.
zWe are not liable for any problems caused by unauthorized modifications or attempted repair.
4. Do not allow other object falling into the device
zPlease make sure there is no metal or inflammable, explosive substance in the speed dome.
zThe above mentioned objects in the device may result in fire, short-circuit or damage.
zPlease shut down the device and disconnect the power cable if there is water or liquid falling
into the camera. Please contact your local retailer ASAP.
zPlease pay attention to the camera. Avoid the sea water or rain to erode the camera.
5. Handle carefully
Do not allow this series product fall down to the ground.
Avoid heavy vibration.
6. Installation Environment Requirement
zThis series speed dome should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
zThis series product shall be away from the strong electromagnetism radiant, please keep it
away from wireless power, TV transmitter, transformer and etc.
7. Daily Maintenance
zPlease use the soft cloth to clean dust on the shell, or you can use soft cloth with cleaning
liquid to clean the shell and then use soft cloth to make it dry.

vii
zDo not use gasoline, dope thinner or other chemical material to clean the shell. It may result
in shell transfiguration or paint flake.
zDo not allow the plastic or rubber material to touch the shell for a long time. It may result in
paint flake.

1
1INTELLIGENT SPEED DOME INSTALLATION
1.1 Installation Environments
Basic Requirement
zAll installation and operation here should conform to your local electrical safety codes.
zBefore installation, please open the package and check all the components are included.
Please make sure the speed dome installation environment and installation mode can meet
your requirement. If there is special requirement, please contact your local retailer for more
information.
zWe assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
1.2 Check installation space and installation location intension
Please make sure the installation environment has enough space to install the speed dome and
its corresponding bracket.
Please make sure the ceiling, wall and the bracket can support the speed dome and its
corresponding installation component. It shall sustain the 8X weight of the speed dome.
1.3 About cable
Please select the cable according to your transmission distance.
The minimum video coaxial-cable requirement is:
z75 ohm.
zFull cable with copper conductor
z95% knitted copper shield
International Model Max Distance
(Ft\M)
RG59/U 750ft (229m)
RG6/U 1,000ft (305m)
RG11/U 1,500ft (457m)
zPlease refer to Appendix 2 for RS485 communication cable information.
Select eclectic wire according to your transmission distance:
zFor 24V AC series product, please refer to Appendix 3.
zFor 12V DC series product, please refer to Appendix 4.
1.4 Please keep all package material well for future use
Please keep speed dome package material well in case you need to send it back to your local
retailer or manufacturer for maintenance work.
Non-original package material may result in device damage during the transportation.

2
2SETUP BEFORE INSTALLATION
2.1 Check Accessories
Before the installation, please check the accessories one by one according to the packing list.
Please make sure all the components listed are included.
2.2 Open Device
This section is for intelligent analog speed dome, intelligent network speed dome, and intelligent
tracking speed dome.
Remove the package and then take out the device. Open the transparent cover and take out the
packing material EPE around the speed dome drive. Please remove the paster from the pedestal.
See Figure 2-1.
Figure 2-1
2.3 Initial Setup
The default setup is:
zAddress: 1
zBaud rate: 9600
zParity: None
z120Ωresistance: OFF

3
2.4 Dial Switch Setup (For Analog Speed Dome Only)
The following operation is based on the ceiling mount speed dome. Here we are going to set
speed dome address, baud rate and etc. There are two dial switches on the PTZ for you to set
address, baud rate and etc. See Figure 2-2.
Figure 2-2
2.4.1 Dial Switch Buttons
Before you control speed dome, please set the speed dome address, baud rate, parity.
Otherwise, you can not control the device! See Figure 2-3.
Open speed dome transparent enclosure, you can view the dial switch buttons on the PTZ main
board. You can follow the steps listed below to set the speed dome address, baud rate, and
parity. Please note you need to restart the device to activate the new setup!
For wall mount speed dome, you need to take out the packing material EPE, set the dial switch
buttons and then put it back to the transparent enclosure module.

4
Figure 2-3
There are two dial switch buttons on the PTZ. You can use them to set speed dome address,
baud rate, and parity respectively. It is 1 when you set the button as ON.
For the protocol dial switch, you can refer to the following sheet. 1 is the lowest bit and the 8 is
the highest bit.
Please note the intelligent speed dome can automatically recognize the industrial
standard protocol, PELCO-D. PELCO-P. Usually you do not need to set the protocol.
2.4.2 Baud Rate and Parity Setup
For the dial switch button 1-4. 1 and 2 is to set baud rate. 3 and 4 is to set parity. Please refer to
the following figure for detailed information. See Figure 2-4.
Figure 2-4
Please refer to the baud rate sheet for detailed information.
1 2 Baud Rate
OFF OFF 9600bps
ON OFF 4800bps
OFF ON 2400bps
ON ON
1200bps
Please refer to the parity setup sheet for detailed information.
3 4 Parity
OFF OFF NONE
ON OFF EVEN
OFF ON ODD

5
ON ON NONE
2.4.3 Address
The address interface is shown as in Figure 2-5.
Figure 2-5
The encode mode adopts binary system. 1 to 8 is valid bit. The highest address bit is 255. You
can refer to the following sheet for more information.
Address 1 2 3 4 5 6 7 8
1 OFF OFF OFF OFF OFF OFF OFF OFF
1 ON OFF OFF OFF OFF OFF OFF OFF
2 OFF ON OFF OFF OFF OFF OFF OFF
3 ON ON OFF OFF OFF OFF OFF OFF
4 OFF OFF ON OFF OFF OFF OFF OFF
5 ON OFF ON OFF OFF OFF OFF OFF
6 OFF ON ON OFF OFF OFF OFF OFF
7 ON ON ON OFF OFF OFF OFF OFF
8 OFF OFF OFF ON OFF OFF OFF OFF
…… …………………………………………………………………
254 OFF ON ON ON ON ON ON ON
255 ON ON ON ON ON ON ON ON
2.4.4 Terminal Matching Resistance Setup
There is terminal resistance 120Ωon the main board. There are two modes: See Figure 2-6.
Figure 2-6
The factory default setup is shown as in Figure 2-7. Right now, the jumper (Connection board) is
on the pin 2 and pin 3. The 120Ωresistance does not connect to the device.
Figure 2-7
1-2 2-3
120ΩON OFF

6
If you want to connect the 120Ωresistance, please remove the jumper from the pin 2 and pin 3
and connect to pin 1 and pin 2. Now the 120Ωis connected to the circuit. See Figure 2-8.
Figure 2-8

7
3CEILING MOUNT
3.1 Installation Components
The ceiling mount installation component is shown as in Figure 3-1.
Figure 3-1
3.2 Ceiling Mount Installation Steps
3.2.1 Installation Environments
The ceiling mount speed dome can be installed in the hard construction wall in the indoor
environments. Before the installation, please make sure:
zThe wall is thick enough to install the expansion bolt.
zThe ceiling can at least sustain the 8x weight of the speed dome, bracket and the
accessories.
3.2.2 Installation Steps
1) The ceiling installation has two cable exit modes: One is to pull the cable through the
side cable exit of the speed dome without dig holes on the ceiling. The other is to dig
holes on the ceiling and pull the cable through the ceiling.
2) Confirm installation position and cable exit mode. Use the ceiling installation position
map to dig holes on the ceiling and then put the four plastic expansion bolts firmly.

8
3) In Figure 3-2, pull the cable according to your cable exit mode. And then use four
screws (working with insulated sleeve) to secure the pedestal of ceiling mount speed
dome on the ceiling. Turn the screws to the plastic expansion bolts.
Figure 3-2
4) In Figure 3-3, line up the arrow symbol on the speed dome external enclosure to the bar
symbol of the pedestal. Use three screws (provided) to secure the external enclosure
on the pedestal and fix firmly.
Figure 3-3

9
3.2.3 Cable Connection
The step listed below is for ceiling, in-ceiling or wall mount series product.
Please connect the power cable, video output cable, RS485 control cable, alarm input/output pin
of the intelligent speed dome composite cable according to your actual requirements. Pleas use
insulation tape to seal the cable connection ports to do proper waterproof work.
Note
The video port is covered the heat shrink tube of high shrinking ratio. After the video
connection, please heat the tube to make sure the video port is damp proof and water
proof.

10
4WALL MOUNT BRACKET INSTALLATION
4.1 Component Installation
The wall mount bracket and outdoor speed dome is shown as in Figure 4-1.
Figure 4-1
4.2 Wall Mount Installation Steps
4.2.1 Installation Environments
The wall mount speed dome can be installed in the hard construction wall in the indoor or
outdoor environments. Before the installation, please make sure:
zThe wall is thick enough to install the expansion bolt.
zThe ceiling can at least sustain the 8x weight of the speed dome, bracket and the
accessories.
4.2.2 Installation Steps
1) Dig a hole of 50mm diameter for cable exit in the installation wall.
2) In Figure 4-2, connect the adapter block to the internal thread of the wall mount bracket,
until it reaches the end and then fix the set screw. Pull the intelligent speed dome
composite cable through the adapter block and pull it out of the other end of the wall
mount bracket. Line up the hook at the top of the external enclosure to the inside hole of
the adapter block and then push it to the end, and then secure the three screws of the
adapter block firmly. Please note this step is very important. Please make sure the
screws are firm, otherwise, it may result in falling risk of the intelligent speed
dome.

11
Figure 4-2
3) Dig holes in the wall according to the installation holes at the bottom of the wall mount
bracket. Please make sure the cable exit of the bracket is facing the round hole of the
wall. Insert expansion bolts (not provided) to the holes you just dug. Connect the
composition cable and then pull it through the hole in the wall. Use four hex screws and
flat washer to secure the bracket on the wall of the expansion bolts. See Figure 4-3.
Figure 4-3

12
Now the installation is complete. See Figure 4-4.
Figure 4-4