Honeywell H4 series User manual

Document 800-13172V2 – Rev A – 05/2013
Document 800-13172V2 – Rev A – 05/2013
H4 Series
ONVIF True Day/Night Rugged IP Minidome Camera
Quick Install Guide
Introduction
Thank you for purchasing a Honeywell H4 Series True Day/Night Rugged IP Minidome Camera.
Before installing the camera, please read this guide carefully and verify your model:
equIP Series
H4D1F/H4D1FX, 720p resolution, 3.3 - 12 mm Vari-focal Auto Iris
H4D2F/H4D2FX, 1080p resolution, 2.9 - 9 mm Motorized Focus and Zoom (MFZ) lens
H4W1F/H4W1FX, Wide Dynamic, 720p resolution, 3.3 - 12 mm Vari-focal Auto Iris lens
Performance Series
H4S1P/H4S1PX, 720p resolution, 3.3 - 12 mm Vari-focal Auto Iris lens
H4SVP/H4SVPX, VGA resolution, 3.3 - 12 mm Vari-focal Auto Iris lens
For detailed information for your specific camera, please refer to the appropriate user guide
located on the IP Utility DVD. When you install the Honeywell IP Utility software, the User Guide
will automatically be downloaded to your computer.
Before installing the camera, Honeywell recommends that you download the latest software
updates. Go to http://www.honeywellsystems.com/support/download-center/index.html and
follow the instructions on the page to log on, find your camera, and then download software
updates.
Preparing the Mounting Surface
Note To prevent moisture from entering the housing, position the enclosure with the side conduit entry
pointing down.
Note The housing is intended for mounting on a flat surface only.
1. Use the mounting template to mark the mounting surface for the screw holes and the cable access
hole.
2. Pre-drill holes in the mounting surface as required.
Installing the Conduit Plug
The HD4 equIP Series camera ships with
the conduit plug pre-installed in the
enclosure base back conduit entry. To use
the back conduit entry, remove the conduit
plug and install it in the side conduit entry
after loosening the locking screw. (See Top
View in Adjusting the Camera in Camera
Installation.) Retighten the locking screw to
secure the conduit plug in place.
Note For secure installations, protect
surface-mounted cables with
plastic or metal cable covers.
Preparation
Black tabs (x4)
Black clips (x4)
Metal
hinge Mounting
holes
Gimbal
Dome bubble Turret
Removing the Dome Bubble and
Turret
1. Using the supplied Allen key, loosen the captive
screws on the dome bubble. Remove the dome
bubble and set it aside.
2. Gently pull the turret off the gimbal, then set it aside.
Removing the Gimbal
Remove the gimbal from the enclosure base so you can
easily access the mounting holes (see illustration).
1. Squeeze the 4 black tabs until they are free of the
black clips.
2. Elevate the hinge until the gimbal is above the
housing and you have access to the enclosure base
mounting holes.
Caution When elevating the hinge, do not overstress the
two ribbon cables.
If necessary, rotate the gimbal to provide
additional slack.
1
Side
conduit
entry
Back conduit entry
Enclosure base
Conduit
plug locking
screw
Conduit plug
Screws
Rubber washer
Please turn over
Camera Installation
2
Mounting the Camera
1. Route the cables through your chosen conduit entry.
2. Mount the camera to a wall or ceiling using the supplied screws.
If you are using screws other than those supplied by Honeywell, then please remove the rubber
washers from the Honeywell-supplied screws, and then install them under the head of each of
your screws. See the Installing the Conduit Plug illustration.
Connecting the Wiring
1. Connect the power input:
• For 24 V AC connection, locate the two-pin green connector that was shipped with
your camera and make the necessary connections.
• For PoE connection, connect a CAT5 cable to the RJ45 network connector.
Note It is not recommended that you supply both 24 V AC and PoE at the same time.
2. Connect the alarms and audio:
Locate the eight-pin green connector that was shipped with your camera and make all the
necessary connections as shown in the table below.
3. Connect to the network:
If you haven’t already connected a CAT5 cable to the RJ45 network connector for PoE,
then connect a CAT5 cable to the RJ45 network connector.
Note For detailed audio and alarm configuration information, refer to the Reference Guide for
your camera located on the IP Utility DVD.
Sealing the Wiring
To prevent moisture from entering the housing, if you are using the back conduit entry, apply
sealant around the conduit connection and the mounting screws.
Power: 24V AC
RJ45 Ethernet network connection
Audio/Alarms
Local video out (adjusting and focusing)
In Out
Audio Alarm
In Out
24V AC
12345678
PIN Definition
1 Audio In +
2 Audio In –
3AudioOut+
4AudioOut–
5 Alarm In +
6 Alarm In –
7 Alarm Out +
8 Alarm Out –
Note The Audio and Alarm I/O connections are not available on H4SVP and H4S1P cameras.
Operating Notes
Power Supply This dome camera can operate on 24 V AC or PoE.
Operating Conditions Avoid:
• Viewing bright objects (for example, light fixtures) for
extended periods
• Operating or storing the unit in the following locations.
• Extremely humid, dusty, hot/cold environments [where
the operating temperature is outside the recommended
range of:
H4D2F(X) -4°F to 122°F (-20°C to 50°C)
H4D1F(X) -22°F to 140°F (-30°C to 60°C)
H4S1P(X)/H4SVP(X) -4°F to 122°F (-20°C to 50°C)
H4W1F(X) -13°F to 131°F (-25°C to 55°C)]
• Close to sources of powerful electromagnetic radiation,
such as radio or TV transmitters
• Close to fluorescent lamps or objects reflecting light
• Under unstable light sources (may cause flickering)

The camera has a web client that enables you to view video and configure device
settings for the camera using a standard web browser. See the appropriate user guide
located on your software DVD to set up your web browser to view video. To log on to
the web client application:
1. Launch Internet Explorer and enter the URL (IP address) for the network camera.
OR, launch the web client application from the IP Utility by clicking Launch
Browser.
2. Select the User Name as admin or Guest.
3. Enter the case-sensitive password and click . The default passwords are 1234
(Administrator) or guest (Guest user).
Camera Operation
4
Contact Information
www.honeywellvideo.com
+1.800.323.4576 (North America only)
[email protected]
Document 800-13172V2 – Rev A – 05/2013
© 2013 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any
means without written permission from Honeywell. The information in this publication is believed to be
accurate in all respects. However, Honeywell cannot assume responsibility for any consequences resulting
from the use thereof. The information contained herein is subject to change without notice. Revisions or new
editions to this publication may be issued to incorporate such changes.
Network Setup
Installing the Honeywell IP Utility
Note Before installing and using the Honeywell IP Utility, ensure that your camera is
connected to your network through a CAT5 Ethernet cable.
To discover the IP camera devices and configure their network settings, you must first
install the IP Utility. See the appropriate user guide located on your software DVD or on
the Honeywell product web site. You must have Windows administrator privileges for
the workstation on which the Honeywell IP Utility is being installed.
Note We recommend that you disable any Norton AntiVirus software that might be
running on the workstation.
1. Insert the DVD. Autorun will start the installation. If autorun does not start, browse
to the DVD drive and run Honeywell IP Utility Setup.exe.
2. Follow the steps in the InstallShield Wizard.
3. Log on to the IP Utility by double-clicking the IP Utility icon ( ) on the desktop.
The main IP utility screen appears.
Note This camera supports the ONVIF™ specification for interoperability between
network video products. There is no support for legacy equIP and equIP2
products.
Configuring the Network
1. After you log on to the IP utility, the devices on the network are automatically
discovered and listed in the Discovery pane. After the initial discovery, auto-
refresh continues to discover newly added network devices.
2. Connect to your IP camera device by double-clicking it in the Discovery pane or
by selecting it and clicking .
3. Configure the IP network settings:
•Automatically. Connect to the device, click the System tab, select to
Obtain an IP Address automatically, enter the Device Name, and click
Apply. The network settings are automatically assigned from the network
server.
•Manually. Connect to the device, click the System tab. Ensure Obtain an
IP Address automatically is not selected, then enter the Device Name, IP
Address, Subnet Mask, and Gateway. Click Apply.
Caution Check the IP network settings before clicking Apply. Incorrect values might
cause a failure when connecting the tool to the device.
Note Contact your network administrator if you have any network-related issues or
questions about your network.
3FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the limits for a
Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his
own expense.
Caution Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
North America
The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No. 60950-1.
Manufacturer’s Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with the
essential protection requirements of the EMC directive 2004/108/EC and the General Product
Safety Directive 2001/95/EC, conforming to the requirements of standards EN 55022 for emissions,
EN 50130-4 for immunity, and EN 60950 for Electrical Equipment safety.
WARNING! This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to
take adequate measures.
Warnings
Installation and servicing should be performed only by qualified and experienced technicians to
conform to all local codes and to maintain your warranty.
WARNING! 24V AC models require the use of CSA Certified/UL Listed Class 2 power
adapters to ensure compliance with electrical safety standards. Power over
Ethernet (PoE) should meet the IEEE 802.3 af PoE standard.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product
(applicable in the European Union and other European countries with separate collection
systems). This product should be disposed of, at the end of its useful life, as per applicable
local laws, regulations, and procedures.
Adjusting the Camera
1. Verify that power is applied to the camera.
Note If your installation involves a 24 V AC power source, then please wait approximately 60
seconds after connecting to a power source for video to appear on the local video out.
2. Reinstall the gimbal by inserting the black tabs into the black clips on the enclosure base.
3. Connect the supplied video cable to the local video out connector to view the video signal
on a standard monitor (see illustration below for local video out connector location).
4. Loosen the setscrew that locks the gimbal assembly in place to adjust the horizontal
rotation.
5. Adjust the camera to the desired view.
6. Retighten the setscrew to lock the gimbal assembly in place.
7. Disconnect the supplied video cable.
Reinstalling the Turret and the Dome Bubble
1. Align the turret on the gimbal, then gently press until the turret clicks securely into place.
2. Align the dome bubble captive screws with the mounting holes in the enclosure base, then
securely screw them into place.
Legend
A = Tilt rotation
B = Horizontal rotation
C = Pan rotation
B
C
A
Setscrew (loosen to
adjust horizontal
rotation)
Set focus
(top)
Set focal length
(bottom)
Top View
Loosen locking
screw (inside
conduit entry) to
remove the side
conduit plug
Reset
button
Local video
out
H4D1F(X) / H4W1F(X) / H4SVP(X) / H4S1P(X)
Adjust the horizontal, pan, and tilt rotations so that the area of interest is at the center
H4D2F(X)
Adjust the horizontal, pan, and tilt rotations so that the area of interest is at the center.
Final zoom and focus adjustments can be made using the camera’s web client.
Loosen locking
screw (inside
conduit entry) to
remove the side
conduit plug
Setscrew (loosen to
adjust horizontal
rotation)
Reset
button
Local video
out
Top View
Legend
A = Tilt rotation
B = Horizontal rotation
C = Pan rotation
A
C
B