Eclipse ThermJet TJSR0020 User manual

Eclipse ThermJet
Self-Recuperative Burners
Models TJSR0020 - TJSR0100
Installation Guide 208
2/4/2013
Version 5

2
Copyright
Copyright 2007 by Eclipse, inc. All rights reserved
worldwide. This publication is protected by federal
regulation and shall not be copied, distributed,
transmitted, transcribed or translated into any human or
computer language, in any form or by any means, to any
third parties, without the express written consent of
Eclipse, inc.
Disclaimer Notice
In accordance with the manufacturer’s policy of continual
product improvement, the product presented in this
brochure is subject to change without notice or obligation.
The material in this manual is believed adequate for the
intended use of the product. If the product is used for
purposes other than those specified herein, confirmation
of validity and suitability must be obtained. Eclipse
warrants that the product itself does not infringe upon any
United States patents. No further warranty is expressed or
implied.
Liability & Warranty
We have made every effort to make this manual as
accurate and complete as possible. Should you find errors
or omissions, please bring them to our attention so that we
may correct them. In this way we hope to improve our
product documentation for the benefit of our customers.
Please send your corrections and comments to our
Technical Documentation Specialist.
It must be understood that Eclipse’s liability for its product,
whether due to breach of warranty, negligence, strict
liability, or otherwise is limited to the furnishing of
replacement parts and Eclipse will not be liable for any
other injury, loss, damage or expenses, whether direct or
consequential, including but not limited to loss of use,
income, or damage to material arising in connection with
the sale, installation, use of, inability to use, or the repair
or replacement of Eclipse’s products.
Any operation expressly prohibited in this manual, any
adjustment, or assembly procedures not recommended or
authorized in these instructions shall void the warranty.
Document Conventions
There are several special symbols in this document. You
must know their meaning and importance.
The explanation of these symbols follows below. Please
read it thoroughly.
How To Get Help
If you need help, contact your local Eclipse representative.
You can also contact Eclipse at:
1665 Elmwood Rd.
Rockford, Illinois 61103 U.S.A.
Phone: [phone]
Fax: [phone]
http://www.eclipsenet.com
Please have the information on the product label available
when contacting the factory so we may better serve you.
Product Name
Item #
S/N
DD MMM YYYY
www.eclipsenet.com
This is the safety alert symbol. It is used to alert you to potential personal
injurt hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
Indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
Indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
Is used to address practices not related to personal injury.
Indicates an important part of text. Read thoroughly.
NOTE
NOTICE
CAUTION
WARNING

3
Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
Table of Contents
1 Introduction............................................................................................................................ 4
Product Description .............................................................................................................. 4
Audience .............................................................................................................................. 4
Purpose................................................................................................................................ 4
ThermJet Self-Recuperative Documents ............................................................................. 4
Related Documents.............................................................................................................. 4
2 Safety...................................................................................................................................... 5
Safety Warnings ................................................................................................................... 5
Capabilities........................................................................................................................... 5
Operator Training ................................................................................................................. 5
Replacement Parts...............................................................................................................5
3 Installation.............................................................................................................................. 6
Introduction........................................................................................................................... 6
Handling & Storage ..............................................................................................................6
Position of Components ....................................................................................................... 6
Approval of Components...................................................................................................... 6
Checklist Before Installation ................................................................................................. 7
Prepare the Burner............................................................................................................... 7
Furnace Wall Preparation..................................................................................................... 7
Burner Installation ................................................................................................................ 8
Valves................................................................................................................................... 10
Checklist After Installation ....................................................................................................11
Prepare for Adjustment ........................................................................................................ 11
4 Adjustment, Start, & Stop .....................................................................................................12
Introduction........................................................................................................................... 12
Adjustment Procedure.......................................................................................................... 12
Normal Operation Post Commissioning ............................................................................... 15
5 Maintenance & Troubleshooting.......................................................................................... 16
Introduction........................................................................................................................... 16
Maintenance......................................................................................................................... 16
Monthly Checklist ................................................................................................................. 16
Yearly Checklist.................................................................................................................... 16
Troubleshooting Guide......................................................................................................... 17
Appendix ................................................................................................................................... i
Conversion Factors ..............................................................................................................i

4Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
Introduction
Product Description
The ThermJet Self-Recuperative burner is a nozzle mix
burner that is designed to fire an intense stream of hot
gases through a combustor. It includes an integral
recuperator and eductor to draw exhaust gases through
the burner and preheat combustion air.
The high velocity of the gases improves temperature
uniformity, product quality and system efficiency.
Figure 1.1. Eclipse ThermJet
Self-Recuperative Burner
Audience
This manual has been written for personnel already
familiar with all aspects of a nozzle mixing burner and its
add-on components, also known as “the burner system”.
These aspects are:
• Installation
• Use
• Maintenance
• Safety
The audience is expected to be qualified and have
experience with this type of equipment and its working
environment.
Purpose
The purpose of this manual is to make sure that you carry
out the installation of a safe, effective, and trouble-free
system.
ThermJet Self-Recuperative Documents
Installation Guide No. 208
• This document
Datasheet No. 208-1 through 208-4
• Available for individual ThermJet Self-Recuperative
models
• Required to complete design and selection
Design Guide No. 208
• Used with Datasheet to design burner system
Worksheet No. 208
• Required to provide application information to
Eclipse Engineering
Spare Parts List Series No. 208
• Recommended replacement part information
Related Documents
• EFE 825 (Combustion Engineering Guide)
• Eclipse Bulletins and Info Guides: 610, 710, 720,
730, 742, 744, 760, 930
1

5
Safety
Important notices which help provide safe burner
operation will be found in this section. To avoid personal
injury and damage to the property or facility, the following
warnings must be observed. All involved personnel should
read this entire manual carefully before attempting to start
or operate this system. If any part of the information in this
manual is not understood, contact Eclipse before
continuing.
Safety Warnings
■The burners, described herein, are designed to mix
fuel with air and burn the resulting mixture. All fuel
burning devices are capable of producing fires and
explosions if improperly applied, installed,
adjusted, controlled or maintained.
■Do not bypass any safety feature; fire or explosion
could result.
■Never try to light a burner if it shows signs of
damage or malfunction.
■The burner and duct sections are likely to have
HOT surfaces. Always wear the appropriate
protective equipment when approaching the
burner.
■Eclipse products are designed to minimize the use
of materials that contain crystalline silica.
Examples of these chemicals are: respirable
crystalline silica from bricks, cement or other
masonry products and respirable refractory
ceramic fibers from insulating blankets, boards, or
gaskets. Despite these efforts, dust created by
sanding, sawing, grinding, cutting and other
construction activities could release crystalline
silica. Crystalline silica is known to cause cancer,
and health risks from the exposure to these
chemicals vary depending on the frequency and
length of exposure to these chemicals. To reduce
the risk, limit exposure to these chemicals, work in
a well-ventilated area and wear approved personal
protective safety equipment for these chemicals.
■This manual provides information regarding the
use of these burners for their specific design
purpose. Do not deviate from any instructions or
application limits described herein without written
approval from Eclipse.
Capabilities
Only qualified personnel, with sufficient mechanical
aptitude and experience with combustion equipment,
should adjust, maintain or troubleshoot any mechanical or
electrical part of this system.
Operator Training
The best safety precaution is an alert and trained
operator. Train new operators thoroughly and have them
demonstrate an adequate understanding of the
equipment and its operation. A regular retraining schedule
should be administered to ensure operators maintain a
high degree of proficiency.
Replacement Parts
Order replacement parts from Eclipse only. All Eclipse
approved valves or switches should carry UL, FM, CSA,
CGA and/or CE approval where applicable.
DANGER
WARNING
NOTICE
2

6Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
Installation
Introduction
In this section you will find the information and instructions
needed to install the burner and system components.
Handling & Storage
Handling
• Make sure the area is clean.
• Protect the components from weather, damage, dirt
and moisture.
• Protect the components from excessive
temperatures and humidity.
Storage
• Make sure the components are clean and free of
damage.
• Store the components in a cool, clean, dry room.
• After making sure everything is present and in good
condition, keep the components in original
packages as long as possible.
Position of Components
The position and amount of components are determined
by the kind of control method chosen. All the control
methods can be found in Design Guide 208, Chapter 3
“System Design.” Use the schematics in that chapter to
build your system.
Approval of Components
Limit Controls & Safety Equipment
All limit controls and safety equipment must comply with
all applicable local codes and/or standards and must be
listed for combustion safety by an independent testing
agency. Typical application examples include:
• American: NFPA 86 with listing marks from UL, FM,
CSA
• European: EN 746-2 with CE mark from TuV,
Gastec, Advantica
Electrical Wiring
All the electrical wiring must comply with all applicable
local codes and/or standards such as:
• NFPA Standard 70
• IEC60364
• CSA C22
• BS7671
Gas Piping
All the gas piping must comply with all applicable local
codes and/or standards such as:
• NFPA Standard 54
• ANSI Z223
• EN 746-2
Where to Get the Standards:
The NFPA Standards are available from:
National Fire Protection Agency
Batterymarch Park
Quincy, MA 02269
www.nfpa.org
The ANSI Standards are available from:
American National Standard Institute
1430 Broadway
New York, NY 10018
www.ansi.org
The UL Standards are available from:
333 Pfingsten Road
Northbrook, IL 60062
www.ul.com
The FM Standards are available from:
1151 Boston-Providence Turnpike
PO Box 9102
Norwood, MA 02062
www.fmglobal.com/approvals
Information on the EN standards and where to get
them is available from:
Comité Européen de Normalisation
Stassartstraat 36
B-1050 Brussels
Phone: [phone]
Fax: [phone]
www.cen.eu
Comité Européen de Normalisation Electronique
Stassartstraat 36
B-1050 Brussels
Phone: [phone]
Fax: [phone]
www.cenelec.org
3

7
Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
Checklist Before Installation
Air Supply
Provide an opening in the burner room of at least one
square inch per 10,000 BTU/hr (6 cm2per 2.9 kW) to
supply the burner intake with fresh, outdoor, combustion
air.
If there are corrosive fumes or materials in the
surrounding air, find an uncontaminated source to supply
air to the burner, or provide a sufficient air filtering system.
Exhaust
Do not allow exhaust fumes to accumulate in the work
area. Provide some positive means for exhausting from
the furnace and the building.
Access
Make sure that you install the burner in such a way that
you can gain easy access for inspection and
maintenance.
Environment
Make sure the local environment matches the original
operating specifications. Check the following items:
• Voltage, frequency and stability of the electrical
power
• Fuel type and supply pressure of the fuel
• Availability of enough fresh, clean combustion air
• Humidity, altitude and temperature of air
• Presence of damaging corrosive gases in the air
• Prevent direct exposure to water
Prepare the Burner
Several components must be installed on a burner before
it can operate.
Install the igniter in the burner before installing the burner.
See “Step 5: Igniter and Flame Sensor Installation”.
Furnace Wall Preparation
Make sure the furnace wall is capable of supporting the
weight of the burner to be installed. If necessary, reinforce
the mounting area. A round opening approximately 0.5"
(12.7 mm) larger than the OD of the ceramic exhaust tube
must be provided in the casing of the furnace. A larger
hole through the refractory is acceptable and should be
filled with insulation.
To verify proper burner position within the furnace wall,
determine the burner length. Measure from the exhaust
housing mounting face to the tip of the combustor. This is
the burner length. Compare the burner length to the
furnace wall thickness plus the mounting extension length
plus the exhaust tube flange thickness. The burner length
should be shorter by 0 to 1" (25 mm).
Figure 3.1 Burner Position Verification
Minimum gap is
1/8" (3mm). If this
gap is larger than 1/2"
(12mm) fill it with
insulation.
Position the tip of
the combustor tube
approximately in
line with the
furnace wall.

8Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
Burner Installation
Step 1
Refer to Quick Guide 208 for unpacking information.
Step 2: Mounting Extension Installation
The mounting extension must be bolted to the casing of
the furnace. Four studs must be provided on the furnace
casing to mate with the mounting extension. In order to
ensure proper alignment of the mounting flange:
1. Center the mounting extension on the opening in the
furnace wall.
2. Ensure the face of the mounting extension is
perpendicular to the center line of the opening.
3. Rotate the mounting extension such that it is square
with respect to the vertical center line of the clearance
hole in the furnace.
4. Bolt mounting extension to the furnace casing. See
Figure 3.2.
Figure 3.2 Mounting Extension Installation
Figure 3.3
Step 3: Exhaust Tube Installation
1. Place gasket (a) over the exhaust tube.
2. Slide exhaust tube through mounting extension flange
into the furnace.
3. Place gasket (b) against exhaust tube flange. Use
adhesive spray to hold gaskets in place. See Figure
3.4.
4. Gently place the adapter ring over the flange of the
exhaust tube. The recess on the adapter ring must
face the exhaust tube flange. The adapter ring should
sit flush with the mounting extension.
5. Bolt adapter ring to mounting extension.
NOTE: Use anti-seize compound on all bolts when
assembling.
Figure 3.4
■Ceramic exhaust tube must be secure between
mounting extension and adapter plate. If not,
exhaust tube may break.
6. Complete preparation inside the furnace. See Figure
3.1
Step 4: Burner Installation
It is important to use mechanical lifting assistance when
installing the burner. Do not allow the burner to become
tilted during installation. See Figure 3.6.
Figure 3.5
Mount burner and gasket in the exhaust tube (see Figures
3.5 and 3.6) by aligning holes in exhaust housing with
studs on mounting extension.
Insulation
Furnace
Studs
Mounting
Extension
Exhaust
Tube
Gasket b
Adapter
Ring
Gasket a
Mounting
Extension
CAUTION

9
Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
■Do not allow the ceramic combustor to carry the
weight of the burner or the combustor will break.
Figure 3.6
NOTE: The burner may require centering to assemble.
Nuts and bolts should be torqued to 15-20 ft-lbs (20-27
Nm) cold and re-torqued at operating temperature and
after 100 hours of operation. Position housing so air inlet
is oriented to align with the air manifold piping.
Step 5: Igniter
1. If already assembled, remove the rear cover
assembly by removing rear cover bolts. See Figure
3.9.
2. Thread igniter through rear cover and hole in nozzle.
See Figure 3.7 for burners without spark rod cooling
and Figure 3.8 for models with cooling.
NOTE: Do not apply any grease to the threads of the
spark plug. You can cause bad grounding of the spark
plug if you apply grease to it. Bad grounding of the spark
plug results in a weak spark.
3. Slide the rear cover nozzle assembly through the air
inlet housing and into the combustor assembly. See
Figure 3.9.
4. Assemble the rear cover to the air inlet housing using
cap screws. Torque to 5 ft-lbs (7 Nm). Position cover
so gas inlet is aligned with gas manifold piping.
Figure 3.7
Figure 3.8
Figure 3.9
Step 6: UV Flame Sensing
1. Install the flame sensor into the designated opening in
the rear cover. See corresponding datasheet series
208 for proper location.
2. Make sure that the UV scanner is connected to the
electrical circuit of that burner.
■Connecting the UV scanner of a burner to the
electrical circuit of a different burner can cause
fires and explosions.
The UV scanner must be compatible to the flame
monitoring control that is used. Refer to the manual of
your selected control for proper selection of the scanner.
■Adjustments may vary from Eclipse published
values if the flame controls other than those
recommended in the Design Guide are used.
Consult with the engineer who specified the
alternate control for limitations.
CAUTION
CORRECTWRONG
10 ± 2 mm
10 ± 2 mm
Spark rod cooling tube
should be flush with the nozzle
Rear Cover Nozzle
Assembly
Rear Cover
Bolts
Air
Inlet
Housing
DANGER
NOTICE

10 Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
Figure 3.10 Flame Sensor Installation
Step 7: Piping
Install the piping as shown in the schematics. Refer to
Chapter 3 of the Design Guide No. 208.
Support the Piping
Use brackets or hangers to support the gas piping. If you
have questions, consult your local gas company.
Straight Run of Pipe Before a Metering Orifice
NOTE: There must be a run of pipe with a straight length
of at least 10 pipe diameters before the burner metering
orifice. Failure to provide this length will result in
inaccurate pressure readings, and poor burner operation.
Pipe Connections
Install a pipe union in the gas line to the burner. This
simplifies removal of the burner.
NOTE: Flexible pipe nipples will cause inaccurate
metering orifice readings if installed in the burner inlet and
may cause higher pressure drops than equivalent
standard pipe. Consider this when sizing the gas lines.
Avoid Large Pressure Drops
NOTE: Pressure drop in the piping is a critical parameter.
Make sure that the size of all the piping is large enough to
prevent excessive pressure losses.
Eductor
NOTE: There should be no direct pipe connection to the
eductor outlet. This may effect eductor performance.
There should be at least a 2 inch (50mm) gap between the
eductor outlet and the exhaust duct or cowl.
Step 8: Pressure Taps
There are two sets of air and gas pressure taps for
differential pressure measurements. In addition, there is a
static air pressure tap that can be used to verify air
pressure.
Valves
Valve Orientation
Install all the valves in such a way that the arrow (if
present) on the valve body points in the direction of flow.
Figure 3.11 Valve Orientation
Gas Cocks
Make sure that the handle of a gas cock is at a right angle
to the valve body when the valve is in the closed position.
This is an important position indicator.
Balancing Valves
A gas balancing valve is either an adjustable limiting
orifice valve or a manual butterfly valve. An air balancing
valve is typically a manual butterfly valve. For more
information, refer to the following sections.
Manual Butterfly Valves
• Install manual butterfly valves in accordance with
Bulletin / Info Guide 720.
Adjustable Limiting Orifice Valves
• Install adjustable limiting orifice valves in
accordance with Bulletin 728/730.
NOTE: It is recommended that there is a run of pipe with
a length of at least 10 pipe diameters between any flow
altering device and the metering orifice on the burner.
Automatic Butterfly Valve
An automatic butterfly valve is driven by an actuator
(actuator and mounting bracket not illustrated).
• Install the control valve in accordance with Bulletin/
Info Guide 720.
Figure 3.12 Butterfly Valves
Ratio Regulator
Connect an impulse line to the ratio regulator and to the
air supply line.
NOTE: All settings in this document assume the use of a
Dungs FRG Ratio Regulator. Use of a different Ratio
Regulator may result in improper burner operation.
UV Scanner Location
Flame Sensor;
UV Scanner
Closed Open
Manual Automatic

11
Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
NOTE: The inlet gas pressure to the ratio regulator must
be a minimum of 5" w.c. (12.5 mbar) higher than the
impulse line pressure at high fire condition.
Step 9: Spark Rod Cooling Option
If applicable, connect flex hose to air cooling connections
as shown in Figure 3.13.
Figure 3.13
Checklist After Installation
To verify the system was properly installed, perform the
following checks:
1. Be sure there are no leaks in the gas lines.
2. Be sure all the components contained in the flame
monitoring and control system are properly installed.
This includes verifying that:
• all the switches are installed in the correct locations.
• all wiring, pressure, and impulse lines are properly
connected.
3. Be sure all components of the spark ignition system
are installed and functioning properly.
4. Be sure the blower rotates in the proper direction. If
the rotation is incorrect, have a qualified electrician
rewire the blower to rotate in the proper direction.
5. Be sure all valves are installed in the proper location
and correctly oriented relative to the flow direction.
Prepare for Adjustment
After installation of the burner system components is
complete, the following steps should be followed in order
to prepare for adjustment:
1. Set the air pressure switch so that it drops out at 4"
w.c. (10 mbar) below the pressure rating of the blower.
2. Set the low gas pressure switch at 4" w.c. (10 mbar)
below the gas pressure measured at the inlet to the
main gas valve train.
3. Set the high gas pressure switch so that it comes on
at 4" w.c. (10 mbar) above the gas pressure
measured at the inlet to the main gas valve train.
4. Close all the burner gas cocks.
5. Try to light a burner before the purge and other timers
have finished their cycles. Make sure that the flame
monitoring system indicates a flame failure.
6. Trip out pressure switches and other limit interlocks.
make sure that the main gas valve train closes.
■If simulated limits or simulated flame failures do
not shut down the fuel system within the required
failure response time, immediately correct the
problem before proceeding.
Flex
Hose DANGER

12 Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
Adjustment, Start &
Stop
Introduction
In this chapter, you will find instructions on how to adjust,
start, and stop the burner system. Become familiar with
burner control methods before attempting to make
adjustments.
■Do not bypass any safety feature; fire or explosion
could result.
■Never try to light a burner if it shows signs of
damage or malfunction.
Adjustment Procedure
Step 1: Reset the System
1. Close the automatic gas valves and the gas cocks.
2. Fully open the manual air butterfly valve at each
burner and eductor. Drive the automatic zone air
control valve to high fire. Adjust the automatic zone air
control valve so that it is fully open.
3. Start the blower.
■Make sure that the blower rotates in the correct
direction. If incorrect, have a qualified electrician
rewire the blower to reverse its rotation.
Step 2: Set Eductor
The eductor can be adjusted to pull all the exhaust gases
through the burner, at this setting it will provide
approximately neutral pressure in the furnace chamber.
Using this method it is not possible to use furnace
pressure control.
An alternative method, where more precise furnace
pressure control is required, is to pull only 90% of the
exhaust gases through the burner. The remaining 10% of
exhaust gas would exit through an auxiliary flue with
furnace pressure control. The datasheet provides the
Eductor butterfly valve settings to be used for both
methods and different chamber temperatures.
Set the integral butterfly valve to the appropriate position
for the desired chamber temperature and exhaust
requirement. See the appropriate datasheet in series 208.
To adjust the integral butterfly valve it will be necessary to
loosen the two locking screws, retighten after adjustment.
There are two scales on the eductor, numbering 0 to 6.
The pointer must be on the opposite side of the burner as
the air inlet. Example, if the air comes in on the right side
of the burner, the indicator pin must point to the number
on the left side of the label. See Figure 4.1.
Figure 4.1. Right Side Air Inlet Shown
NOTE: These settings are for a neutral chamber
pressure. For settings for a positive or negative chamber
pressure please contact Eclipse.
Step 3: Set High Fire Air
1. Set the system to high fire, but DO NOT ignite the
burner (s).
2. The initial settings for the air should match the static
pressure listed in the datasheet for the temperature of
your furnace. This is only the initial setting, as the
furnace temperature increases the pressure will
change and further adjustment will be required.
3. Set high fire air.
NOTE: A pressure tap is open when the screw inside the
tap is unscrewed approximately half a turn.
DANGER
CAUTION
Set Eductor
Indicator
Using this Side
of the Scale
for RH Air Inlet
Air
Inlet
4

13
Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
Figure 4.2. Butterfly Valve Location
Single Burner
a.Make sure that pressure taps A and C on the burner
are open.
b.Connect a manometer to taps A and C.
c.Confirm that the eductor butterfly valve is set to the
correct position for the appropriate furnace
temperature and furnace pressure requirements.
d.Adjust the manual butterfly valve to achieve the
differential air target value at taps A and C.
e.Remove the manometer.
f.Close the pressure taps.
Multiple Burner System
a.Make sure taps A and C of the first burner is open.
b.Connect a manometer to taps A and C of the first
burner.
c.Confirm that the eductor butterfly valve is set to the
correct position for the appropriate furnace
temperature and furnace pressure requirements.
d.Adjust the manual butterfly valve to achieve the
required differential air target value at taps A and C.
e.For all the remaining burners in the zone measure
and note the differential air pressure at taps A and
C.
f.If all the measured differential pressures are within
0.5" w.c. (1.25 mbar) of each other, then proceed to
the next section. If the variation is greater than 0.5"
w.c. (1.25 mbar) it will be necessary to adjust the
manual air butterfly valve at each burner to improve
the balance.
g.Make sure that all the pressure taps are closed.
h.Repeat step 3 for other zones (if any).
Step 4: Set Low Fire Air (if applicable)
1. Set the system to low fire.
2. Connect the manometer to Taps A and C (air orifice
pressure differential).
3. Adjust the minimum setting at the automatic zone air
control valve until the low fire air differential pressure
between taps A and C matches the Minimum Low Fire
Air Pressure Drop in the datasheet. This is the initial
setting only. Further adjustment may be required.
4. Repeat steps 2 and 3 for the other zones (if any).
Step 5: Verify the Air Settings
Make sure all the settings are still the same after you cycle
the system several times between high and low fire.
Step 6: Ignite the Burners
■This procedure is written with the assumption the
burner has a flame monitoring control system
installed and operating. A proper purge cycle must
be part of the system and purge timing should not
be bypassed.
1. Set the system to low fire.
2. Make sure the combustion air blower is running.
3. Set the manual gas valve at each burner to 50% open.
See Figure 4.3. If using an adjustable limiting orifice
valve, set it at 5 full 360° rotations up from the bottom.
Figure 4.3.Manual Gas Butterfly 50% Open
Figure 4.4.Adjusting Set Screw
4. Turn the adjusting screw on the Dungs FRG ratio
regulator counterclockwise until the screw cannot turn
any longer. From this position, turn the adjusting
screw 15 turns clockwise for the initial burner setting.
NOTE: Never turn the adjusting screw more than 15 turns
clockwise from the top. This may result in a gas rich
condition.
NOTE: If you are not using a Dungs FRG Ratio Regulator,
the settings in this document do not apply.
Manual Butterfly
Valve
WARNING
50% Open
Set Screw
Outer Dial

14 Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
5. Open zone manual gas cock. (Multi-burner systems
only.)
6. Open manual gas cock at each burner.
7. Initiate the ignition sequence through the flame
monitoring control system.
a.Check that all the burners in the zone have ignited.
b.If safety shut-off solenoid valves are installed at
each burner, then repeat steps 6 and 7 for all the
burners in the zone.
8. If all the burners have ignited, proceed to step 9. If
burners do not light, repeat step 7.
9. Drive the system to high fire and back down to low
fire, ensure the burners are still ignited.
10. If necessary, readjust the air pressure drop between
taps A and C until it matches the value in the
appropriate datasheet.
Step 7: Set High Fire Gas
1. Drive the system to high fire, ensure that all the
burners are ignited.
2. Check air pressures. With the burners firing check the
air pressure at the burners as described previously.
3. Use the gas curve from the appropriate ThermJet
Self-Recuperative datasheet for the gas being used to
find the differential gas pressure needed at high fire.
This is the target value for high fire.
4. Connect the manometer to taps B and D (across the
gas orifice).
5. Measure the high fire differential gas pressure for the
first burner.
6. Adjust the gas butterfly valve at the burner until the
gas flow is at the target value.
7. Repeat steps 3 through 4 for the other burners in the
zone.
8. Check the gas pressure at the inlet to the zone ratio
regulator. This should be at least 5" w.c. (12.5 mbar)
higher than the loading line pressure. It should not
exceed the maximum pressure rating of the ratio
regulator.
■Insufficient gas inlet pressure may cause the
proportionator to remain fully open as the burner
system turns down from high fire, causing excess
fuel operation and the possible accumulation of
unburned fuel in the chamber. In extreme cases,
this may cause explosions or fire.
9. When the furnace is at operating temperature, the air
pressures should be checked at high fire.
• Check the air differential pressure tap A to C. If
necessary, adjust the valve to achieve the desired
pressure. On multi-burner systems, check the
differential pressure A to C on all burners. If the
difference in pressure is greater than 0.5" w.c. (1.25
mbar) it will be necessary to adjust the air balance
using the valve.
• Check the differential gas pressure tap B to D at
each burner, if necessary adjust gas flow using
valve to achieve the required pressure.
If possible the O2level in the exhaust should be
checked. It must be noted that on multi-burner
installations the O2reading obtained at an individual
burner is influenced by other burners in the zone and
by any ingress of fresh air into the furnace.
The O2level measured will provide a measurement of
the general free oxygen in the furnace and should not
be used to set the air/gas ratio on the individual
burners.
On single burner installations O2reading will only be
influenced by the ingress of fresh air and can be used
to set the air/gas ratio with more confidence.
To measure the O2accurately, the probe must be
inserted into the exhaust at the side of the
recuperator.
NOTE: Increased O2level in the burner system lowers the
efficiency of the system. For additional information on
taking O2readings on the TJSR please contact Eclipse.
Step 8: Set Low Fire Gas
1. Drive the system to low fire.
2. Verify the burner lights reliably at low fire and has a
good flame signal. Monitor the furnace’s ability to hold
temperatures as desired and adjust accordingly.
NOTE: Turndown can be increased by turning the ratio
regulator adjusting screw counterclockwise.
NOTE: It may be necessary to rely on visual inspection.
This is especially true when gas turndowns in excess of
10 to 1 are being used. The main intent is to provide a
clean stable flame with a good flame signal that will not
cause the furnace temperature to overshoot the set point.
Step 9: Verify the Gas Settings
Make sure that all settings are still the same after cycling
the system several times between high and low fire.
NOTE: When all the settings have been completed, mark
the position of the indicator on the butterfly valves to
indicate valve position.
WARNING

15
Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
Step 10: Normal Operation (Post
Commissioning)
Start Procedure
1. Start the blower.
2. Open all the gas cocks.
3. Start the ignition sequence.
4. Verify that flame is present at each burner.
■If a burner does not light, and the system does not
shut down automatically, then you must close the
main gas cock. An uncontrolled flow of gas can
cause fires and explosions.
■Do not touch the ignition plug or the ignition wire
when the ignition is on. You will get a shock.
Stop Procedure
1. Close the following valves:
• The manual gas cock for each burner or zone
• The manual gas cock at the main control valve
• All the manual shut-off valves in the gas line
upstream of the burner gas cock
2. Let the burners cool down. Keep the blower on until
the chamber temperature is less than 1000°F (500°C)
and then stop the blower.
NOTE: Keeping the blower on after the burner is off
protects the burner and the components from hot gases
that flow back through the burner.
DANGER

16 Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
Maintenance &
Troubleshooting
Introduction
This section is divided into two parts:
• The first part describes the maintenance
procedures.
• The second part helps identify problems that may
occur, and gives advice on how to solve these
problems.
Maintenance
Preventive maintenance is the key to a reliable, safe and
efficient system. The core of any preventive maintenance
program is a list of periodic tasks.
Following are suggestions for a monthly list and a yearly
list.
NOTE: The monthly list and the yearly list are an average
interval. If your environment is dirty, then the intervals may
be shorter. Other standards may take precedence for your
particular application.
Monthly Checklist
1. Inspect flame-sensing & ignition devices for good
condition and cleanliness.
2. Check for proper inlet air:gas ratios
3. Check exhaust temperature
4. Test all the alarm systems for proper signals
5. Check ignition spark plugs
6. Check valve motors and control valves for free,
smooth action and adjustment
7. Check for proper operation of the ventilating
equipment
8. Test the interlock sequence of all safety equipment;
manually make each interlock fail, noting that
related equipment closes or stops as specified by
the manufacturer
9. Test flame monitoring control system by manually
shutting off gas to the burner
10. Test main fuel hand-valves for operation
11. Clean or replace the combustion air blower filter
Yearly Checklist
Perform all monthly checklists plus:
1. Leak test shut-off valves for tightness of closure
2. Test air pressure switch settings by checking switch
movements against pressure settings and
comparing with actual impulse pressure
3. Visually check ignition cable and connectors
4. Inspect impulse piping for leaks
5. Remove, clean and inspect all the burners
6. Make sure that the following components are not
damaged or distorted
• the burner nozzle
• the spark plugs
• the flame sensors
• the combustor
• the recuperation tube
7. If applicable, remove and clean all the orifice plates
8. Clean gap in eductor assembly
5

17
Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
Troubleshooting Guide
Problem Possible Cause Solution
Cannot initiate start sequence Main power is off Make sure power is on to control
system.
No power to control Call qualified electrician to investigate.
Air pressure switch has not made
contact
Check air-pressure switch adjustment.
Check air filter.
Check blower rotation.
Check outlet pressure from blower.
High gas pressure switch has tripped Check incoming gas pressure.
Adjust gas pressure if necessary.
Check pressure switch setting and
operation.
Malfunction of flame monitoring control
system such as shorted out flame
sensor or electrical noise in the sensor
line
Have a qualified electrician investigate
and rectify.
Purge cycle not completed Check flame monitoring control
system, purge timer, interlocks and
limit switches.
Start-up sequence runs but burner
does not light
No ignition:
• There is no power to the ignition
transformer
Restore power to the ignition
transformer.
Check flame monitor controller.
No ignition:
• Open circuit between the ignition
transformer and the spark plug
Repair or replace the wiring and
connectors to the spark plug.
Check ground connection to the
transformer.
No ignition:
• The spark plug needs cleaning
Clean the spark plug.
No ignition:
• The spark plug is not correctly
grounded to the burner
Clean the threads of the spark plug
and the burner.
Do not apply grease to the thread of
the spark plug.
Too much gas:
• Improper gas valve train sequence
Verify solenoid valve is down stream
of proportionator.
Too much gas:
• Manual gas butterfly valves have
been opened too far
Check pressures and settings against
startup report and adjust as
necessary.
Too much gas:
• Gas pressure out of the main gas
pressure regulator is too high
Check startup setting and, if
necessary, remove regulator and
investigate.
Not enough gas:
• The gas pressure out of the main gas
pressure regulator is too low.
Check startup settings, then check
regulator and adjust if necessary.
Not enough gas:
• Start gas solenoid valve does not
open
Check solenoid valve coil for proper
operation. Replace if necessary.

18 Eclipse ThermJet Self-Recuperative, V5, Installation Guide 208, 2/4/2013
Start-up sequence runs but burner
does not light, continued
Not enough gas:
• Gas valve not open
Check wiring to the automatic gas
shutoff valve.
Not enough gas:
• Air in the gas line
Check output from the flame safeguard
then open the gas cock and purge the
gas line.
The low fire flame is weak or unstable • Low fire adjusted too low Increase low fire gas setting.
• Not enough gas Check gas adjustment and modify to
increase gas flow.
• Not enough air Check air adjustment.
Investigate any change, i.e. blocked
filter, loose connections.
Increase air supply piping.
The burner goes off when it cycles to
high fire
• Insufficient air (flame too rich) Check air adjustment
Check air filter, clean or replace if
required
The burner is erratic and does not
respond to adjustment
• Flame signal weak Check condition of flame monitoring
device.
• Internal damage to the burner. Some
parts inside the burner may be loose or
dirty
Contact your Eclipse Combustion
representative or the Eclipse factory.
The burner is unstable or produces
soot or smoke
• The air/gas ratio is out of adjustment Measure all the gas pressures and air
pressures, then compare to initial
startup settings and adjust where
necessary.
Cannot achieve full capacity • Air filter is blocked Clean or replace the air filter.
• Gas pressure is too low into the main
gas pressure regulator
Adjust gas pressure.
• Increased furnace/chamber pressure Re-check setup pressures.
• Poor piping practices Contact factory
Cannot achieve efficiency • Too much eductor flow Adjust eductor.
Furnace not balanced • Eductor is not adjusted properly Re-check setup.
• Insufficient pressure to eductor Check piping practices and blower
sizing.
Problem Possible Cause Solution

i
Conversion Factors
Metric to English
Metric to Metric
English to Metric
From To Multiply By
actual cubic meter/h (am³/h) actual cubic foot/h (acfh) 35.31
normal cubic meter/h (Nm³/h) standard cubic foot /h (scfh) 38.04
degrees Celsius (°C) degrees Fahrenheit (°F) (°C x 9/5) + 32
kilogram (kg) pound (lb) 2.205
kilowatt (kW) Btu/h 3415
meter (m) foot (ft) 3.281
millibar (mbar) inches water column (“w.c.) 0.402
millibar (mbar) pounds/sq in (psi) 14.5 x 10-3
millimeter (mm) inch (in) 3.94 x 10-2
MJ/Nm³ Btu/ft³ (standard) 26.86
From To Multiply By
kiloPascals (kPa) millibar (mbar) 10
meter (m) millimeter (mm) 1000
millibar (mbar) kiloPascals (kPa) 0.1
millimeter (mm) meter (m) 0.001
From To Multiply By
actual cubic foot/h (acfh) actual cubic meter/h (am³/h) 2.832 x 10-2
standard cubic foot /h (scfh) normal cubic meter/h (Nm³/h) 2.629 x 10-2
degrees Fahrenheit (°F) degrees Celsius (°C) (°F - 32) x 5/9
pound (lb) kilogram (kg) 0.454
Btu/h kilowatt (kW) 0.293 x 10-3
foot (ft) meter (m) 0.3048
inches water column (“w.c.) millibar (mbar) 2.489
pounds/sq in (psi) millibar (mbar) 68.95
inch (in) millimeter (mm) 25.4
Btu/ft³ (standard) MJ/Nm³ 37.2 x 10-3
Appendix

Installation Guide 208, 2/4/2013