Eco SR30V User manual

05-19-2011
INSTALLATION GUIDE
For Technical Assistance call 1 877 629-8202
NEXT GENERATION™ Recyclers
SR30V & SR60V
Innovation and Leading Technology

Installation guide SR30V & SR60V
2
05-19-2011
Innovation and Leading Technology
Tools required ___________________________________________________________ 3
Parts required ___________________________________________________________ 3
Un-packaging the unit ____________________________________________________ 3
TABLE OF CONTENTS Page
SECTION 1
How to install a Solvent Saver™ Recycler _____________________________________ 4
Installing the Ground wire _________________________________________________ 4
Electrical connection ______________________________________________________ 4
General Arrangement _____________________________________________________ 5-6
Warranty & Contact Information ____________________________________________ 7
SECTION 2
FINAL SECTION

Installation guide SR30V & SR60V
Innovation and Leading Technology Innovation and Leading Technology
3
05-19-2011
SECTION 1
TOOLS REQUIRED
Phillips Screw Driver for all Screws on The Unit Flat Screw Driv-
er or Snips for Removal of Staples Robertson Square Screw
Driver for Pallet Screws Teon
Tape Adjustable Wrench.
PARTS REQUIRED
•Hose and Fittings for connection to Regulator
•Disconnect per classication area (See General
Arrangement Drawings)
-220 Volt 1 Phase Power
-5 - 6 Ft from units at least
-18” above the ground
•Compressed Air Line next to unit
UNPACKAGING THE UNIT
Step 1 : Carefully inspect the shipping carton for any signs of
transport damage.
Step 2 : Begin by removing the staples attaching the box to
the skid (A Flat Screw Driver or Snips will do the job).
Step 3 : Carefully remove your solvent recycler from the
shipping carton. Remove the four screws from the bottom of
the solvent recycler screwed to the palette.
Step 4 : Remove the unit from the palette and place it in the
general area for installation.
You are ready to begin with the installation of the solvent
recycler.

Installation guide SR30V & SR60V
4
05-19-2011
Innovation and Leading Technology
ELECTRICAL CONNECTION
Step 5 : Now we are ready to have the electrician wire the solvent recycler
for model SR30 connect to 220 volts / 1 phase power to the electrical
junction box 1 that is provided in the back of the unit. The 7.5 gallons
recycler requires 15 Amp service.
For model SR60 connect to 220 volts / 1 phase power to the electrical
junction box that is provided in the back of the unit. The 15 gallons
recycler requires 30 Amp service.
Then connect a ground wire 2to the back of the unit ans use the
ground wire with a clip to ground the 55 gallons drum.
For units that come with the optional used solvent ll pump you will
need to connect with an ½ air line to the pump and suggest to put a lter
regulator before the air inlet of the pump and then adjust the air pressure
on the regulator to 80 PSI.
VACUUM INSTALLATION
1. Install the ¼ push in fitting
2. Install the air regulator
3. Install the clear tube coming from the recycler.
4. Install the vacuum generator assembly on the
tank and then connect the cleat tube coming from
the bottom of the tank.
5. Install the blue tube on the 2 push in fittings.
Note : Please Review the “General Arrangement” Drawing .
MAKE SURE ALL CODE REQUIREMENTS ARE FOLLOWED .
You are now ready to follow the Start-up Process.
Please follow the ECO Start-up
2
1
1
3
3
5
5
4
4
2
2
1SECTION 2

Installation guide SR30V & SR60V
Innovation and Leading Technology Innovation and Leading Technology
5
05-19-2011
FINAL SECTION
General arrangement
SECTION 2
GENERAL ARRANGE-
Classication zones as per : A ) NFPA 33 standard for spray application using ammmable and combustible materials, sections 4.3.5 B) International re code, chapter 34 ammable and combustible liquids 3403.1.1 Zone requirements apply to both gun cleaners and recyclers together and stand alone.
EXCLUSIVE RIGHTS
This drawing is the exclusive property of ECO inc. and informations contained herein can be used only when specifically authorized by ECO inc. Possession of this drawing does not authorize use nor transmission to any other organisation.
Intermediate mix room
Legend
Three sides mix room Free standing mix room
Entire system out-
side
Entire system inside
mix room
Class 1 - Div 1 Class 1 - Div 2 Class 1 - Div 2 18’’ High only
4160 Industriel Blvd. Laval, Quebec, H7L 6H1
Tel.: [phone] Fax : [phone]