Ecoboil EBE User manual

Water boilers |Water chillers |Boil/Hot units |Boil/Hot/Chill units |Parts & Accessories
EBC Fusion Series
Automatic Under Bench Boiling & Chilled Water
Installation and maintenance instructions
Please read prior to installation
Important
This unit must be installed by an authorised plumber
The unit to be connected in accordance with AS 3500.4.1
or AS/NZS 3500.4.2
Do not turn on power to these units until water is flowing
from the tap
Please leave these instructions with the owner
WHAT’S IN EACH BOX:
BOX 1: BOX 2:
1 x EBE Boiling Unit 1 x EC 30 Arctic Chiller Unit
1 x EB WP30 Fusion Boil/Chill Tap 2 x EB 400 JG Connector
1 x UBFKI 10B Filter Kit
1 x EB FM 350 kPa PLV
1 x EB 316 Brass fitting kit
1 x Boiling Water Warning Label

Prior to installation
• Flush main water supply inlet line prior to making connections.
• Only teflon tape to be used where necessary, under no circumstances is
plumbing paste to be used.
• When fitting this unit in a cupboard of small proportions, please note that the
unit does omit heat. We recommend a vent is fitted.
• Do not connect to the boiler unit to the hot water line or the fire hydrant supply,
to do so will void the warranty.
• Requires 2 x 3 pin 10 amp power sockets.
Product Information
The boil unit is fitted with a computerised element and boil dry protection. The
computer is set at 95 Degrees C, altitude will alter the boiling point.
• The 350 kPa Pressure Limiting Valve supplied must be fitted.
• We recommend changing the water filter cartridge every 12 months.
• We recommend the cleaning and servicing of the units every 24 months, or
every 12 months in hard water areas.
• If the supplied power cord is damaged it must be replaced by an electrician
• This configuration requires Minimum Inlet Pressure 260 kPa.
Installation Instructions
1. Do not plug in the units or turn on the power until the installation
process is complete.
2. Position the Fusion Boil & Chill tap at the rear of the sink in a workable
location relative to the mixer. Cut a 38mm hole to facilitate mounting
of the tap. Secure the tap by tightening the bracket securing nuts supplied.
3. Position the Boil unit underneath the sink in a position that does not
require extensions to be made in the installation hoses that are
permanently affixed to the bottom of the Fusion Boil & Chill Dispenser
Tap. The Boil unit hoses may be cut to fit, but never extended.
4. Position the Chiller unit underneath the sink so that the chiller air-intake
is as close as possible to the front of the cupboard. The cupboard floor
which extends past the toe-board must have a slot cut into it to provide the
necessary ventilation (pref at least 20mm wide by 3/4 the width of the
cupboard door). The white inlet and outlet hoses from the Boil & Chill
Dispenser Tap can be extended in length if necessary.
5. Secure the 10” Filter with the bracket and screws provided to the
cupboard wall in a handy position relative to the mains inlet line as shown,
taking careful note of which ports are Outlet and Inlet
6. The filter cartridge comes with quick fit John Guest connections, push
the correct inlet/outlet tubes ends into the fittings and pull back carefully
to secure.

7. Connect the hoses on the Fusion Tap to the units as follows:
The three hoses taped together are all inlet hoses, one white, one blue and
one black, ensure these are connected first.
a. 1/4” Blue hose: connect to Outlet port of Water Filter. Using extra blue hose
provided, connect the Inlet Port of the Water Filter to the outlet port of the
PLV via the brass adaptor supplied.
b. 1/4” Black hose connect to the 1/4” brass connector on the top of the Boil
Unit marked “Inlet”.
c. 1/4” White hose: connect to the 1/4” quick fit connector on top of the Chiller
Unit marked “Inlet”.
Then connect the following hoses:
d. 5/16” Copper Pipe: connect to the 5/16” brass connector on top of the Boil
Unit marked “Outlet”.
e. 1/4” Orange silicon hose: push-fit over the end of the extended copper pipe
marked “Vent” on Boil Unit.
f. 1/4” White hose: connect to the 1/4” quick fit connector on top of the Chiller
Unit marked “Outlet”.
Cut or extend all chiller hoses as necessary. Never install with sharp bends,
use a John Guest elbow if necessary.
8. Connect the mains water supply to the inlet port of the PLV using the
15mm Hex nipple and Crox nut supplied.
9. Connect the drain clamp supplied and fix to the waste S bend above the
water level using the rubber seal between the clamp and the waste pipe.
Push on the Opaque silicon tube.
To mains
water supply

Trouble Shooting
SYMPTOM CAUSES ACTION
Water Overflowing
from tap Spout
Expansion chamber full
Low Inlet Pressure
Run Tap for 5-10 minutes
Contact water supplier
Excessive Steam
from tap
Faulty Element Replace element
Water not hot No power supply
Faulty element
Check and test power supply
Replace element
Water not cold No power supply Check and test power supply
No water Water has been turned off
Blocked filter
Check Mains water supply
Clean or replace filter cartridge
Water boilers |Water chillers |Boil/Hot units |Boil/Hot/Chill units |Parts & Accessories
For more information about Ecoboil and our products,
visit our website or contact us:
Ecoboil Appliances Limited
Phone [phone]
Fax [phone]
Mail P.O. Box 940, Pukekohe 2340
Web www.ecoboil.co.nz
10. Open water supply and turn on both Boiling & Chilled Water levers at
the Fusion boil/chill tap until water flows without air bubbles.
11. Plug both units into power points and switch on, allow 20 minutes
prior to testing and use.
12. Check for leaks at all connections and tighten if necessary.
13. Position ‘Caution Boiling Water’ label close to the tap to alert users to
take care when using the hot tap.