Econoco MBSLD User manual

1X
CASTER WRENCH
INCLUDED HARDWARE
MOBILE SOCIAL
DISTANCING SHIELDS
Item # MBSLD, MBSLDO
6X
1/4-20 x 1.5" LONG
LOW PROFILE SOCKET
HEAD CAP SCREW
4X
5/16-18 x 1" LONG
CSK SOCKET HEAD
CAP SCREW
4X
1/4-20 x 0.5" LONG
LOW PROFILE SOCKET
HEAD CAP SCREW
2X
ALLEN KEY
2 PEOPLE
NEEDED FOR
ASSEMBLY
3X
1/4 SPRING LOCK
WASHER
Item # MBSLD, MBSLDO
SHEET 1 OF 6
Item # MBSLD, MBSLDO

U CHANNEL
SIDE - TOP
SIDE - BOTTOM
SIDE - BASE
B
A
4X
4X
LOCKING
CASTER
NON-LOCKING
CASTER
NON-LOCKING
CASTER
LOCKING
CASTER
HOOK
BELT LOOP
2
A. ASSEMBLE THE SIDE-BOTTOM WITH BASE.
B. ASSEMBLE THE SIDE-BOTTOM WITH SIDE-TOP.
NOTE: WHEN ASSEMBLING BASE TO SIDE-BOTTOM, THE BENT LEGS
SHOULD FACE THE SAME DIRECTION AS THE U CHANNEL.
REPEAT FOR SECOND SET OF SIDE PIECES.
1
USE INCLUDED CASTER WRENCH TO ASSEMBLE THE SIDE-BASES WITH
CASTERS.
A. ASSEMBLE THE BASE WITH BELT LOOP WITH CASTERS.
B. ASSEMBLE THE BASE WITH HOOK WITH CASTERS.
NOTE:
PUT THE NON-LOCKING/ LOCKING CASTERS AS SHOWN.
B
A
Item # MBSLD, MBSLDO
SHEET 2 OF 6
Item # MBSLD, MBSLDO

BOTTOM CROSSBAR
U CHANNEL
MIDDLE UPRIGHT
2X
1/4-20 x 1.5" LONG
LOW PROFILE SOCKET
HEAD CAP SCREW
3
ASSEMBLE (2) SIDES WITH
BOTTOM CROSSBAR. MAKE SURE
U CHANNEL
IS FACING UP.
4
ASSEMBLE MIDDLE UPRIGHT.
1X
1/4-20 x 1.5" LONG
LOW PROFILE SOCKET
HEAD CAP SCREW
Item # MBSLD, MBSLDO
SHEET 3 OF 6
Item # MBSLD, MBSLDO

PANEL
PANEL
SIDE BASE WITH HOOK IS ON TOP.
6
CAREFULLY SLIDE TOP PANEL INTO RACK.
TAKE CARE NOT TO BEND THE ACRYLIC WHEN SLIDING IN ACRYLIC PANEL.
5
TIP UNIT ON ITS SIDE.
MAKE SURE THE SIDE-BASE WITH HOOK IS FACING UPWARDS.
CAREFULLY SLIDE BOTTOM PANEL INTO RACK.
TAKE CARE NOT TO BEND THE ACRYLIC WHEN SLIDING IN ACRYLIC PANEL.
Item # MBSLD, MBSLDO
SHEET 4 OF 6
Item # MBSLD, MBSLDO

TOP CROSSBAR
LINK PLATE
7
ASSEMBLE TOP CROSSBAR.
HAND TIGHTEN FROM TOP TO BOTTOM.
THEN GO BACK AND FULLY TIGHTEN WITH ALLEN KEYS.
3X
1/4-20 x 1.5" LONG
LOW PROFILE SOCKET
HEAD CAP SCREW
3X
1/4 SPRING LOCK
WASHER
Item # MBSLD, MBSLDO
SHEET 5 OF 6
Item # MBSLD, MBSLDO

BASE WITH BELT LOOP
BASE WITH HOOK
1
LINK PLATE
2
FOR PUTTING (2) ROLLING
RACKS TOGETHER
1
PUT TWO UNITS SIDE BY SIDE.
MAKE SURE THE BASE WITH BELT LOOP
AND
BASE WITH HOOK
ARE PLACED END TO END.
HOOK THE TWO BASES TOGETHER. LIFT THE
BASE WITH HOOK
AND DROP IT INSIDE THE
BELT LOOP
.
2
UNSCREW THE TOP SCREWS FROM THE
JOINING UNIT. SWING LINK PLATE AND SCREW
IN TO SECURE THE TWO UNITS ON TOP.
Item # MBSLD, MBSLDO
SHEET 6 OF 6
Item # MBSLD, MBSLDO