progressive automations FLt-08 User manual

FLT-08
User Manual
Page 2
Page 3
Page 4
Page 5-6
Caution/Liability
Technical Specifications
Parts
Assembly Instructions
Operational/Reset Procedure,
Troubleshooting
Dimensions
Page 7
Contents
Page 8

Caution
Liability
2

3
Technical Specifications
Base Width 43” min. - 74” max. (55.3" with Cable Tray installed)
Duty Cycle 10% Max. 2 mins on, 18 mins off
Height Range 23.5” - 49” (without table top)
Minimum Table Top Size 43"x 24” (per set)
Weight Capacity 220 lbs per set
Features Soft start/stop, adjustable leveling studs & 4 memory presets
Input Voltage 120 VAC, 60 Hz
Output Voltage 24 VDC
Stroke 25.5"
Speed 1.5"/sec
Material Steel
Certification UL

Parts
4
Side Bracket Frame 1 Center Rail Frame 2
Leg
(Right)
Foot Caster Control Box Beam Screen Holder Cable Tray
Cover
Cable Tray M8x12 Machine
Screw
M6x14 Machine
Screw
M6x10 Machine
Screw
ST5x20 Wood
Screw
St5x116 Wood
Screw
Handset Power Cord Cable Cable Clip
Leg
(Left)

Assembly Instructions
5
STEP 1
Prepare the four legs (5 & 6) as shown in the
picture below.
STEP 2
Using the supplied Allen Wrench, insert four M8x12 Machine
(14) Screws to attach the Beams (10) to the legs as shown in the
picture below.
STEP 3
Use 16 of the M6x10 Machine Screws (16) to attach the
Frames to the Legs. Put the Center Rails (3) into the Frames
as shown in the picture below.
*Please note that while the picture shows the table lift set
flipped over, we do not recommend flipping it until Step 5*
STEP 4
Slide the Side Brackets (1) into the Frames. Use eight of
the M6x14 Screws to attach the Side Brackets to the
Frames.

6
Assembly Instructions
STEP 5 (optional)
Insert four of the M6x10 Machine Screws into the holes of
the Beams then assemble the Cable Tray as shown in the
picture below.
*Please note that once you install the Cable Tray, the base
width will be locked in that position. If you'd like to adjust
the base width, skip to step 7*
STEP 6
Place the Cable Cover Tray (12) on top of the
Cable as shown in the picture below.
STEP 7
Use 24 of the M6x10 Machine Screws to
attach the Center Rails to the Frames and to
attach the Screen Holders (11).
STEP 8
Use the ST5x20 Wood Screws to attach your two
table tops (sold separately) to the assembled table lift
set. Please ensure this is enough space between the
table tops so they do not over lap one another.
STEP 9
Connect the Cables and attach the Hand Remotes
to the table tops. Position them wherever you want.

7
Reset Procedure
Operational Procedure
Once your table lift is installed, operation is simple. Using the wired remote will allow full control over
extending and retracting the lift columns. Use the up button to raise the table lift and the down button
to lower the table lift.
You can program up to 4 locations using the memory setup: Use the up/down buttons on the remote to
find your desired height(s), then press “M” followed by a number 1-4. The table height position is now
saved. To move to the set position, hold the number button.
IMPORTANT
You must reset the desk prior to use:
To reset, press and hold the DOWN button on the Hand Remote (7) until the table lift reaches its
lowest point. Release the DOWN button. Press and hold the DOWN button again until the LED display
shows "RST". If you are not using an LED hand remote hold it for about 10 seconds. Release the
DOWN button. Finally press and hold the DOWN button once more until the table lift lowers, slightly
rises then stops. This signals the end of the reset procedure. Release the DOWN button and your table
lift is now ready to use.
Troubleshooting
If your desk is not functioning it might need to be reset. Follow the RESET procedure.
If your hand remote has an LED display and it displays "RST" (reset), perform the reset procedure.
If the LED displays shows an error message ("Er1" - "Er13"), confirm that all wired connections are
secure. Then perform the reset procedure.
If the LED remote displays "HOT", let the unit cool down for 20 minutes.
If the error message persists after the reset procedure, contact us at 1-800-676-6123 or
[email protected].

Dimensions
8
34.4"
23.5"
25.5"
55.3" with Cable Tray