EcoReco M series User manual

PERSONAL MOBILITY REDEFINED
M SERIES OWNER’S MANUAL

CONTENTS
INTRODUCTION
GENERAL GUIDANCE
EcoReco SCOOTER COMPONENTS
RECHARGEABLE BATTERY AND CHARGER
DASHBOARD AND THROTTLE UNIT
BRAKE
TECHNICAL SPECIFICATIONS
EcoReco SCOOTER OPERATION
SAFETY REQUIREMENTS AND CHECKS BEFORE OPERATION
UNFOLDING FOR OPERATION
OPERATING TIPS
FOLDING FOR TRANSPORT/STORAGE
TOP SPEED CONFIGURATION
CLEANING AND SERVICING
LIMITED MANUFACTURER WARRANTY
NOT INCLUDED IN THE WARRANTY
OTHER DISCLAIMERS
DECLARATION OF CONFORMITY
1
2
3
4
7
8
9
10
10
11
13
14
17
18
19
20
21
22

INTRODUCTION
[e-mail]
1608 W Campbell Ave, #280
Campbell, CA 95008, U.S.A.
Welcome to the EcoReco community!
Thank you for choosing an EcoReco electric scooter for your eco-friendly recreation and commuting.
You will soon experience first-hand that the EcoReco scooter is a compact, efficient, and economic
personal transportation vehicle.
This manual provides an overview of the function, operation, maintenance and warranty of your new
scooter. Please read the instructions carefully to help ensure that you ride safely and your electric
scooter has a long service life.
Always follow state regulations and traffic rules regarding the operation of your electric scooter.
Always wear a safety helmet and suitable clothing, pads, and shoes, and maintain full control of
the scooter at all times while riding.
Observe the battery’s charging requirements to avoid damaging the scooter and to significantly
extend its service life.
The information in this manual is accurate at the time of printing. Visit our official website at
ecorecoscooter.com for the latest version of the owner’s manual as well as a list of authorized repair
shops and dealers.
Please register your scooter at ecorecoscooter.com to activate personalized services and timely
technical supports. Please do not hesitate to contact us if you have any questions:
Enjoy your new EcoReco ride!
ECORECOSCOOTER.COM
1

GENERAL GUIDANCE
The EcoReco scooter is delivered fully assembled from the manufacturer.
The battery is pre-charged to 50% out of box for your convenience.
The EcoReco scooter undergoes several test rides and charge cycles at the factory for quality assurance
purposes. The dashboard might display a few charging cycles and miles ridden at the date of receipt.
The product serial number(S/N) is located under the scooter chassis. It is also recorded on the back of this
owner’s manual for future service reference.
The scooter is designed for operation by and the transport of only one responsible person age 16 or older.
Adult supervision is required during charging and operation of the scooter.
Your insurance may not cover accidents involving the scooter. Contact your insurance company for more
information.
Consult your state’s transportation authorities for the latest regulations before operating the scooter on
streets. The scooter can only be used on private property UNLESS it is street legal in the state in which you
intend to operate it. (While federal and many state laws approve its legal use in bike lanes, some states
consider a motorized scooter not street legal.)
Your scooter is suitable only for flat surfaces, not for open country, hills, or potholes. Observe road
conditions and follow traffic rules at all times.
Do not operate your scooter on wet surfaces or in bad weathers.
For your safety, do not jump or perform stunts while riding. Doing so may also reduce the product life due to a
higher load on folding mechanisms and delicate electronics inside.
Fully charge your scooter if you plan to store your scooter for a long period of time.
During long storage periods, monitor the battery level at least once every 3 months. Recharge the battery if
the level is low. The battery naturally discharges over time. Deep discharge could cause irreparable damage
to the battery.
Non-designated use of the scooter will cause the warranty to become void.
All modifications to increase performance/speed or generally alter the fundamental features of the scooter
endanger the operational safety while reducing the service life of your scooter. Modifications of the scooter
immediately voids the manufacturer warranty. Some modifications may be considered a criminal offense and
be subject to fines or prosecution by law.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
2

13
15
EcoReco E-SCOOTER
Handlebars
Handlebar sleeves
T-bar
Stem
Positioning pin
Dashboard and throttle unit
Brake lever
T-bar tightening knob
Securing latch
Fixing lever
Foot deck
Charging socket
Kickstand
Rear suspension *M5 only
1
2
3
4
5
6
7
8
9
10
11
12
13
1
14
14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Rear wheelbrake
15
3

1 2 31 2 3
RECHARGEABLE BATTERY
AND CHARGER
BATTERY CONDITIONING
CHARGING THE BATTERY
The battery in your EcoReco scooter is state-of-the-art rechargeable Lithium FerroPhosphate (LiFePO4, or Li-Iron). It
is the most suitable material and advanced battery type for personal transport applications. it is significantly lighter
and smaller, and provides a longer life than an outdated, toxic Sealed Lead Acid battery. It also is inherently safer
and more environmentally friendly than a Li-Ion battery.
The EcoReco battery is pre-charged to 50% out of box for your convenience so you can ride it right away.
Use the EcoReco charger to recharge the battery when the battery reading on the dashboard is low. The most
efficient zone to charge is in between 1-4 bars. LiFePO4 batteries have no memory effect.
Expect the battery to charge from empty to 80% in 2 hours (recommended) or from empty to full in 4.5 hours.
Ensure the scooter is switched off, then open the end cap on top of the charging socket adjacent to the
kickstand.
Connect the charger circular plug to the scooter’s charging socket, then connect the charger 3 prong plug to the
power outlet.
The battery is charging when the charger LED is red. The charger LED turns green when it's 85% full. You can
continue to charge the scooter and top it off for additional 1-2 hours if needed. To stop charging, please remove
the 3 prong plug from the power outlet, then remove the circular plug from the scooter’s charging socket. Close
the end cap.
1.
2.
3.
4

INSPECTIONS AND REPAIRS
BATTERY STATUS
USAGE
Charging safety tips
Use only only the EcoReco branded battery, charger and cables supplied.
Only use EcoReco factory parts.
Ensure the correct connection of the charger using the designated cables.
Ensure sufficient ventilation.
Ensure a dry environment. Never allow the charger or cable to come into contact with water as this may
result in an electric shock. Never touch the charger or cable with wet hands.
Immediately remove the plug from the electrical outlet if any fault arises during charging.
Always pull the plug, not the cable.
Do not allow the charger or cables to be damaged or crushed by sharp edges or heat.
Be careful when charging the scooter in the folded position. The weight of the scooter may damage the
charging connector if the scooter falls on the cable connector.
Before each charging, perform regular visual inspections of the cables and charger.
Do not operate the charger if the charger or cables displays visible damages.
Contact EcoReco to order a replacement charger. A damaged charger could cause personal injury or short
circuit the scooter electronics, voiding the warranty.
Do not carry out independent repairs on the battery, charger or cables. Contact EcoReco or your dealer for your
service needs.
The battery capacity status and charging cycle are indicated on the dashboard when the scooter is powered on.
More information is outlined in the “Dashboard and throttle unit” section.
It is most energy efficient when charging is performed between 20-80% of battery capacity.
When used normally, the battery should not lose more than 20% of its capacity within the first 600 charging
cycles. Typical rechargeable cycles of Lithium FerroPhosphate (LiFePO4) are more than 2,000 times without
losing significiant capacity.
If you ride until the battery is fully discharged and the scooter shuts down automatically, it will not cause any
damage. However, please charge the battery immediately.
Please do not force to restart the dashboard and throttle unit after the battery is fully discharged and the
scooter shuts off automatically. Doing so might cause irreparable damage (ie, deep discharge) to the battery
and also cause the warranty to become null and void.
Avoid operating the scooter when the battery is hot.
5

STORAGE
Important
Avoid storing the scooter under direct sunlight (even if it’s inside your car trunk) for a long period of time. The
temperature of the scooter body and battery could reach higher than 110 degrees Fahrenheit, causing damage
to the functionality and product lifetime of the battery.
Avoid storing the scooter in wet environments.
Batteries self-discharge slightly everyday even when not in use. Longer storage periods without charging incur
irreparable damage (ie, deep discharge) to the battery. Therefore, charge the battery regularly.
In winter, the battery can lose capacity faster because of low temperatures.
Recharge the battery in full immediately after it has completely discharged or before storing the scooter for
longer periods.
Even in storage, please monitor the battery level and recharge the battery fully at least once every 3 months.
Please charge your EcoReco scooter in full before storing it for long periods.
Avoid storing the scooter under direct sunlight or in wet environments.
Even when it is not in use, monitor the battery status or recharge your EcoReco scooter fully every 3
months to prevent a self-induced deep discharge.
6

Throttle lever
Power button
Mode Selection button
Speedometer
Battery status
DASHBOARD AND THROTTLE UNIT
1.
2.
3.
4.
5.
Note
Warning
Throttle lever:
The scooter is equipped with Safe-Start protection to
limit uninrended jerking; you must first “roll” the
scooter manually to gain initial speed before the
throttle lever becomes activated. Place your finger(s)
over the throttle lever and squeeze as desired to
accelerate.
Power button:
Press for about 2 seconds to power on and about 1 second to power off.
Mode selection button:
Press the “mode” button as needed to switch among the following functions in sequence.
(a) TRIP: Distance traveled since last resetting the display.
(To reset, hold down the “mode” button until the display flashes twice.)
(b) ODO: Odometer to show total distance traveled.
(c) Numerical Speedometer: (Current velocity of the scooter, it shows “0” when standstill)
(d) Charging Cycle Counter.
There are total 5 bars indicating the current battery level. Each represents 16% of battery capacity.
When the battery level indicator is flashing and shows zero bars, the battery level is low (16% capacity
left). You can continue to operate the scooter for some time, but should charge it soon.
The dashboard unit would shut down automatically when the battery drains below 3% to prevent from
deep discharging .
Speedometer:
Graphic bars display the current speed in miles per hour (mph).
For quality assurance, an EcoReco scooter must go through several test rides and charging cycles.
Therefore, the 0D0 and Charging Counter modes might display miles ridden and charging cycles upon
receipt.
Press and hold the “mode” button at the cycle counter mode to change the unit system from imperial to
metric. A blinking “SET” and 001 indicates the unit is miles per hour (mph). Click the “mode” button
again can switch to kilometers per hour (KPH) (000). Holding the mode button for 3 more seconds sets it.
After emergent stops, it takes about 1-2 seconds to re-calibrate the zero
speed. The Safe-Start feature does not kick-in during this period, so you
may still accelerate the scooter if pulling the trigger. Please make sure
the scooter completely stops for more than few secs, if you would like
the Safe-Start feature to function again.
Battery status: miles per hour (mph).
7

Drum brake
Brake wire
Screw
Brake lever
Moisture can cause the brake to react more slowly. For this reason:
“Dry brake” carefully in a safe place after washing the scooter.
Avoid operating the scooter in bad weather (such as rain, snow, or
ice).
When taking a longer journey in the rain is unavoidable, reduce speed
and increase the braking distance. Carefully and slowly pump the
brake to avoid losing control of the scooter. Use caution when crossing
painted lines on bike trails or roads. The surface may be slippery and
cause a loss of control.
BRAKE
Warning
BRAKE ADJUSTMENT
The brake lever for the rear wheel brake is on the left handlebar.
To slow down or stop the scooter when it is powered on and moving,
squeeze the brake lever.
The drum brake on the rear wheel does not kick in until after the brake
lever is fully pressed.
As soon as the brake is activated, the accelerator lever on the right
handlebar is deactivated.
To adjust the brake tightness, slightly rotate the screw along the brake
cable near the bottom of the stem. Test the brake effectiveness multiple
times before riding for distances again.
To adjust the brake, open the cable wrap.
Adjust the screw accordingly and test ride to confirm result.
Cover cable wrap back to the wire.
8

Charging time 2 hrs(80%) to 4.5 hrs(100%)*
Load maximum 260 lb
Total weight 34 lb
Engine performance 250 W
Battery LiFePO4 36V 8 Ah
Wheel size 6.3 x 1.9 in
Size “upright” (operation mode) 38 x 22 x 46 in
Size “folded” (compact mode) 36.6 x 5.5 x 11.8 in
*After first-time operation.
†Based on product testing statistics under continuous operation of a 170-lb rider on flat
ground at steady speed in a close course.
SPEED AND RANGE ESTIMATES PER CHARGE†
CRUISING
REGULAR
PERFORMANCE
Speed average 8 mph
Range 19 miles
Speed average 13 mph
Range 20 miles
Speed average 18 mph
Range 13 miles
TECHNICAL SPECIFICATIONS
Actual operating mileage depends highly on the rider’s weight and riding style, road
conditions, climate and battery’s condition; therefore, estimation here only serves
as a reference. Actual mileage per charge might vary.
9

EcoReco SCOOTER OPERATION
SAFETY REQUIREMENTS
Reminders about the battery and scooter performance
The EcoReco battery is pre-charged to 50% out of box for your convenience.
Your EcoReco scooter is intended for leisure activities only. Operation of the vehicle on
public roads is subject to the latest regulations of federal and local authorities, and all
offenses against the law could result in penalties.
Always wear a safety helmet and suitable clothing, pads, and shoes. Wear bright,
noticeable colors to ensure others can see you more clearly and quickly.
Your EcoReco scooter is delivered ready for operation from the manufacturer. No further
assembly is needed.
DISPOSAL
Warning
Battery and electric equipment must not be disposed of as household waste.
You are already making a major contribution to environmental protection by riding your EcoReco scooter. To further
avoid unnecessary pollution:
Dispose of your EcoReco scooter and all associated components (such as batteries) through authorized
disposal facilities.
Please observe the most recent applicable guidelines. If in doubt, find out about environmentally friendly
guidelines from your disposal facility.
If your scooter significantly fails to reach full speed or range during operation although the battery has
been fully charged, this could be attributable to unusual use of your scooter or a defect of the battery.
Please contact our customer support team or an authorized dealer.
Extreme temperatures, steep inclines. high loads, older batteries and longer storage periods without
charging can significantly impact performance.
10

3
UNFOLDING FOR OPERATION
Refer to the “EcoReco scooter components” section if needed.
1
2
Press down the fixing lever, and lift up the stem from the deck
unitl it clicks into place.
Lift up the securing lever and secure it against the stem.
Expand the handlebars until the handlebar sleeves click into
place. (Be careful not to wrap the handlebar wires around the
dashboard unit.)
11

6
5
4
Fail to tighten the knob might result in unintented stress on the
positioning pin and failure to hold the handlebar height during
operation.
Warning
FINAL SAFETY CHECKS BEFORE OPERATION
Loosen the T-bar tightening knob.
Pull out the T-bar extension and lock it into position (with
the positioning pin) at the preferred height.
Because transport and longer periods of non-usage can incur defects that impair the
scooter’s function, check the following before operation each time:
The brake functions.
The folding mechanism is secured. the securing lever is up and closed.
The battery level is sufficient.
The tires are not damaged.
T-bar tightening knob is tightened.
Tighten the T-bar tightening knob.
12

Warning
Always inspect the scooter for roadworthiness before use.
After some time of usage, the securing latch might become loose and pop up during operation, which would
put unintended stress on other parts of the folding structure and cause damages. To adjust the tightness,
please access from the bottom of the folding assembly and use a socket wrench to tighten the adjustment
nut until the latch can hold its right position during operations.
Find a private area without road traffic and with enough space for you to get used to your
EcoReco scooter.
Note that the T-bar height might feel differently once you step on the deck. Readjust it if needed
and make sure to tighten the T-bar tightening knob.
Lift up the kickstand.
If riding your EcoReco scooter for the first time, familiarize yourself with its movement and
balance by"rolling" it without the power on: Depending on the stance you prefer, put your
dominant leg on the front of the deck and the other one on the ground. with your head
facing forward. Use the leg on the ground to push the scooter forward. Once you gain some
speed. gently lift up that leg and rest it on the back of the deck. If needed, adjust your grip
on the handlebars to remain balanced. Repeat the same movements once the scooter
slows down to keep it going.
Riding the scooter without power does not damage it.
Do not turn on the power until you feel confident“rolling”.
Press the EcoReco power button on the dashboard for 2 seconds until the display lights up.
The scooter is now ready for you to get on and take off.
Your EcoReco scooter offers Safe-Start protection to limit
unintended jerking. This means you must first roll the
soooter manually for an initial speed before the throttle
lever becomes activated. Place your finger(s) over the
throttle lever and push in as desired to accelerate.
When the brake is activated, the throttle is deactivated.
See the “Brake” section for guidance on the brake and brake
lever.
A slight whirring sound is normal when the scooter is
powered on and moving.
To preserve the battery, press the power button to shut off.
the scooter shuts off automatically after 3 minutes of inactivity.
OPERATING TIPS
13

FOLDING FOR TRANSPORT/STORAGE
1
2
3
Turn off the scooter. (The scooter also shuts off automatically
if inactive for 3 minutes.)
Pull the handlebar sleeves away from each other.
Fold down the handlebars.
This section describes how to fold the scooter for transport or storage. Refer to the “EcoReco scooter components”
section if needed. Do not operate the scooter when it is “folded.”
14

6
4
5
Loosen the T-bar tightening knob.
Push in the positioning pin and push the T-bar extension down
into the stem.
Push down the securing latch.
15

7
8
9
Lift the stem, so that the front wheel is slightly off the
ground, then press down the fixing lever.
Fold the stem down to the deck.
To carry the scooter, lift it up by the stem.
16