ecosens ECO-14 User manual

Wall PIR Sensor
ECO-14
Manual
Welcome to use ECO-14 Infrared motion sensor!
The product is a new saving-energy switch, it adopts good sensitivity detector, integrated
circuit. It gathers automatism, convenient safe, saving-energy and practical functions. It utilizes
the infrared energy from human as control-signal source, it can start the load at once when one
enters detection field. It can identify day and night automatically. It is easy to install and used
widely.
SPECIFICATION:
Power Source: 220 -240V/AC Detection Range: 160°
Power Frequency: 50Hz Working Temperature:-20~+40℃
Ambient Light:3-2000LUX(adjustable) Working Humidity:<93%RH
Time-Delay : min:10sec±3sec Installation Height: 1m-1.8m
Max:8min±2min Power Consumption:0.45W (work)
Rated Load: 600W (incandescent lamp) 0.1W (static)
200W(energy-saving lamp) Detection Motion Speed: 0.6-1.5m/s
Detection Distance: 9m max(<24℃)
FUNCTIONS:
Can identify day and night: The consumer can adjust work ambient light. It can work in the
daytime and at night when it is adjusted on the “sun” position (max). It can work in the
ambient light less than 3LUX when it is adjusted on the “moon” position (min). As for the
adjustment pattern, please refer to the testing pattern.
Time-delay is added continually: When it receives the second induction signals after the
first induction, it will compute time once more on the rest of the first time-delay basic.(set
time)
Time-delay adjustment: It can be set according to the consumer’s desire. The minimum
time is 10sec±3sec. The maximum is 8min±2min.
The switch: “ON”、“OFF”、“PIR”.
Good sensitivity Poor sensitivity

o
INSTALLATION: (see the diagram)
Shut off the power.
Loosen the connection column on the bottom of sensor, plug the
wire into connection hole, tighten the screws; unload the surface
of sensor, connect the sensor into connection box.
If you want to install it in quadrate connection box, penetrate
the setscrew into installation hole, aim at the installation hole
on connection box, then tighten the screw; if you want toinstall
it in circular one, you can use the same way as the quadrate,
also adjust the sensor’s position, tighten the setscrew on
surface, then the fixing arm will open automatically, fasten the
connection box.
Switch onthe power then testit.
CONNECTION-WIRE DIAGRAM (see the following Fig)
TEST:
Set the function switch to “ON”, Turn the TIME knob
anti-clockwise on the minimum after taking the
Board-face off. Andturn the LUX knob clockwise on
SUN position (if you test it in daylight).
Switch onthe power, the lamp should beon.
Set the function switch to “OFF”, the lamp should be
off immediately, all functions should be in “stop” state.
Set the function switch to “PIR”, after 30sec later, it enter into working position. The lamp
will be turned on after receiving the inductor signal.20sec. Under no inductor signal
condition, the lamp should be off within 5~10sec.
Set “LUX” anti-clockwise to minimum, after it is off when there is no inductor signal
condition, the lamp should be off in the daytime, but if you use a opaque object to cover
Sensor, the lamp should be on, then off within 5~10sec.
Note: when testing in daylight, please turn LUX knob t (SUN) position, otherwise the
sensor lamp could not work!
NOTES:
Electrician or experienced human can install it.
The unrest objects can’t be regarded the installation basis-face.
There aren’t hinder or unrest objects effecting detection in front of the detection window.
Avoid installing it near temperature alteration zones, for example: air condition, central
heating etc.
Please don’t open the case for your safety if you find the hitch afterinstallation.
If there are some difference between instruction and the function the product has, please
give priority to product and sorry not to inform you additionally.
SOME PROBLEM AND SOLVED WAY :
The load don’t work:
a. check the power and theload.
b. If the load is good.
c. If the indicator lamp is light or not.
d. Please check if the working light corresponds to the ambient-light.
The sensitivity is poor:
a. Please check if infront of the detection window there is hinder that effect to receive
the signals.
b. Please check the ambient temperature.
c. Please check if the signal source is in the detectionfield.
d. Please check the installation height.
e. If the moving orientation iscorrect.
The sensor can’t shut off the load automatically:
a. If there is continual sensor signal in the detection field.
b. If the time-delay be set to thelongest.
c. If the power correspond to theinstruction.
d. If the temperature change near the sensor.Such as air condition, central heating
etc.