EcoSmart Fire BK Series User manual
BK Series AB Series XS Series VB SeriesXL Series
INSTALLATION,
OPERATION
AND MAINTENANCE
MANUAL
! WARNINGS:
IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION
MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
PLEASE READ THESE INSTRUCTIONS COMPLETELY
BEFORE OPERATING THE ECOSMART™ FIRE.
e-NRG bioethanol is the
ONLY fuel to be used in
this appliance.
www.ecosmartre.com © Copyright 2004 - 2016 The Fire Company Pty Ltd. All rights reserved. V0316e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
Contents
Bioethanol replaces are classied by regulations and standards as
decorative replace appliances intended for occasional use only (not
for heating).
EDUCATE ALL USERS
This type of technology is not well known and therefore we
recommend that owners diligently induct any potential user of their
Fire to ensure everyone is aware of the safety procedures associated
when using e-NRG Bioethanol as a fuel source.
Operational Videos and Manuals can be found on our website or by
contacting your local distributor.
WHY REGISTER YOUR WARRANTY?
Registering your warranty achieves more than simply activating your
warranty - it provides our head oce with the information that we
require in order to communicate important safety and regulatory
information to you should the need arise.
This could include things like:
• Prompt notication in the unlikely event of a potential hazard,
• Changes to fuel storage regulations, supply channels or special
oers,
• Reminders about regular safety steps and maintenance procedures,
• New model announcements or accessories that suit or enhance
your purchase.
It is important that we are able to communicate eectively with our
customers as part of our commitment to continual improvement,
consumer safety and property protection.
If you purchased your product through an external distributor, retailer
or agent The Fire Company does not have these details on le and
may have trouble sourcing them as systems and best practices vary
from business to business.
Please register your warranty today. You can do this online at the
following web address: or by
sending through your details via email using the details below.
EcoSmart Fire is designed
and manufactured by The Fire Company
Showrooms 3 & 4, 40-42 O’Riordan Street
Alexandria NSW 2015 Australia
Tel: +61 2 9997 3050
Email: info@ecosmartre.com
Important Safety Information
Standard Equipment Received
Markings
Clearances & Installation
How to Operate the Burner
Regulatory Information for the Safe Handling
and Storage of e-NRG Bioethanol
Decanting your e-NRG Bioethanol
into the Jerry Can
Decanting your e-NRG Bioethanol from the
Jerry Can into the Burner
Lighting the Burner
Regulating the Flame
Baes
Turning your Burner OFF
- Extinguishing the ame
Re-igniting the Burner
Regular Safety Checks
Caring for your EcoSmart Fire
Troubleshooting
Your Warranty
After Sales Service
3 – 4
5 – 7
8
9 – 11
12 – 13
14 – 17
14
14
15
16
16
16
17
17
18
19
20
21
22
e-NRG Bioethanol is the ONLY fuel to be used in this appliance.
FLAMMABLE
You must familiarise yourself and comply with local regulations in
order to safely and legally store, handle, decant and use e-NRG
Bioethanol.
Refer to the e-NRG Safety Data Sheet (SDS) for important Health and
Safety information.
Ethanol, the primary ingredient of e-NRG fuel, presents
reduce the likelihood of ignition are not followed.
These include:
• Permitting for volumes of e-NRG (e.g. for USA, greater than 5 gallons
stored inside, or greater than 10 gallons stored outside).
• Removal of all potential sources of ignition including sparks and
open ames.
• Maintenance of good ventilation of enclosures where e-NRG is stored.
• Storage of e-NRG (e.g. for USA, greater than 10 gallons in an
approved storage cabinet).
• Storage in such a way as to reduce the likelihood of spillage or
container rupture.
• Responsible handling to include:
- Use of the Jerry Can in an approved manner and with attention to
the possible presence of ames or other ignition sources in or near
the
appliance,
- Limiting access to qualied users,
- Proper transfer techniques to limit spillage and generation of
static electric discharge (i.e bonding and grounding),
- Proper labeling and signage in accordance with applicable re codes.
These precautions are necessary to reduce risk of damage to property,
injury and death resulting from accidental ignition of e-NRG.
To order your e-NRG Fuel contact:
Australia
Visit - www.e-NRG.com.au
Call - 1300 003 NRG
USA
Visit - www.e-NRG.com
Call - (888) 670 ENRG
Or contact your local EcoSmart Fire distributor.
www.ecosmartre.com © Copyright 2004 - 2016 The Fire Company Pty Ltd. All rights reserved. V0316e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
Important Safety Information Important Safety Information
Congratulations on your purchase of an EcoSmart™ Fire.
The Fire Company Pty Ltd is very safety conscious. We have taken
every care in designing, manufacturing and assembling your Fire
ask that you exercise care when using this
appliance
and follow the
instructions below:
This manual contains instructions for the safe installation and
use of your new EcoSmart Fire. Before installing and using your
appliance, read the entire manual and follow the instructions and
warnings carefully.
WARNING! Failure to follow these instructions and warnings could
result in death, serious injury, or property damage.
! WARNING
i. Never use any fuel other than e-NRG Bioethanol in the
appliance. Never use gasoline.
iii. Wipe up spills immediately with a dry cloth followed by a cloth
dampened with water. Allow to dry completely before lighting
Burner.
vapors are present.
v. Store fuel only in original container or provided Jerry Can. Store
away from area where the
appliance
store fuel only in a plastic or metal container that is acceptable for
use with the fuel and non red in color.
vi. Never smoke while refueling or lighting the appliance.
2. LOCATING THE FIRE
i. Keep children away from the
appliance
. Never leave children
ii. Install a smoke alarm and test it monthly to make sure it is in
purchased from your distributor or independently.
iii. For decorative purposes only. Not suitable for continuous
operation. Do not use the
appliance
to heat or boil water or as
a cooking appliance. Do not put wood, charcoal, paper or other
combustible objects in the Fire.
3. VENTILATION
i.
pollution. Use only in well-ventilated areas and those that are
ventilation can cause serious injury or death. People with breathing
problems should consult a physician before using the appliance.
Refer to ventilation information on page 12.
4. FUELING THE FIRE
DO NOT FILL WHILE
OPERATING
DO NOT FILL
WHILE HOT
i. This
appliance
ONLY uses e-NRG Bioethanol fuel. e-NRG
or supplied Jerry Can away from heat and sources of ignition.
Refer to page 1 for more information.
standards and rules. You must familiarise yourself with the
appropriate regulations of your country in order to safely and
legally store, handle, decant and use this fuel.
iii. The customer warrants to The Fire Company Pty Ltd that after
delivery of their Fire and whilst The Fire Company Pty Ltd retains
any interest in the goods or consigned goods (as the case
may be) the customer shall comply with all applicable acts,
regulations and laws dealing with the transport, unloading and
storage of dangerous goods.
iv. The Fire Company Pty Ltd is not liable for any damage caused by
using the incorrect type of fuel.
5. OPERATING THE FIRE
ii. Do not use if damaged or malfunctioning.
iii. Risk of explosion or burn. Use only the lighting rod and lighter
provided with your
appliance
matches or other lighters could result in serious injury.
iv. Do not use the lighter without the lighting rod.
v. Remove the Burner frequently to check for any residual fuel
underneath the Burner. Accumulation of fuel underneath could
cause an explosion.
i. Due to high surface temperatures, keep children, pets, clothing
and furniture away from the unit, as the unit is hot while in
operation, contact with the
appliance
may cause skin burns.
during operation and will stay hot for up to 60 minutes after use.
To avoid injury, do not touch with any parts of your body nor
liquids. Always use the lighting rod provided with your
appliance
7. USING ACCESSORIES
i. Use only authorised accessories and tools with your
appliance
.
Accessories and tools supplied by EcoSmart Fire are strongly
recommended. Light only with the lighting rod and lighter
accessories for your
appliance
.
ii. Doors must not be added to modify any EcoSmart Fire model.
appliance
in
iii. EcoSmart Fires have not been tested with an unvented gas log
gas log set into this appliance.
not be placed directly over the Burner mouth or interfere with
the accessories will not explode, emit carbon monoxide or
fumes when exposed to extreme temperature variations.
- Fire accessories must not be smaller than the largest opening
of the burner used so that the accessories cannot fall into the
burner at any time.
injuries to children and pets. The
should never be left
unattended.
If you have any questions regarding any of the above important
safety information please contact your distributor or The Fire
Company Pty Ltd.
Please store these warnings in a safe place for future reference.
www.ecosmartre.com © Copyright 2004 - 2016 The Fire Company Pty Ltd. All rights reserved. V0316e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
Standard Equipment Received Standard Equipment Received
Please ensure that all items have been received. The Burner Range
includes the minimum equipment required to operate the Burner safely.
Burner
The Burner is the core product of the EcoSmart Fire as it is the
chamber that houses the fuel.
BK5
h123mm x l400mm x d317mm
h[4.4in] x l[15.7in] x d[12.5in]
7.3kg [16.1lbs]
BK3
h 93mm x l290mm x d290mm
h[3.7in] x l[11.4in] x d[11.4in]
6.8kg [14.9lbs]
BK2UL
h 93mm x l290mm x d290mm
h[3.7in] x l[11.4in] x d[11.4in]
6.8kg [14.9lbs]
BK SERIES
XL SERIES
XL900
h112mm x l908mm x d195mm
h[4.4in] x l[35.7in] x d[7.7in]
15kg [33.1lbs]
XL500
h112mm x l500mm x d195mm
h[4.4in] x l[19.7in] x d[7.7in]
7.3kg [16.1lbs]
XL700
h112mm x l700mm x d195mm
h[4.4in] x l[27.6in] x d[7.7in]
12kg [26.5lbs]
XS SERIES VB SERIES
XS340
h87.2mm x l340mm x d190mm
h[3.4in] x l[13.4in] x d[7.5in]
3.7kg [8lbs]
VB2
h122mm x l330mm x d110mm
h[4.8in] x l[13.0in] x d[4.3in]
2.1kg [4.6lbs]
AB SERIES
AB8
h156mm x ø360mm
h[6.1in] x ø[14.2in]
5.9kg [13lbs]
AB3
h94mm x ø260mm
h[3.7in] x ø[10.2in]
1.8kg [3.9lbs]
Burner Standard Equipment Received
Series Model Manual Jerry Can Lighting Rod Lighter Extension Spout Top Tray Baes
BK Series BK5, BK3, BK2UL 1 1 1 1 - 1 -
XL Series XL900, XL700, XL500 1 1 1 1 - - 2 - 4
XS Series XS340 1 1 1 1 - - -
VB Series VB2 1 1 1 1 - - -
AB Series AB8, AB3 1 1 1 1 1 (AB8 & AB3 only) - 1 (AB8 only)
BKSeries ABSeries XS Series VBSeriesXLSeries
INSTALLATION,
OPERATION
AND MAINTENANCE
MANUAL
PLEASEREAD THESE INSTRUCTIONS COMPLETELY
BEFOREOPERATING THE ECOSMART™ FIRE.
! WARNINGS:
IFTHE INFORMATIONIN THIS MANUAL IS NOT FOLLOWED EXACTLY,A FIRE OR EXPLOSION
MAYRESULTCAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
e-NRGbioethanol is the
ONLYfuelto be used in
thisappliance.
Installation, Operation and Maintenance Manual
In order to obtain optimal and safe results from your
appliance
, we recommend carefully reading the
entire instruction manual.
h 297mm x l 210mm x d 8mm
h [11.7in] x l [8.3in] x d [0.3in]
Jerry Can with Spill Proof Safety Spout (CARB Regulation compliant)
This 4.75 Litres [1.25Gal] Jerry Can has been chosen for its unique safety features. It includes an automatic
stop ow, a fast ow rate, a locking thumb button control, and a self-venting system. The Jerry Can will
allow safe storing/decanting of the e-NRG Bioethanol used in the Burner.
Due to safety regulations the Jerry Can provided with this package comes without fuel.
h 220mm x l 185mm x d 235mm
h [8.7in] x l [7.3in] x d [9.3in]
Lighting Rod
This long slender piece of stainless steel with a small hook return at the end enables you to safely
adjust the slider position on the Burner at any time. It is also used for the ignition procedure.
h 657mm x l 28mm x d 23mm
h [25.9in] x l [1.1in] x d [0.9in]
Lighter*
This rellable butane lighter supports the safe ignition of the lighting rod. The length of the lighter further
enhances the management of the lighting process.
* Due to safety regulations the butane lighter provided with this package comes without fuel. Small re-charge cans of butane gas with the necessary
connections can be purchased from your hardware store. Lighter image is indicative only, the model included may vary from time to time.
h 185mm x l 15mm x d 15mm
h [7.3in] x l[0.6in] x d [0.6in]
Extension Spout (AB8 & AB3 Only)
An extension spout is included with the AB3 Burner. This is for use with models that have more
restricted access to the lling point so that lling can be done in a safe manner according to the
procedures outlined in the Operations Manual.
l 500mm x ø 25mm
l[19.7in] x ø [1in]
Top Tray (BK Series only)
The BK series burners come with a protective Top Tray. All other burners do not. Top Trays for other
burners are available as accessories through your local distributor.
BK5 Top Tray BK2 and BK3 Top Tray
h 123mm x l400mm x d317mm h 93mm x l400mm x d317mm
h[4.8in] x l[15.7in] x d[12.5in] h[3.7in] x l[15.7in] x d[12.5in]
See page 11 for more information on Top Trays.
These eciency devices are a standard inclusion with the XL Series and AB8 Burners. Baes (or
Rings) are placed over the internal burner vents when cold and not operating and serve to increase the
eciency of the burner as well as further stabilise the ame of the burner.
XL Series Eciency Ring
h 10mm x l 80mm x d 10mm h 5mm x ø 158mm
h [0.4in] x l[3.1in] x d [0.4in] h [0.2in] x ø[6.2in]
www.ecosmartre.com © Copyright 2004 - 2016 The Fire Company Pty Ltd. All rights reserved. V0316e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
Standard Equipment Received
Wind Screen Static
For those models that come with a Wind Screen Static – the Wind Screen
can be xed to the front of the model via the four (4) xing points on the
rebox facade using the circular screws provided.
If a wind screen is not required, the model includes four (4) stainless steel
plugs to hide these xing points.
Jerry Can Extension Spout
Some models include an extension spout. This is for models that have
more restricted access to the lling point so that lling can be done in a
safe manner using the procedures outlined in this manual.
The Wind Screen Static, Jerry Can Extension Spout and other
accessories are available through your local distributor.
Markings
BK SERIES XL SERIES
AB SERIES
Slider position markings
These markings on the top of the burner illustrate the various settings
the burner can be operated at using the sliding mechanism.
Feature not available for models in the XL or XS Series.
BK5 BK3 & BK2UL
The following safety markings are included on the Burner. It is
important that you take the time to understand what they mean as
failure to follow instructions related to these markings could result in
property damage, bodily injury or even death.
Burner markings
These pictograms are used to bring to your attention the following
important safety messages:
DO NOT FILL WHILE
OPERATING
DO NOT FILL
WHILE HOT
Volume markings
Inside the burner you will see the following fuel level markings.
WARNING! Never ll above the MAX volume mark.
Lighting rod labels
The Caution and Warning labels that are applied to the lighting rod are
included to reinforce important safety messages. This is what they say:
risk: Never use any fuel other than e-NRG bioethanol (www.e-nrg.
com). Never re-use original packaged fuel container. Always store fuel
at room temperature in another location separate from the appliance
and away from other fuel containers. Never fuel the appliance while
it is operating or hot. Always let the combustion chamber cool in
quickly and warn others, call the Fire Department. Do not: Try to move
Keep Children Away – Do not remove the protective guard.
CAUTION: Improper use can cause pollution and health problems.
bioethanol in the appliance (www.e-nrg.com). Operate according
to manufacturers instructions. Keep the appliance clean - refer to
Operating Manual for instructions. Do not operate at lower than
minimum setting. Always operate with the doors of the room open.
Follow all applicable code requirements when using this appliance.
Keep Instruction Manual.
Burner data plate location
Every EcoSmart Fire Burner includes a data plate which provides
minimum clearances and safety information. It also includes a unique
bar code, serial number and key manufacturing information.
Package Insert
A warning sheet has been included with the burner to alert you to
reading the operations manual in full.
•e-NRGistheONLYfueltobeusedinthisappliance.Purchaseonlineatwww.e-NRG.com
or contact your local EcoSmart Firedistributor.
•Onlyuseinwellventilatedrooms
•Neverleaveareunattended
•Hotsurfacewhileinoperation–donotplaceammableitemsonorneartheappliance.
•Contactwiththerewhileinusemaycauseskinburns
•Areextinguisherisstronglyrecommended
Foroccasionaldecorativeuse.Notforheating.Registeryourwarrantyatwww.ecosmartre.com
Remove label before use.
V0415
Read and understand operator’smanual and all
safety instructions before use.
View our safety section on www.ecosmartre.com
Flammable Usewithsupplied
accessories
Keepaway
fromchildren
Donot
llwhilehot
Donotll
whileoperating
Donot
overll
! WARNING
www.ecosmartre.com © Copyright 2004 - 2016 The Fire Company Pty Ltd. All rights reserved. V0316e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
Clearances & Installation
Ensure that the mouth of the ame is positioned a minimum of 1500mm [59.1in] away from curtains,
ammable materials, and other sources of ignition. Be aware of drafts. The oor must be level and the Burner
positioned on a at surface. The Burner must only be placed into non-combustible materials and must be
installed in accordance with the outlined safety requirements and clearances. Please send drawings to your
local representative to conrm the setting complies with the manufacturer’s requirements prior to installation.
Burner Clearances
EcoSmart Fire Burners can be installed into two (2) types of settings:
A.Those that are encased by non-combustible materials similar to that
which you would nd in a traditional masonry set-up. We refer to this
installation type as “WITHIN A FIREBOX SETTING”
B.Those that are not encased by non-combustible materials and set
up in a more modern setting without sides or a top. We refer to this
installation type as “WITHOUT A FIREBOX SETTING”
A. INSERTING WITHIN A FIREBOX SETTING
BURNERS Firebox Width (X) Firebox Depth (Z) Overhead (Y) Rear (B2) Front (B1)
BK SERIES 650mm [25.6in] 365mm [14.4in] 650mm [25.6in] 30mm [1.2in] 45mm [1.8in]
XL900 1200mm [47.2in] 350mm [13.8in] 500mm [19.7in] 40mm [1.6in] 50mm [2.0in]
XL700 1000mm [39.4in] 350mm [13.8in] 500mm [19.7in] 40mm [1.6in] 50mm [2.0in]
XL500 800mm [31.5in] 350mm [13.8in] 500mm [19.7in] 40mm [1.6in] 50mm [2.0in]
XS340 450mm [17.7in] 300mm [11.8in] 450mm [17.7in] 65mm [2.6in] 45mm [1.8in]
AB8 650mm [25.6in] 450mm [17.7in] 800mm [31.5in] 30mm [1.2in] 45mm [1.8in]
AB3 400mm [15.7in] 350mm [13.8in] 500mm [19.7in] 30mm [1.2in] 45mm [1.8in]
B. INSERTING WITHOUT A FIREBOX SETTING
BURNERS Overhead (Y) Front (B1) Nearest Combustible
Radius (A)
Rear
(B2)
(Only if Non-combustible)*
BK SERIES 1500mm [59.1in] 45mm [1.8in] 600mm [23.6in] 30mm [1.2in]
XL900 1500mm [59.1in] 50mm [2.0in] 600mm [23.6in] 40mm [1.6in]
XL700 1500mm [59.1in] 50mm [2.0in] 600mm [23.6in] 40mm [1.6in]
XL500 1500mm [59.1in] 50mm [2.0in] 600mm [23.6in] 40mm [1.6in]
XS340 1500mm [59.1in] 45mm [1.8in] 600mm [23.6in] 65mm [2.6in]
AB SERIES 1500mm [59.1in] 45mm [1.8in] 600mm [23.6in] 30mm [1.2in]
*WARNING! Fire hazard. The rear wall should be non-combustible. If it is combustible, you must allow at
least 600mm [23.6in]. clearance between the wall and the rear of the EcoSmart Fire.
e.g BK SERIES
Y
X
A
B1 A
B2
e.g BK SERIES
min
20mm
[0.8]
Spacers
FRONT VIEW
A
A
B2
B1
Y
The VB2 burner is specially designed as a ‘drop-in’ burner system to a purpose-built, existing or new,
according to the manufacturers instructions before inserting the burner.
NOTE: The burner is not approved for independent installation under C-UL US.
Custom made reboxes must:
- Be made out of a non-combustible material such as stainless steel
- Be constructed to accommodate a Top Tray
- Have built in spacers of 20mm [0.8in] on all sides to ensure that it does not sit directly against any
combustible materials and an air gap is incorporated for insulation around the box construction. The use of
insulation wool is permitted.
The Fire Company Pty Ltd recommends using the Burner in a Firebox manufactured by The Fire Company
Pty Ltd only. The Fire Company Pty Ltd is not liable for any injuries or damages sustained through the use
of custom made or privately commissioned Fireboxes.
Clearances & Installation
- Installed after all gas connections or pipelines in the area are
disconnected and made safe by an appropriately qualied and
licensed professional
- Installed and operated in a xed and secure position before lling,
lighting and operating. Burners are not meant to be moved because
movement creates the risk of accidental fuel spillages. If you move
the Burner, make sure no fuel was spilled before you ignite the
Burner.
- Models from each range (Grate/Firebox Inserts/Designer/Outdoor)
have varied installation requirements. Refer to the specic section of
the manual for the detailed requirements of the model purchased.
The best location for your EcoSmart Fire is:
- In a large, open space at least 1500mm [59.1in] away from any
combustible materials, such as curtains, wallpaper, veneer, etc.
- On a level oor – the oor can be made of any material.
- In a rebox made of non-combustible materials, such as steel,
concrete, brick, or stone.
- Positioned so that any accumulation of weather debris/pooling of
water is eliminated.
- NOT INSTALLED DIRECTLY BESIDE OR NEAR WALLPAPER,
LAMINATE, VENEER OR ANY SURFACE THAT HAS NOT BEEN
FIRE RATED (THE HEAT WILL IMPACT THE MATERIAL). REFER TO
PRODUCT SPECIFICATION OF WALLPAPER, LAMINATE, VENEER
OR GLUE FOR HEAT TOLERANCES.
- Installed into a setting that has a straight back – the incorporation of
angled backs alters the aerodynamics of the ame environment and
could lead to an unstable ame behaviour.
- Fitted within a Top Tray that is not more than 200% the size of the
total Burner size.
Please note that:
- Any furniture items or ttings directly above or beside the Burner
installation must be deemed suitable for heat tolerances by
their manufacturer e.g. electronic items including screens and
entertainment equipment, wallpaper, laminates, veneers, glues and
reconstituted materials.
- A heat reective panel made of non-combustible material (ideally
stainless steel) must be installed as the surround and top of the
replace setting to assist in heat distribution. The Fire Company Pty
Ltd is not liable for any injuries or damages sustained through the
use of panels not manufactured by The Fire Company Pty Ltd.
- Glass or mirrored surfaces near the Burner installation must be
toughened.
- If inserting an Burner into an existing masonry replace, adjust the
damper within the existing replace in order to keep the heat from
escaping through the ue.
or approvals from building authorities may be required. Please
ensure you contact the appropriate parties before installing your
EcoSmart Fire.
WARNING! FIRE HAZARD. DO NOT PACK REQUIRED AIR SPACES,
(THE AREA BETWEEN THE FIREBOX AND THE SPACER) WITH
INSULATION OR OTHER MATERIALS. THE AIR SPACES ARE NEEDED
FOR PROPER VENTILATION OF THE BURNER.
FIRE SCREENS
If installing a re screen into your setting there must be a 40mm [1.6in]
gap between the burner platform and the under side of the glass
edge to enable air circulation around the burner. This assists with fuel
eciency, burner temperature and ame quality.
Installation
There are many dierent variations available for installing the Burner.
In all cases, the Burner must be:
- Installed into non-combustible material ONLY, such as stainless
steel, concrete, brick and stone
Environmental Conditions
W
materials and other sources of ignition at all times. Pay very close
a result of wind and drafts.
paper and the like.
The base of the burner within the model must never come into direct
contact with ammable materials.
Side clearances to xed and stable furniture items that are not
susceptible to movement such as lounges or patio furniture must remain
a minimum of 600mm [23.6in] away from the ame at all times.
Overhead clearances to items that are susceptible to movement
(e.g. Curtains/Trees) must remain a minimum of:
- Indoors: 1500mm [59.1in] away from the ame at all times.
- Outdoors: 2000mm [78.7in] away from the ame at all times.
Note: Stainless steel will rust or corrode over time if contamination
or debris is not cleaned or removed immediately. When not in use, it
is recommended that you protect your replace from water damage
or corrosion with a protective cover and always use the Burner Lid
included with your model to safeguard the burner.
Outdoor Clearances
Indoor Clearances
[23.6]
600mm
[78.7]
2000mm
[23.6]
600mm
[59.1]
1500mm
www.ecosmartre.com © Copyright 2004 - 2016 The Fire Company Pty Ltd. All rights reserved. V0316e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
Clearances & Installation
Top Tray
The incorporation of a Top Tray into your setting protects against heat
transference and aids in the collection of accidental spillage. Some
models come with Top Trays, others do not. Top Trays are available as
an accessory through The Fire Company or your local distributor.
The Fire Company Pty Ltd is not liable for any injuries or damages
sustained through the use of Top Trays not manufactured by The
Fire Company Pty Ltd;
When installing multiple Burners a maximum of three [3] Burners may
be installed into the one Top Tray (excluding the XL Series which can
only have one [1] Burner per Top Tray). Special considerations should
be made to multiple Burner installations in order to avoid potential
accidents. Contact your local distributor about design and analysis
advice to minimise adverse impacts.
Top Trays provided by The Fire Company are tted directly into the
Burner shelf from above. The Burner is then inserted into the Top Tray
setting and adjusted (using the levelling screws) to sit ush.
The size of the cut-out should not give more than 5mm [0.196in]
clearance. Top Trays must not be more than 200% of the total size
of the corresponding Burner.
For cut out dimensions for your model please contact your local
distributor.
Physical model dimensions should be veried against cut out
dimensions BEFORE installation begins to conrm tolerances align.
Ventilation
EcoSmart Fires do not require any form of permanent xture or tting,
such as a ue for ventilation, a permanent connection or any kind of
xed utility for fuel supply.
Do not cover any existing ventilation systems or structures that
are built or installed within the chosen installation area.
To ensure adequate ventilation, make sure to follow the guidelines in
the table shown.
Underwriters Laboratories calculates adequate air exchange as
follows:
In a house of typical construction, that is, one that is not of unusually
tight construction due to heavy insulation and tight seals against air
inltration, an adequate supply of air for combustion and ventilation is
provided through inltration. However, if the Burner is used in a small
room where less than 5.7m3[200ft3] of air space is provided for each
1000 BTU per hour of appliance rating (considering the maximum
Burner setting), the door(s) to adjacent room(s) should be kept open
or a window to the outside should be opened at least 25.4mm [1in] to
guard against potential build up of indoor air pollution. Do not install or
operate in a bathroom or any other small room.
Model Minimum room size
BK5 The room cannot be less than 70m3[2472ft3] per burner.
BK3 The room cannot be less than 45m3[1589ft3] per burner.
BK2UL The room cannot be less than 45m3[1589ft3] per burner.
XL900 The room cannot be less than 110m3[3884ft3] per burner.
XL700 The room cannot be less than 90m3[3178ft3] per burner.
XL500 The room cannot be less than 80m3[2825ft3] per burner.
XS340 The room cannot be less than 45m3[1589ft3] per burner.
VB2 The room cannot be less than 45m3[1589ft3] per burner.
AB8 The room cannot be less than 116m3[4096ft3] per burner.
AB3 The room cannot be less than 40m3[1413ft3] per burner.
The ventilation requirements must always be met. The burner must only
be installed in areas that are protected from the draft eects of cross
ventilation.
www.ecosmartre.com © Copyright 2004 - 2016 The Fire Company Pty Ltd. All rights reserved. V0316e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
Fuel Type
The EcoSmart Fire Burners are fuelled by a renewable energy source
called e-NRG Bioethanol.
FLAMMABLE!: Refer to warnings on page 1.
Keep the fuel out of reach of children. Store e-NRG Bioethanol at a
safe distance at all times - a minimum of 1500mm [59.1in] from the
appliance.
To order your e-NRG Fuel contact:
Australia
Visit - www.e-NRG.com.au
Call - 1300 003 NRG
USA
Visit - www.e-NRG.com
Call - (888) 670 ENRG
Or contact your local EcoSmart Fire distributor.
Burners Volume
Capacity
Thermal Output
Net (MAX)
Heats
on Average
Fuel Consumption Approx burn time
on MAX setting
BK5 5 Litres
[1.3 Gallons]
14 MJ/hr
13,000 BTU/hr
3.5 kW
Over 35m2
[376.7ft2]0.64 L/hr [0.17 Gal/hr] on MAX 7 - 11 hours
BK3 3 Litres
[3 Quarts]
9.04 MJ/hr
8,565 BTU/hr
2.51 kW
Over 25m2
[269ft2]0.46 L/hr [0.12 Gal/hr] 6 hours
BK2UL 2 Litres
[2 Quarts]
10.09 MJ/hr
9,570 BTU/hr
2.8 kW
Over 25m2
[269ft2]0.49 L/hr [0.13 Gal/hr] 4 hours
XL900 9 Litres
[2.4 Gallons]
16 MJ/hr
15,000 BTU/hr
4.4 kW
Over 60m2
[645ft2]0.8 L/hr [0.21 Gal/hr] 8 - 13 hours
XL700 7 Litres
[1.8 Gallons]
14.5 MJ/hr
13,650 BTU/hr
4 kW
Over 50m2
[538ft2]0.7 L/hr [0.18 Gal/hr] 9 - 12 hours
XL500 5 Litres
[1.3 Gallons]
12 MJ/hr
11,430 BTU/hr
3.35 kW
Over 40m2
[430.6ft2]0.5 L/hr [0.13 Gal/hr] 10 - 13 hours
XS340 2.5 Litres
[2.5 Quarts]
8.93 MJ/hr
8,530 BTU/hr
2.5 kW
Over 20m2
[215ft2]0.45 L/hr [0.12 Gal/hr] 5 hours
VB2 2 Litres
[2 Quarts]
7.236 MJ/hr
6,180 BTU/hr
2.5 kW
Over 15m2
[161ft2]0.5 L/hr [0.13 Gal/hr] 6 hours
AB8 8 Litres
[2.1 Gallons]
21.56 MJ/hr
20,433 BTU/hr
5.99 kW
Over 60m2
[645ft2]
When used indoors.
1.1 L/hr [0.29 Gal/hr] 7- 11 hours
AB3 2.5 Litres
[2.5 Quarts]
6.14 MJ/hr
5,800 BTU/hr
1.7 kW
Over 20m2
[215ft2]
When used indoors.
0.31 L/hr [0.1 Gal/hr] 8 - 11 hours
All EcoSmart Fire Burners have a Thermal Eciency of over 90%.
NOTE: These values are indicative only and may vary depending on the model purchased and installation and the country where the e-NRG
Bioethanol is sourced.
How to Operate the Burner
Follow these instructions to operate your Burner safely.
in original container or Jerry Can. Store away from all sources
of ignition, including pilot lights. Check your local laws and
regulations for proper handling and storage.
Regulatory Information for the Safe Handling and
Storage of e-NRG Bioethanol
Purchasing your e-NRG Bioethanol.
e-NRG Bioethanol is the ONLY fuel to be used in this appliance.
To order your e-NRG Fuel contact:
Australia
Visit - www.e-NRG.com.au
Call - 1300 003 NRG
USA
Visit - www.e-NRG.com
Call - (888) 670 ENRG
Or contact your local EcoSmart Fire distributor.
e-NRG Bioethanol is classied as a Dangerous Goods Flammable Liquid
Class 3, PGII and is regulated by specic standards and rules. You must
familiarise yourself with the appropriate regulations of your country in
order to safely and legally store, handle, decant and use this fuel.
e-NRG Bioethanol containers are recyclable and should be disposed
of accordingly.
Decanting your e-NRG Bioethanol into the Jerry Can
Decanting must be performed in a well-ventilated area to ensure that
any spillage is easily contained and away from any ignition source.
Spill Proof Safety Spout attached.
outlined below.
A.USING THE JERRY CAN
INCLUDED WITH THIS
BURNER:
1. Remove the nozzle from your
Jerry Can.
2. Carefully decant the fuel from
the bottle into the Jerry Can
through its opening, avoiding
spillage (you may need
to decant multiple bottles
depending on the packaging volume purchased). If spillage occurs,
clean thoroughly before proceeding. (Refer to Troubleshooting on
page 20).
3. Re-screw the cap tightly back onto the Jerry Can to contain fuel and
avoid accidental spillage.
4. Test that it is closed securely before moving away from your
decanting area.
5. You are ready to approach the Burner.
B. USING THE e-NRG
FUEL BOTTLE:
1. Remove the cap from the fuel
bottle.
2. Attach the adapter to the fuel
bottle.
WARNING: Fuel containers
without ame arresters, if used
improperly, can result in the
inammation of the fuel within
the container, which may cause
personal injury or property
damage. Never ll the burner
directly from the e-NRG bottle,
risk of explosion.
3. Attach the Spill Proof Safety
Spout to the adapter. Test
that it is closed securely
before moving away from your
decanting area.
4. You are ready to approach the
Burner.
www.ecosmartre.com © Copyright 2004 - 2016 The Fire Company Pty Ltd. All rights reserved. V0316e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
How to Operate the Burner
Decanting your e-NRG Bioethanol from the Jerry Can
into the Burner
WAR
WARNI
directly onto the burner.
WARNI
it on the base of the grid. Used properly, the Jerry Can spout will help
As an additional safety measure, we recommend that you remove the
burner and check that there is no unexpected fuel collection in the Top Tray.
The Fire Company Pty Ltd recommends that the quantity of e-NRG
Bioethanol poured into the burner be burnt until empty rather than
extinguishing the re early. Extinguishing the re early can result in a
larger amount of residual fumes in the Burner and a more volatile
re-ignition.
When fumes are combined with excess fuel it could be a hazard to
people who are unaware of the Fire operation and its condition of use
(e.g smokers). Ensure only those who have read the instructions attempt
to operate the burner.
AB Series:
To ll the AB Series, position the
Jerry Can spout in the middle of
the burner mouth.
4
4. Re-position the Burner slider
ensuring the grid work of the
burner is visible through the
lling point. This will clear the
lling point for the insertion of
the Jerry Can spout as well
as allowing visual monitoring
of the amount of fuel being
added, according to the volume
markings on the Burner.
5. Once ready, carefully place
the Jerry Can spout inside
the lling point. NEVER ll
over the maximum level as
indicated on the burner vent
inside the Burner and only ll
to the level that you require for
burning time.
6. Use both hands to pour. Place
the palm of one hand on the
top of the nozzle with your
thumb on the green button.
Use your other hand to tip
the can vertically and hold it
steady. Press down on the
green button to release the
fuel. To stop the ow, simply
release the green button.
8
7. When lling is complete, ip
the lid that covers the lling
point so it closes the lling
point.
8. Re-position the slider to the
fully open position. Check
surrounding area for any
spillage. WARNING: Fire
hazard. Clean up any spilled
fuel before lighting the
burner. See Troubleshooting
page 20 for clean-up
procedure.
9
1500mm [59.1in]
9. Make sure that the Jerry Can
is at least 1500mm [59.1in]
away from the replace before
you ignite the re.
1
3
21. Remove the transport locking
strip and position the slider
mechanism setting so the
chamber is fully open.
2. Inspect inside the burner
mouth to ensure it is clean and
clear of any foreign particles.
3. Access the lling point by
ipping the small lid which is
located in the bottom right
corner of the burner.
XL Series:
The XL Series feature a spring
loading cap. It is engineered so
that the Jerry Can spout is fully
enclosed prior to releasing the
fuel supply, thus allowing lling
at a high rate, whilst eliminating
splashing as the fuel is being
decanted.
The XL ame is most visible
when the burner is lled to the
MAX line.
VB2
To ll the VB Series, position the
Jerry Can spout in the middle of
the burner mouth.
5
7
How to Operate the Burner
Lighting the Burner
Keep hands and face the length of the lighting rod away from
the Burner at all times, particularly when igniting. Before lighting,
ensure that the Burner is clear and ready for use. Open the slider fully
and wait for 60 seconds for the residual fumes to dissipate before
lighting.
Check the slider is free from obstruction and operating smoothly.
(Refer to Troubleshooting section on page 20 if diculties are
experienced).
Do not smoke while lighting the Burner, and make sure that no one is
in front of the replace while igniting the Burner. Only use the lighter
supplied with your EcoSmart Fire.
1
2
3
4
1. Dip the lighting rod tip into the chamber opening “Burner zone” to
wet the end.
2. Lift the lighting rod away from the Burner (do not drip fuel on the oor).
3. Ignite the lighter and make contact with the lighting rod as if lighting
a candle.
4. Dip the ignited lighting rod back into the Burner zone to ignite the
contained fuel.
5. Allow residual ame on lighting rod to burn out.
NOTE: The XL900 & XL700 is best ignited from the right hand side of
the ignition zone.
Once lit there will be a residual ame on the lighting rod that must burn
out before putting the rod away. If the ame on the lighting rod dies
before reaching the burner, repeat the procedure until successful.
Due to some residual oil in the bres we use in the Burner there is a
stronger smell when rst operating. It will decrease substantially after
the rst few times you use the Burner, and even more so over time. To
minimise this, wash the burner out in hot water before using. The Burner
must be completely dry and cool before lling with fuel.
Regulating the Flame
Not applicable for BK2UL or BK3 models.
Wait until the re is established (approx 10 minutes) before regulating.
To decrease the ame intensity insert the lighting rod tip through the
circular ring and push forward gently to desired setting. Only use the
lighting rod supplied with your EcoSmart Fire to avoid hand burns.
To increase the ame intensity insert the lighting rod tip through the
circular ring and pull back gently to desired setting. Only use the lighting
rod supplied with your EcoSmart Fire to avoid hand burns.
These eciency devices are a standard inclusion with the XL Series and
AB8 Burners. Baes (or Rings) are placed over the internal burner vents
when cold and not operating and serve to increase the eciency of the
burner as well as further stabilise the ame of the burner.
Note: Regulatory function and accessories not applicable to BK2UL, VB2
and AB3 – in these models, the control must be in the fully ON or fully
OFF position only. The ame cannot be adjusted.
XL900 4 x Baes
XL500 2 x Baes AB8 1 x Eciency Ring
XL700 3 x Baes
Important: All Burner parts will age over the course of time through
natural processes associated with use, heat and ame.
Please also note that new stainless steel has an oil coating that will burn
o during the rst few uses. You will notice an accumulation of carbon
around the top opening of the Burner zone and its vents. This will appear
quickly and is normal. You will need to perform your rst maintenance
after approximately 20 litres [5.28 Gal] of e-NRG Bioethanol burnt.
After this, the accumulation will be far slower and maintenance can then
occur every 50 litres [13.20 Gal] of e-NRG Bioethanol burnt. If anything
abnormal appears, do not operate the appliance. If the re is running, turn
it o immediately and contact your distributor before using again.
www.ecosmartre.com © Copyright 2004 - 2016 The Fire Company Pty Ltd. All rights reserved. V0316e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
How to Operate the Burner
Turning your Burner OFF
- Extinguishing the Flame
1. Let it burn until the fuel is consumed. The ame will extinguish
when no fuel is left.
2. Use the lighting rod to move the circular ring to the fully OFF
position.
WARNING: Fire hazard. With either method, let burner cool for
at least 60 minutes before refueling.
XL Series and XS Series:
The XL Series and XS340 have a ip lid shut-o mechanism.
The lid ips across the ignition zone which extinguishes the ame.
AB Series and VB Series:
A lid is used to extinguish the ame.
Re-igniting the Burner
WARNING!
e-NRG BIOETHANOL IN THE BURNER.
PERFORMED ABOVE AND BESIDE THE BURNER TO AVOID
DRIPPING THE FUEL AT ANY STAGE OF THE LIGHTING
PROCESS OUT OF THE FIREBOX ONTO THE FLOOR.
ADDITIONAL e-NRG BIOETHANOL WHEN THE FLAME IS GOING
OR WHEN THE BURNER IS HOT.
e-NRG BIOETHANOL IS THAT
THE FLAME PRODUCED CAN BE NEARLY INVISIBLE IN
NORMAL DAYLIGHT CONDITIONS OR WHEN FIRST LIT. BEING
DIFFICULT TO SEE, AN INEXPERIENCED PERSON CAN EASILY
ASSUME THE BURNER IS EMPTY AND NEEDS FILLING.
ASSUME BURNER IS LIT, EVEN IF YOU DON’T SEE FLAME.
FOLLOW PROCEDURE TO EXTINGUISH FLAME AND ALLOW
UNIT TO COOL BEFORE ATTEMPTING TO REFUEL. NEVER
REFUEL WITH BURNER LIT OR WHILE UNIT IS HOT.
1. Move the slider/hinge so the Burner opening is fully open.
2. Wait 60 minutes before re-igniting the Burner. The Burner should
be at room temperature. Please be aware that if this time is not
respected the ignition could be pressurised and therefore stronger. A
pressurised ignition can cause serious burns if you are close to the
Burner.
3. Re-ignite as described in “Lighting the Burner”.
Regular Safety Checks
regular safety checks. Please take the time to familiarise yourself
(and any other users) with the safety procedures associated with
using your EcoSmart Fire.
e-NRG bioethanol is the ONLY fuel suitable for use in this
appliance.
Check your burner is in good working condition, the shut o
mechanism is working smoothly, the lling point is accessible and
eective, nothing foreign has fallen into it and make sure there is
no visual or physical damage to the burner
Frequently inspect all around the installation – including lifting the
burner out of its position to ensure that no fuel has accumulated
in or around the setting at any time
Take out your operations manual and refresh your memory on the
operational procedures for using this product – it’s available on
our website too
Give your burner a good clean, they can be washed out with hot
soapy water and left to dry - or pop it in your dishwasher on the
hot pan cycle with detergent (refer to your Operations Manual)
Check the operation of your Jerry Can, re extinguisher, lighter
and lighting rod to ensure you have the right tools to use for
safely operating your re - replacement accessories are available
from your closest distributor
Check your fuel supply is stored according to regulations – if you
are unsure contact your local distributor
Check that all ammable items are within safe distance from the
ame – that’s a minimum of 1500mm [59.1in] at all times in all
conditions
And remember, never overll your burner, never ll your burner
whilst it is in operation or hot, never leave a re unguarded and
never leave children unsupervised
www.ecosmartre.com © Copyright 2004 - 2016 The Fire Company Pty Ltd. All rights reserved. V0316e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
Caring for your EcoSmart Fire
Maintenance and cleaning must only be performed when the
Burner is OFF, COMPLETELY EMPTY & DRY and at ROOM
TEMPERATURE.
If service is required, there are two specic areas to check for cleaning.
These are the Burner and the Firebox or immediate surrounds in cases
where a rebox has not been installed.
General surrounds are maintained as you would a standard piece
of furniture by dusting and polishing the surfaces on a regular basis
during your general cleaning routine.
Cleaning the Burner
The surface of the Burner will change colour on very hot spots.
In addition, over time a lm of black residue will appear on the two
vents of the Burner, usually starting from the MAX line within the Burner
on the slider, and around the burning zone of the Burner top.
Remove with care – the black residue is a carbon left over from the
combustion. It stains.
1. When the re is o and empty, use a vacuum cleaner for general
cleaning on visible surface.
2. Brush/scrape the black material gently from the vents and the slider
towards the bottom inside of the Burner.
3. Use a vacuum cleaner to remove residue inside the Burner, around
the slider rails and around the top opening of the burning zone.
4. To nish cleaning use a damp disposable cloth and wipe until no
residue remains.
Clean your unit after you have used 50 liters [13.20 Gal.] of fuel or as
soon as you notice black deposits on or near the Burner.
Black marks can be removed from the stone, solid surfaces or stainless
steel with a mild abrasive washing product such as JIF® or similar. It is
recommended to test a small area rst to ensure the cleaning product
chosen is appropriate and will not mark or damage the surface.
After extensive use, if your Burner smells unusually strong – when
empty and cold, remove the Burner from its setting and wash the
Burner in hot, soapy water and rinse thoroughly under running water.
Let it dry before replacing in unit.
Cleaning the Firebox
As the stainless steel is exposed to ame and heat for a long period of
time, its colour will eventually change.
To clean:
1. Use a disposable damp cloth to wipe the surface that needs cleaning
(go with the grain) using a mild abrasive product such as JIF®. Rinse
well with a wet cloth.
2. After cleaning do not light the re until all surfaces are completely
dry. You can enhance the shine by using a stainless steel cleaner and
polish. Spray it on a disposable cloth and wipe the surface until you
achieve an even shine.
Any stainless steel cleaner and polish leaves a residual lm on surfaces.
This lm will burn o and appear black when directly exposed to the
ame, so be careful not to apply too much and rinse away thoroughly.
Troubleshooting
1. There is smoke or a foreign smell coming from the Burner when
burning
a. There may be waste burning that should not be in the Burner.
b. You are using the wrong fuel (it is imperative that you ONLY use
e-NRG Bioethanol).
c. You have placed something around/above the ame that has not
been approved or recommended.
d. If the Burner is empty (the ame is dying) or you have just turned the
re OFF, this is normal. Just like when you blow out candles.
Solution
Shut the Burner to the OFF position and wait until it cools down. Clean/
service the Burner and remove objects/waste.
2. When I attempt to light the Burner, it does not start
a. You have not put enough fuel in the Burner.
b. You have not used the right fuel (it is imperative that you ONLY use
e-NRG Bioethanol).
c. The Burner opening is obstructed, there needs to be adequate
ventilation for the ame to start.
d. The e-NRG Bioethanol is cold and takes time to ignite.
e. If used outdoors, the fuel may have been diluted with rain water.
Solution
Check fuel level, it must be above the 1 litre [1 Quart] line, check type of
fuel used, and open the slider/hinge. Repeat starting procedure until the
Burner warms up and remains ignited. If lled with water, empty burner,
clean and clear Burner and re-set up ready for re-lling.
a. It may be that the speed used to close the Burner opening was too
slow.
b. There are particles obstructing the shut-o mechanism.
Solution
Ensure that there is nothing obstructing the shut-o mechanism. Attempt
to extinguish again smoothly with the shut-o mechanism. If it does not
extinguish, burn the fuel until empty and the ame dies out naturally and
contact your distributor. Do not use again until it has been serviced.
If you have overlled the Burner and the ame is burning strong,
prepare your extinguisher just in case, and monitor the ame till the
situation goes back to normal as you will not be able to turn it OFF. Do
not blow or throw a blanket on it. Do not pour water on it.
a. The Burner slider/hinge is dirty or lled up with debris left after
combustion.
b. There may be something stuck or obstructing the shut-o
mechanism e.g. something may have fallen into the Burner.
c. The Burner has been physically damaged internally (e.g. if it has been
dropped).
Solution
Clean/service the Burner and see if you nd the obstruction. If you do
not nd anything, contact your distributor. Do not use again until it has
been serviced.
5. I have spilt some fuel, what do I do before lighting?
Remove all ignition sources. Keep people away from the area. Wipe
up spilt liquid thoroughly using a dry cloth, wipe again with a cloth
dampened with water. Avoid breathing vapours. Ventilate enclosed
space by opening windows and doors.
ONLY ignite when the area is completely dry and you are certain that all
spilt fuel has been removed. Please refer to SDS for e-NRG Bioethanol.
This is likely to be caused by a strong draft blowing on the ame.
Locate and remove the source of the draft (it may be that you have a
window/door open or fan operating that is directly pushing air towards
the re). If you cannot remove the source of the draft and the ame is
too volatile, turn the re OFF. You will need to rethink the positioning of
your unit before operating again or install a rescreen to minimise the
draft eect. Contact your distributor.
7. The Jerry Can doesn’t work properly
Please contact your distributor for further instructions. Do not attempt to
ll the Burner with an unapproved alternative fuel can.
www.ecosmartre.com © Copyright 2004 - 2016 The Fire Company Pty Ltd. All rights reserved. V0316e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
After Sales Service
product. NOTICE: If you need service or assistance, we suggest
you follow these steps.
After Sales Service for your EcoSmart Fire
The Fire Company Pty Ltd oers an international network of authorised
service agents. The use of other than approved EcoSmart Fire parts
and accessories may damage or reduce the performance of your Fire
and may also endanger the user. The Terms and Conditions of warranty
may also be aected. A full list of contacts can be found on
www.ecosmartre.com
Please note
Charges will apply for services performed outside the warranty period.
If you are asked to send your Fire into a service centre please ensure
that it is securely packed in materials equivalent to how you received
your Fire to avoid possible damage that will not be covered by The Fire
Company Pty Ltd. Freight must be pre-paid. Include a covering letter
outlining the defect and your contact details.
1. Before calling for assistance
Check the things you can do yourself. Refer to the Installation, Operating
and Maintenance Manual supplied with your Fire to ensure that it is
correctly installed and that you are familiar with its normal operation.
2. If You Need Service*
The Fire Company Pty Ltd has a network of independent EcoSmart Fire
Authorised Customer Service Centres whose fully trained technicians
can carry out any service necessary on your appliance.
Contact the dealer from whom your purchased the appliance, who can
advise you where to obtain service.
3. If you need assistance or have a problem*
If you need assistance or have a problem please contact your local
retailer or distributor, or visit www.ecosmartre.com for Head Oce
details.
Talk to one of our customer service representatives. They can instruct
you in how to obtain satisfactory operation from your appliance or, if
necessary, recommend an Authorised Customer Service Centre in your
area.
*If you must call or write, please provide: Name and Address, Model Number, Serial Number,
Date of Purchase, venue and a complete description of the problem. This information is needed
in order to better respond to your request for assistance.
Reproduction of this manual in any manner, in any language, in whole or in part without prior
written permission is prohibited. The Fire Company Pty Ltd reserves the right to correct any
errors or misprints. We also reserve the right to alter information without notication. The
information provided herein is believed to be correct but is not guaranteed.
International Patent Pending – Trademarks Pending – All Designs Registered.
Your Warranty
Your EcoSmart Fire is covered by a transferable limited warranty and
a solid service and support network should you need it. At The Fire
Company Pty Ltd, we believe in supplying you with the best, most
user friendly replace and providing you with the means to keep it that
way. Many aspects of the EcoSmart Fire are hand-produced, hand-
nished and use natural materials, which makes them subject to minor
variations in nish and size.
All of our pieces will mature and age over the course of time, through
natural processes associated with use and with heat and ame.
These changes are an essential part of the dynamic of the piece. The
Fire Company Pty Ltd reserves the right to make minor amendments
without prior notice.
The Warranties set out above are express Warranties given by The Fire
Company Pty Ltd and are in addition to the rights and remedies which
are conferred upon consumers by Trade Practices Act 1974 of the
Commonwealth and other Commonwealth, State or Territory legislation.
Service under the warranties set out above must be provided by
The Fire Company Pty Ltd Authorised Customer Service Centre
which shall provide service during their normal working hours.
be produced when making any claim.
FIRST NAME
LAST NAME
EMAIL
CITY STATE ZIP
COUNTRY
DATE OF PURCHASE
PURCHASED FROM
PRIMARY USE
MODEL NAME
SERIAL NUMBER
You will nd this on the dataplate on the side of the burner.
For warranty claims please contact your local distributor. If there is not
a local distributor in your country please visit
to source the details of the country closest to you.
*Do not return this form to The Fire Company Pty Ltd, please retain for
your own reference.
Length of warranty The Fire Company Pty Ltd
undertakes to: The express warranties do not include:
FULL TWO YEARS WARRANTY
FROM DATE OF PURCHASE
ON STAINLESS STEEL PARTS
INCLUDING RAW, LINISHED AND
POWDER COATED.
ONE YEAR WARRANTY FROM
DATE OF PURCHASE ON MILD
STEEL INCLUDING POWDER
COATED AND CHROME PLATED,
CEMENT, GLASS, LEATHER,
FABRIC AND MDF (PAINTED OR
CEMENT RENDERED).
(Stone chipping, paint or leather
scratches and general scratches
are not covered by warranty)
Repair or, at our option, replace
without cost to owner either for
materials or labour, any part that
is found to be defective.
A. Service calls to:
1. Correct the installation of the Fire.
2. Instruct you how to use the Fire.
B. Repairs when the EcoSmart Fire has been used in other than
normal domestic/commercial use or when not used in accordance
with the Installation, Operating and Maintenance Manual.
C. Repairs when the EcoSmart Fire parts or models have been
modied or altered in any way that has not been approved in writing by
The Fire Company Pty Ltd.
D. Repairs when the Fire has been dismantled, repaired or serviced by
anyone other than an authorised representative of The Fire Company Pty Ltd.
E. Pick up and delivery.
F. Normal maintenance as required in the Installation, Operating and
Maintenance Manual supplied with the EcoSmart Fire.
G. Transportation or traveling costs involved in the repair when
the appliance is installed outside The Fire Company Pty Ltd’s
AUTHORISED CUSTOMER SERVICE CENTRES’s normal service area.
H. Damage to the Fire caused by accident, misuse or Act of God.
I. Any incidental shipping or holding costs to deliver your Fire or
parts to an Authorized Customer Service Centre.
Showrooms 3 & 4, 40-42 O’Riordan Street
Alexandria NSW 2015 Australia
Tel: +61 2 9997 3050 Email: info@ecosmartre.com
REV0316
The Fire Company Pty Ltd
Showrooms 3 & 4, 40-42 O’Riordan Street
Alexandria NSW 2015 Australia
tel +61 2 9997 3050 fax +61 2 9997 6050
email info@ecosmartre.com
www.ecosmartre.com
PAGE 1 OF 1
CARE AND
MAINTENANCE
IMPORTANT
1. Concrete is a porous material. It is important to avoid dripping liquid
(such as bioethanol or alcohol) onto the concrete surfaces as it may
break down the sealer and stain the surface permanently.
2. Do not put HOT burner lids down on the concrete surfaces. It could
damage the model.
Maintenance and cleaning must be performed only when the burner
is OFF, COMPLETELY EMPTY, DRY and at ROOM TEMPERATURE.
OUR CONCRETE COMPOSITE
Concrete is a natural material and therefore each and every model will be
unique in appearance.
After a concrete surface is polished there are a variety of visual dierences
that may be seen including water marks, trowel marks, marbling, mottled
eects and random spotting etc. We cannot predict where the eects will
show or what they will be – it is part of the beauty of concrete.
Examples of acceptable variations
Cleaning
The solid surface surrounds of your EcoSmart Fire can be cleaned
using mild soap and warm water with a soft cloth.
Do not use heavy abrasives, bleach based products or ammoniated
cleaners - use of such cleaners will wear down the sealer and result in
scratches and decease stain resistance. We do not recommend use of
most natural cleaners (which are often citrus based), as the cleaning agent
is typically highly acidic and can damage natural materials.
It is recommended to test a small, discreet area rst to ensure the cleaning
product will not mark or damage the surface.
Avoiding Stains
In the event that the coating is knowingly cut, scraped, or damaged, a
new layer of sealer should be applied. Spills should be wiped up as soon
as possible. While the sealer performs well against stains from oils and
acidic materials, prolonged exposure may cause a breakdown of the
sealer and possible discoloration.
Do not place hot objects on the surface as they may cause discoloration.
Using a trivet is recommended. Refrain from applying blue painter’s tape
or other adhesives directly to the product.
Although not considered a defect, non-structural hairline cracks are
possible and may result from shrinkage and the natural curing process. If
hairline cracks do appear, immediately apply a sealer to prevent moisture
from seeping into the cracks and causing discoloration. Re-seal the
surrounding surfaces periodically.
General Maintenance
Concrete is a porous material and while the surface is sealed at point of
manufacture, the sealer may break down over time due to environmental
factors like UV rays and general use. We recommend that you seal the
concrete surfaces on an annual basis using a suitable sealer which will help
in renewing the protective sealer layer on your product. Your distributor
will know of the best brand to use in your local market. Use the protective
cover when not in use.
Removing Stains
Even with adequate sealer, liquids like red wine, oil, and other acid
products could still break down the sealer and be absorbed into the
material - particularly if not well maintained. To remove you could try a
ne grit sand paper to remove the stains from the surface (remembering
to test a small patch in a discreet area rst to ensure it doesn’t damage
the surface). Then re-apply sealer.
STAINLESS STEEL
Cleaning
Routine cleaning can be accomplished by using warm water and a cloth.
When cleaning stainless steel always wipe in the direction of the grain.
A drop of mild dish detergent and warm water is often all you need to
get tougher dirt o of your stainless steel. Use a soft, damp cloth to
wipe away any remaining residue.
Dry out completely before re-using the appliance.
CAUTION: HEAVY AND FRAGILE
Lift directly UP, then move
to avoid putting stress
on the seams. Fractures
may result if pulled in an
outwards direction.
HANDLE WITH EXTREME CARE.
Product can chip or fracture if not
handled as delicate.
Move only with four
men, one on each
corner.
V261115
YOUR SAFETY IS OUR FIRST PRIORITY
e-NRG is ONLY suitable for use in liquid bioethanol res. Do not use in
anything with a wick, or anything designed for other fuel types such as
gel, kerosine, gasoline, etc. Always follow recommended procedures
provided by the replace manufacturer.
e-NRG is ONLY to be used in compliance with these Operating Procedures
and the Operating Procedures of the bioethanol replace where you intend to
use this product.
Please refer to the Safety Data Sheet (SDS) for important Health and
Safety information.
WARNING: Fuel containers without ame arresters, if used improperly, can
result in the inammation of the fuel within the container, which may cause
property damage, personal injury, or even death.
NEVER pour e-NRG over an open ame.
NEVER ll an appliance/burner directly from the e-NRG bottle,
risk of explosion.
When using in a bioethanol replace that does NOT have an
EcoSmart Fire Burner:
e-NRG must be decanted into an approved Jerry Can that is tted with a
ame arrester following the instructions outlined below.
1. Remove the cap from your e-NRG bottle and the spout from the Jerry
Can.
2. In a safe location, away from any source of ignition, carefully decant
the fuel from the bottle into the Jerry Can through its opening, avoiding
spillage. If spillage occurs, clean thoroughly before proceeding.
3. Re-screw the cap tightly back onto the Jerry Can to contain fuel and
avoid accidental spillage. Test that it is closed securely before moving
away from your decanting area.
4. You are ready to approach the burner (the burner must be off and
in a cold state). Once the e-NRG bottle is empty, put the original lid
securely back onto the bottle for safe recycling.
1. 2.
3. 4.
INSTRUCTIONS FOR SAFE USE
This decanting procedure must be performed in a well ventilated space
away from any sources of ignition.
When using an EcoSmart Fire Burner:
If you are an owner of an authentic EcoSmart Fire, you would have
received a Jerry Can with an attached Safety Spout as part of the
standard operating accessories. An Adapter is available to connect the
Safety Spout to the e-NRG bottle which eliminates the need to decant
the fuel from the bottle into the Jerry Can.
1. Attach the Adapter to the Safety Spout.
2. Attach the Safety Spout with Adapter to the e-NRG bottle and ensure
it is securely fastened. You are ready to approach the burner (the
burner must be in an off/cold state).
Without the e-NRG Adapter the procedure below must be followed.
Manuals and videos are also available online:
www.ecosmartre.com/about/replace-safety
2.1.
Operating Procedures
& Safety Data Sheet
QUESTIONS?
If you have any questions please visit
www.e-nrg.com/safety
, or if you
prefer to speak to a Customer Service Representative, please contact us.
+1 (888) 670 ENRG / [email protected]
Safety Spout
Adaptor
Safety Data Sheet
Distributed by EcoSmart Inc.
5870 W. Jefferson Blvd, Suite L, Los Angeles, CA 90016
P: +1 888 670 3674 F: +1 310 945 3339 www.e-nrg.com
Page 2
V072216
Section 1. IDENTIFICATION
Product Name: e-NRG
Product Code: 00101
SDS Date: July 22, 2016
EcoSmart Inc.
5870 W. Jefferson Blvd, Suite L
Los Angeles, CA 90016
General Information: 888-670-3674
CHEMTREC: 800-424-9300
Section 2. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW:
GHS Classication:
Flammable liquids (Category 2)
Skin irritation (Category 2)
Eye irritation (Category 2B)
Specic organ toxicity – single exposure (Category 3)
GHS Labeling
Symbol:
Signal Word: Danger
Hazard Statements:
Highly ammable liquid and vapor.
Causes skin irritation.
Causes eye irritation.
May cause respiratory irritation.
Precautionary Statements:
Prevention:
Keep away from heat/sparks/open ames/hot surfaces. No smoking.
Keep container tightly closed.
Ground/Bond container and receiving equipment.
Use explosion-proof electrical/ventilating/lighting equipment.
Use only non-sparking tools.
Take precautionary measures against static discharge.
Wear protective gloves/protective clothing/eye protection
/face protection.
Wash hands thoroughly after handling.
Avoid breathing mist/vapors/spray.
Use only outdoors or in a well-ventilated area.
Response:
IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse
skin with water/shower.
In case of re: consider carbon dioxide, dry chemical powder, dry sand,
limestone powder, or alcohol resistant foam to extinguish.
If on skin: Wash with plenty of water.
If skin irritation occurs: Get medical advice/attention.
Take off contaminated clothing and wash it before reuse.
If in eyes: Rinse cautiously with water for several minutes. Remove contact
lenses, if present and easy to do.
Continue rinsing.
If eye irritation persists: Get medical advice/attention.
If inhaled: Remove person to fresh air and keep comfortable for breathing.
Call a poison center/doctor is you feel unwell.
Storage:
Store in a well-ventilated place. Keep cool. Keep container
tightly closed.
Store locked up.
Disposal:
Dispose of contents/ container to an approved waste disposal plant.
Potential Health Effects: See Section 11 for more information
This product does not contain carcinogens or potential carcinogens as
listed by OSHA, IARC, or NTP.
This material contains components that are considered hazardous by the
OSHA Hazard Communication Standard (29 CFR 1910.1200).
Potential Environmental Effects: See Section 12 for more information.
Section 3: COMPOSITION/INFORMATION ON INGREDIENTS
No. Component
CAS REG. NO. Amount %
OSHA ACGIH
TWA STEL TWA STEL
1Ethyl Alcohol
CAS #64-17-5 1-100 1000
ppm
Not
Avail
1000
ppm
Not
Avail
2Isopropyl Alcohol
CAS #67-63-0 1-100 400
ppm
Not
Avail
400
ppm
Not
Avail
Section 4: FIRST AID MEASURES
Emergency rst aid procedures by route of exposure:
Inhalation: If symptoms are experience, remove source of contamination or
move victim to fresh air. If affected person is not breathing, apply articial
respiration. If breathing is difcult, give oxygen. Get medical attention.
Ingestion: Do not induce vomiting. If the material is swallowed, get medical
attention or advice.
Skin: If irritation is experienced, ush with water. If irritation persists, get
medical attention.
Eyes: Immediately ush eyes with water for at least 15 minutes while
holding eyelids open. If symptoms persist, get medical attention.
Section 5: FIRE FIGHTING MEASURES
Flash Point: (ethyl alcohol) 13°C
Auto-ignition Temperature: (ethyl alcohol) 363°C
Lower Explosion Limit: (ethyl alcohol) 3.3%
Upper Explosion Limit: (ethyl alcohol) 19.0%
Flammability Classication: Class IB Flammable Liquid
Suitable Extinguishing Media: Use methods appropriate for the
surrounding re. Consider water spray or fog, carbon dioxide, dry
chemical powder, or alcohol resistant foam.
Products of Combustion: Upon decomposition this product may
Safety Data Sheet
Distributed by EcoSmart Inc.
5870 W. Jefferson Blvd, Suite L, Los Angeles, CA 90016
P: +1 888 670 3674 F: +1 310 945 3339 www.e-nrg.com
Page 3
V072216
emit carbon dioxide, carbon monoxide, and/or low molecular weight
hydrocarbons.
Fire Fighting Equipment/Instructions: Wear protective clothing and
equipment suitable for the surrounding re, including helmet, facemask, and
self contained breathing apparatus.
HAZARD HMIS NFPA
Toxicity 2 2
Fire 3 3
Reactivity 0 0
Section 6: ACCIDENTAL RELEASE MEASURES
Personal Protection: For large spills wear gloves, Tyvek suits, safety glasses,
and appropriate NIOSH approved respiratory protection. Keep unnecessary
personnel away. Eliminate all sources of ignition or ammables that may
come into contact with a spill of this material.
Special Properties: Flammable Liquid! This material releases vapors at or
below ambient temperatures. When mixed with air in certain proportions
and exposed to an ignition source, its vapor can cause a ash re. Use
only with adequate ventilation. Vapors are heavier than air and may travel
long distances along the ground to an ignition source and ash back. A
vapor and air mixture can create an explosion hazard in conned spaces
such as sewers. If container is not properly cooled, it can rupture in the
heat of a re.
Environmental Precautions: Prevent discharge to open bodies of water,
municipal sewers, and watercourses.
Method for Containment: Absorb spilled liquid in suitable non-ammable inert
material such as clay, vermiculite or diatomaceous earth.
Methods for Clean-up: Ventilate area of leak or spill. Use spark-proof
tools to sweep or scrape up and containerize in approved chemical waste
container. Wash spill area with water.
Section 7: HANDLING AND STORAGE
Handling: Keep away from heat, sparks and ame. Use only with
adequate ventilation. To avoid re or explosion, dissipate static electricity
during transfer by grounding and bonding containers and equipment
before transferring material. Use explosion-proof electrical (ventilating,
lighting and material handling) equipment.
Storage: Keep container in a cool, well-ventilated area. Keep container
tightly closed and sealed until ready for use. Avoid all possible sources of
ignition (spark or ame).
Section 8: EXPOSURE CONTROLS/ PERSONAL PROTECTION
Engineering Controls: Provide exhaust ventilation or other engineering
controls to keep the airborne concentrations of vapors below their respective
threshold limit value. Ensure that eyewash stations and safety showers are
proximal to the work-station location.
Personal Protective Equipment (PPE)
Respiratory Protection: Vapor respirator. Be sure to use a MSHA/NIOSH
approved respirator or equivalent.
Wear appropriate respirator when ventilation is inadequate.
Eye/Face Protection: Safety glasses with side shields are
recommended as minimum protection in industrial settings.
Hand Protection: Butyl rubber gloves.
Body: Avoid skin contact. If product comes in contact with clothing,
immediately remove soaked clothing and shower.
Other Protective Equipment: Facilities storing or utilizing this material
should be equipped with eyewash and safety shower facilities.
See section 3 for exposure guidelines
Section 9: PHYSICAL AND CHEMICAL PROPERTIES
Appearance, State Clear liquid
Color Colorless
Odor Not available
pH (1%soln/water) Not Available
Vapor Density (Ethyl Alcohol) 1.6
Boiling Point (Ethyl Alcohol) 78.5°C
Vapor Pressure (Ethyl Alcohol) 57.3 hPa at 20°C
Melting Point (Ethyl Alcohol) -114.1°C
Freezing Point (Ethyl Alcohol) Not Available
Flash Point (See Section 5)
Flammability Properties (See section 5)
Solubility (in water) Soluble
Specic Gravity (Ethyl Alcohol) 0.78-0.8
Evaporation Rate Not Available
Octanol/Water partition
coefcient (Kow) (Ethyl Alcohol) -0.32
Auto-ignition temperature: (Ethyl Alcohol) 363°C
Decomposition temperature: Not Available
Section 10: STABILITY AND REACTIVITY
Stability: This material is considered stable at ambient temperatures 70ºC
(21ºC).
Condition to Avoid: Flames, sparks, electrostatic discharge, heat and
other ignition sources.
Incompatible Materials: This product reacts with strong acid, strong bases,
and oxidizing agents.
Hazardous Decomposition: Upon decomposition, this product evolves
carbon monoxide, carbon dioxide, and/or low weight hydrocarbons.
Hazardous Reactions: This product will not undergo polymerization.
Section 11: TOXICOLOGICAL INFORMATION
ACUTE EFFECTS:
Analysis LD50
Ethyl Alcohol (64-17-5)
Oral LD50 Rat: 7060 mg/kg
Isopropyl Alcohol (67-63-0)
Inhalation LC50 Rat: 72.6 mg/L/4H
Oral LD50 Rat: 4396 mg/kg
Dermal LD50 Rat: 12800 mg/kg
Dermal LD50 Rabbit: 12870 mg/kg
CHRONIC EFFECTS:
Ethyl Alcohol (64-17-5)
Carcinogenic Effects: A4 - Not classiable for human or animal by ACGIH.
Mutagenic Effects: Not Available.
Safety Data Sheet
Distributed by EcoSmart Inc.
5870 W. Jefferson Blvd, Suite L, Los Angeles, CA 90016
P: +1 888 670 3674 F: +1 310 945 3339 www.e-nrg.com
Page 4
V072216
Teratogenic Effects: Not Available.
Developmental Toxicity: Ethyl alcohol is a developmental toxin when
consumed during pregnancy.
Target Organs: When consumed, ethyl alcohol can target the respiratory
system, skin, eyes, CNS, liver, blood, and reproductive system.
Inhalation: May cause irritation to the mucous membranes of the upper
respiratory tract. Exposure over 1000 ppm may cause headache,
drowsiness, lassitude, loss of appetite, inability to concentrate, throat
irritation Ingestion: Can cause depression of Central Nervous System,
nausea, vomiting, diarrhea, intoxication, and in acute cases, death Eye:
Liquid and vapor may cause irritation. Splashes may cause temporary
pain and blurred vision.
Skin: May cause irritation, cracking, aking, and defatting of skin on
prolonged contact.
Chronic Exposure: Prolonged skin contact causes drying and cracking of skin.
May affect nervous system, liver, blood, reproductive system.
Isopropyl Alcohol (67-63-0)
Carcinogenicity: No known hazards
Mutagenicity: Not available.
Reproductive: Not available.
Developmental: Not available.
Target Organs: skin, eyes, CNS, and respiratory system.
Eye: Contact with eyes may cause redness and pain.
Skin: Contact with skin may cause dry skin.
Inhalation: Inhalation of this material may cause: cough, dizziness,
drowsiness, headache, sore throat, abdominal pain, labored breathing,
nausea, vomiting, and unconsciousness.
Ingestion: Ingestion of this material may cause: cough, dizziness,
drowsiness, headache, sore throat, abdominal pain, labored breathing,
nausea, vomiting, and unconsciousness.
Section 12: ECOLOGICAL INFORMATION
Ecotoxicity: Ethyl Alcohol (64-17-5)
96 hour LC50 Oncorhynchus mykiss: 12,900 mg/L (ow-through)
(30days old)
96 hour LC50 Pimephales promelas 14.2 mg/L
5 min EC50 Photobacterium phosphoreum: 35,470 mg/L
30 min EC50 Photobacterium phosphoreum: 34,634 mg/L
48 hour EC50 Daphnia magna: 9,268 mg/L
24 hour EC50 Daphnia magna: 10,800 mg/L
Ecotoxicity: Isopropyl Alcohol (67-63-0)
96 Hr EC50 Scenedesmus Subspicatus: >1000 mg/L
72 Hr EC50 Scenedesmus subspicatus:>1000 mg/L
96 Hr LC50 Pimephales promelas: 9640 mg/L [ow through]
96 Hr LC50 Pimephales promelas: 94900 mg/L [ow through] (29 days old)
96 Hr LC50 Pimephales promelas: 61200 mg/L [ow through] (31 days old)
5 min EC50 Photobacterium phosphoreum: 35390 mg/L
48 Hr EC50 Daphnia magna: 13299 mg/L
Section 13: DISPOSAL CONSIDERATIONS
Dispose of in accordance with local, state, and federal regulations.
Section 14: TRANSPORTATION INFORMATION
Proper Shipping Name: Flammable Liquids, n.o.s.
Hazard Class: 3
Identication No.: UN1993
Packing Group: II
Label: Flammable Liquid
Section 15: REGULATORY INFORMATION
TSCA Inventory This product and/or its components are listed on the Toxic
Substances Control Act (TSCA) inventory.
SARA 302/304 The Superfund Amendments and Reauthorization Act of
1986 (SARA) Title III requires facilities subject to Subparts 302 and 304
to submit emergency planning and notication information based on
Threshold Planning Quantities (TPQs) and Reportable Quantities (RQs) for
“Extremely Hazardous Substances” listed in 40 CFR 302.4 and 40 CFR
355. No components were identied.
CERCLA The Comprehensive Environmental Response, Compensation, and
Liability Act of 1980 (CERCLA) requires notication of the National Response
Center concerning release of quantities of “hazardous substances” equal to or
greater than the reportable quantities (RQ’s) listed in 40 CFR 302.4. As dened
by CERCLA, the term “hazardous substance” does not include petroleum,
including crude oil or any fraction thereof which is not otherwise specically
designated in 40 CFR 302.4. Chemical substances present in this product or
renery stream that may be subject to this statute are: No components were
identied.
SARA 311/312 Hazard The Superfund Amendments and Reauthorization
Act of 1986 (SARA) Title III requires facilities subject to this subpart to
submit aggregate information on chemicals by “Hazard Category” as
dened in 40 CFR 370.2. This material would be classied under the
following hazard categories: re, Acute (Immediate) Health Hazard,
Chronic (Delayed) Health Hazard.
Section 16: OTHER SUPPLEMENTAL INFORMATION
Prepared by: EcoSmart Inc. on June 3, 2014
Disclaimer: The information and recommendations contained in the Material
Safety Data Sheet (SDS) are supplied pursuant to 29 CFR 1910.1200 of the
Occupational Safety and Health Standards Hazard Communication Rule. The
information and recommendations set forth herein are presented in good faith
and believed to be correct as of this date hereof.
EcoSmart Inc, however, makes no representation as to the completeness
or accuracy thereof, and information is supplied upon the express condition
that the persons receiving the information will be required to make their own
determination as to its suitability for their purposes prior to use. In no event
will EcoSmart Inc be responsible for any damages of any nature whatsoever
resulting from the use of, reliance upon, or the misuse of this information. User
assumes all risk of use, storage and handling of the product in compliance
with applicable federal, state and local laws and regulations.
NO REPRESENTATIONS OR WARRANTIES, EITHER EXPRESSED
OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OF ANY OTHER NATURE, ARE MADE BY ECOSMART
INC HEREUNDER WITH RESPECT TO INFORMATION OR THE
PRODUCT TO WHICH THE INFORMATION REFERS. The information
as supplied herein is simply to be informative and intended solely to alert
the user of the substance which is the subject matter of this SDS. The
ultimate compliance with federal, state or local regulations concerning the
use of this compound, or compliance with respect to product liability, rests
solely upon the purchaser thereof.
This information relates to the material designated and may not be valid
for such material used in combination with any other materials nor in any
process.
Other manuals for BK Series
1
This manual suits for next models
13
Table of contents
Other EcoSmart Fire Indoor Fireplace manuals
EcoSmart Fire
EcoSmart Fire Linear 130 User manual
EcoSmart Fire
EcoSmart Fire Flex Series User manual
EcoSmart Fire
EcoSmart Fire Base User manual
EcoSmart Fire
EcoSmart Fire Ark 40 User manual
EcoSmart Fire
EcoSmart Fire ESF.1.F.650CV User manual
EcoSmart Fire
EcoSmart Fire Pillar Series User manual
EcoSmart Fire
EcoSmart Fire Ark 40 User manual
EcoSmart Fire
EcoSmart Fire Round 20 User manual
EcoSmart Fire
EcoSmart Fire 650DB User manual
EcoSmart Fire
EcoSmart Fire Lighthouse Series User manual
Popular Indoor Fireplace manuals by other brands
Pacific energy
Pacific energy BROADWAY Installation and operating instructions
Baxi
Baxi Gallery Series Installer's guide
Xaralyn
Xaralyn Serra manual
Montigo
Montigo H38-DF Installation & maintenance manual
Regency Fireplace Products
Regency Fireplace Products City Series Owners & installation manual
Quadra-Fire
Quadra-Fire Expression 36 owner's manual
Flamerite Fires
Flamerite Fires essence Voyager instructions
Monessen Hearth
Monessen Hearth DFX DBX24C Installation and operating instructions
Nordpeis
Nordpeis Capri Low installation manual
Valor
Valor H6 Series installation manual
Perel
Perel FH0005 user manual
VISION FUTURA
VISION FUTURA VF1300 Installation and user guide
Kovan
Kovan Eko line user manual
Celsi
Celsi B-1005975 instruction manual
Napoleon
Napoleon GVFS60-N Installation and operating instructions
Vermont Castings
Vermont Castings ExtremeView 33XDV brochure
Modern Flames
Modern Flames AMBIANCE LINEAR 40 Safety information and operations manual
Astria Fireplaces
Astria Fireplaces Brentwood LV manual