ECR 4 Kids ELR-008-B User manual

Use the Hex Tool
Trays (2)
Dry Erase Board (1)
Chalk Board (1)
Easel Legs (2)
Parts List
A
B
C
BEFORE ASSEMBLING, MAKE
SURE YOU HAVE ALL THE PARTS
Hex Screws & Plastic Nuts (8/8)
E1 E2
D
Batch ID Sticker
located on backside
E
Clips (4)
F
1Install the Dry Erase Board
Install the Chalk Board and Tray
2
Adjustable Art Easel
Model# ELR-008-B
Adult Assembly Required.
Two adults recommended.
- Contains small parts, sharp points and edges.
- Do not stand, sit, kneel, climb, lean or pull on
unit for support.
- Never leave children unattended.
- Do not place unit near high heat or moisture.
- Adult supervision recommended.
WARNING:
TOOLS INCLUDED
Hex Tool (1)
Open an Easel Leg (D) completely and secure the hinge into the locked position. Place onto a
protective surface with the locked hinge facing down.
Install the Dry Erase Board (B) onto Easel Leg (D) with two Hex Screws & Plastic Nuts (E1/E2)
as shown.
Open the other Easel Leg (D) completely and secure the hinge into the locked position.
Install the Chalk Board (A) onto both Easel Legs (D) with four Hex Screws & Plastic Nuts (E1/E2).
Align a Tray (C) behind the Chalk Board (A) before tightening the lower hex screws and plastic nuts.
Tip: Install the upper Hex Screws & Plastic Nuts first.
Reminder: Do not overtighten,
as the plastic threads can be
stripped.
Note: The height of the
board/tray can be adjusted by
installing into upper/lower sets
of holes on the Easel Legs.
Carefully rotate onto the
Dry Erase Board (B) on
a protective surface.
Reminder: Do not overtighten,
as the plastic threads can be
stripped.
Carefully rotate upright.
See Next Page
C
a
r
e
f
u
l
l
y
R
o
t
a
t
e
o
n
t
o
B
C
a
r
e
f
u
l
l
y
R
o
t
a
t
e
U
p
r
i
g
h
t
Batch ID Sticker
San Diego, CA 92110 USA
www.ecr4kids.com

Complete Dry Erase Board Installation
3
©2015 ECR4KIDS, LP Version: ELR-008-B_EP_2015.05.19
Care and Cleaning
Clean wood with a damp cloth or sponge
using warm water and mild soap. Wipe dry.
Do not place near heat, moisture or
vaporizer which may cause wood to warp
and peel.
Check for loose or worn parts periodically
and tighten or replace as necessary.
Record the manufacture date here.
Information is located on the Batch ID
sticker and on the shipping carton.
Save this sheet in an accessible place.
Model Number: ELR-008-B
Factory Code: EP
Manufacture Date:
Batch ID Number:
(Located on Part B)
Complete the installation of Dry Erase Board (B) onto left Easel Leg (D) with two Hex Screws
&Plastic Nuts (E1/E2).
Remove the lower Hex Screws & Plastic Nuts (E1/E2) on the Dry Erase Board (B). Align a
Tray (C) behind the Dry Erase Board (B) and re-install the lower Hex screws & Plastic nuts.
Reminder: Do not overtighten, as the plastic threads can be stripped.
Clip paper from the top edge of your Easel with the four Clips (F).
We appreciate your purchase of the Adjustable Art Easel.
ECR4KIDS has made every effort to supply a quality product that with proper
use and care, will provide many years of trouble-free use.
Warranty: Visit our website for product specific warranty information at:
www.ecr4kids.com
If you experience any difficulties with this product, please email us at
[email protected] or call toll-free at (855) ECR-4KIDS
(Monday - Friday, 7:00am - 4:00pm Pacific Standard Time)
Please do not return to place of purchase as ECR4KIDS will
replace defective part(s) and/or product.