Edgewater Networks EdgeMarc 4552 User manual

Page 1 of 7
EdgeMarc 4552
Networking Gateway
Quick Start Guide
Version 1.0
EWN00B-01-A001

Page 2 of 7
Before You Start
Please read this guide thoroughly as it describes the basic installation of
the device. Additional configuration needed to deploy the device in a
specific environment can be performed with the help of online help.
This guide also provides an example of a typical 4552 deployment that
can be used as a guideline for your installation.
Requirements for Installation
•A computer with a web browser such as Microsoft Internet Explorer or
Mozilla Firefox or any other browser of your choice
•At least one Ethernet cable
•Following information supplied by the Internet Service Provider:
oIP address of the WAN interface
oif T1 is being used for WAN connection then:
T1 frame format
Layer 2 protocol such as PPP, Frame Relay/DLCIs, HDLC,
etc.

Page 3 of 7
Instructions
Step 1 Connecting the Cables
1. Connect one end of an Ethernet cable to local LAN port 1 of the 4552. This port can be
seen in the area “B” of the above picture. Connect the other end of the cable to your
computer’s Ethernet port.
2. If T1 is used for the WAN connectivity then perform the following steps, otherwise go to
step 5.
3. Based on the number of functional ports, connect on end of the T1 cable(s) to the T1
port(s), located in area “D” of the above picture, and the other end of the cable(s) to the
T1 demarcation unit provided by the Service Provider.
To reduce the risk of fire, connect the T1 port to the T1 network using only 26
AWG or larger wire such as 24, 22, 20, etc.
4. Skip to step 6.
5. Connect an Ethernet cable between the Ethernet WAN port of the 4552, shown in the
above diagram as “C,” and the Ethernet port on a router or a modem.
6. Plug one end of the power adapter into an AC outlet and the other end into the power
receptacle on the 4552.
Make sure that the power and status LEDs, shown in the diagram below as “A” and “B”,
are solid green after a short while.

Page 4 of 7

Page 5 of 7
Step 2 Configuring the EdgeMarc
1. Launch a web browser on the PC and enter the following URL: http://192.168.1.1 and hit
enter.
2. The following login window should appear:
3. Enter “root” in the “User name” field and “default” in the “Password” field.
4. The “System” page should appear next. If you should see the "message of the day"
instead, just click on the System link under “Configuration Menu” to get to the “System”
page.
5. From the “Configuration Menu” on the left configure the following:
•“Network” – To configure WAN and LAN ports
•Optionally configure “DHCP Server” to suit your needs.

Page 6 of 7
Step 3 Plan Your Configuration
The EdgeMarc 4552 can be deployed as a gateway router in a network. It can also be deployed
in a network behind an existing firewall.
Note: When deploying VoIP services, all connected LAN switches or routers must support full
duplex.
Based on your deployment criteria, consult the following documents for further configuration:
•EdgeMarc 4552 Hardware Installation Guide
•VoIP Operating System (VOS) for EdgeMarc User Manual
Helpful Hints
Although not recommended, the 4552 and IP phones can be installed behind an existing
enterprise firewall. In this instance the firewall will have to be configured to allow access to and
from the 4552’s public IP address for the following ports:
Port Type Firewall Ports to Open
UDP 161 (SNMP) and 162 (SNMPTRAP)
RTP 16386 to 17286
TCP SSH TCP 22 for remote management & TCP 80 for WAN
configuration-downloads
Telnet 23
FTP TCP 21 for stateful TCP-session control from 4508T4W to
Edgewater FTP server
MGCP 2427, 2429, 2432, and 2727
NTP ¬123
SIP 5060 and 5075
IP phones normally point to a local NTP server for their time reference. The NTP port 123
needs to be opened if your network does not have an NTP server.
Please Note: Traffic shaping for this configuration is only available if the enterprise data
devices are also installed behind the 4552.

Page 7 of 7
The web page configurations for the various 4552 deployments are shown below. The two darker-
shaded rows indicate the minimum configuration required for each deployment.
4552
GUI Configuration
Page
4552 as
Gateway
Router
4552 within existing
infrastructure 4552 behind an existing firewall
Network Yes Yes Yes
VoIP/ALG Yes Yes Yes
NAT Yes Optional Yes
Firewall Yes Optional, but
recommended Optional, but recommended
DHCP Yes Yes (but should be
disabled if DHCP server
already exists)
Yes (but should be
disabled if DHCP server
already exists)
Traffic Shaper Yes Yes Optional (depends on
network topology)
Traffic Simulator Only for
testing Only for testing Only for testing
System As needed As needed As needed
Please visit our website at www.edgewaternetworks.com or contact the Edgewater Technical
Assistance Center at 408.351.7255 for additional information or assistance.
Edgewater Networks, Inc.
2895 Northwestern Parkway
Santa Clara, CA 95051
Phone: [phone]
[email protected]
Copyright© 2010, Edgewater Networks, Inc. All rights reserved.
Converged Networking. Simplified.