Edimax HP-5101 User manual

0


HP-5101
User Manual
08-2012 / v1.1




COPYRIGHT

Copyright©EdimaxTechnologyCo.,Ltd.allrightsreserved.Nopartofthis
publicationmaybereproduced,transmitted,transcribed,storedinaretrieval
system,ortranslatedintoanylanguageorcomputerlanguage,inanyformorby
anymeans,electronic,mechanical,magnetic,optical,chemical,manualor
otherwise,withoutthepriorwrittenpermissionfromEdimaxTechnologyCo.,
Ltd.
EdimaxTechnologyCo.,Ltd.makesnorepresentationsorwarranties,either
expressedorimplied,withrespecttothecontentshereofandspecifically
disclaimsanywarranties,merchantability,orfitnessforanyparticularpurpose.
Anysoftwaredescribedinthismanualissoldorlicensedasis.Shouldthe
programsprovedefectivefollowingtheirpurchase,thebuyer(andnotthis
company,itsdistributor,oritsdealer)assumestheentirecostofallnecessary
servicing,repair,andanyincidentalorconsequentialdamagesresultingfrom
anydefectinthesoftware.EdimaxTechnologyCo.,Ltd.reservestherightto
revisethispublicationandtomakechangesfromtimetotimeinthecontents
hereofwithouttheobligationtonotifyanypersonofsuchrevisionorchanges.
Theproductyouhavepurchasedandthesetupscreenmayappearslightly
differentfromthoseshowninthisQIG.Formoreinformationaboutthisproduct,
pleaserefertotheusermanualontheCD‐ROM.Thesoftwareandspecifications
aresubjecttochangewithoutnotice.Pleasevisitourwebsitewww.edimax.com
forupdates.Allbrandandproductnamesmentionedinthismanualare
trademarksand/orregisteredtrademarksoftheirrespectiveholders.


EdimaxTechnologyCo.,Ltd.
Add:No.3,Wu‐Chuan3rdRd.,Wu‐KuIndustrialPark,NewTaipeiCity,Taiwan
Tel:+886‐2‐77396888
Email:[email protected]

Contents
Chapter1:Introduction.....................................................................................................................................1
1.1ProductFeatures..................................................................................................................................1
1.2Application...........................................................................................................................................1
1.3Compatibility........................................................................................................................................2
1.4SystemRequirements..........................................................................................................................2
Chapter2:AbouttheProduct............................................................................................................................3
2.1LEDDefinitions.....................................................................................................................................3
2.2Interface...............................................................................................................................................4
Chapter3:GettingStarted.................................................................................................................................5
3.1HardwareInstallation..........................................................................................................................5
3.2CreatingaPowerlineNetwork.............................................................................................................6
3.3CreatinganEncryptedPowerlineNetworkwithTwoAdapters..........................................................7
Chapter4:UtilitySoftwareInstallation.............................................................................................................8
Chapter5:UsingtheUtilitySoftware..............................................................................................................14
5.1MainTab............................................................................................................................................14
5.2PrivacyTab.........................................................................................................................................17
5.3DiagnosticsTab..................................................................................................................................19
5.4AboutTab...........................................................................................................................................20
Chapter6:PowerlineNetworkManagementwithGroupButton..................................................................21
6.1FormingaHomePlugAVLogicalNetwork.........................................................................................21
6.2JoiningaNetwork..............................................................................................................................22
6.3LeavingaNetwork&JoininganotherNetwork.................................................................................23
Chapter7:Troubleshooting.............................................................................................................................24

1

Chapter1:Introduction

1.1ProductFeatures

zEasyplug‐n‐playsetupand128‐bitAESsecurity
zMax.powerlinespeedupto500Mbps
zBackwardcompatiblewith200Mbpspowerlineadapters
zFeaturesenergysavingmodetoreducepowerconsumption
zPowerlinetransmissionrangeupto300meters


1.2Application

zHigh‐definition(HD)andstandard‐definition(SD)videodistribution
zBroadbandInternetsharing
zInternetProtocolTelevision(IPTV)andVoiceoverInternetProtocol(VoIP)
applications




2

1.3Compatibility

200Mbps(EdimaxHP‐200xseries)and500Mbps(EdimaxHP‐500xseries)powerline
adaptersareabletocommunicatedirectlywithoneanother.200Mbpsand500Mbps
powerlineadapterscanbeusedonthesamehouseholdelectricwiringas14Mbps&
85Mbpspowerlineadapters(EdimaxHP‐85XXseries)withoutinterfering,butarenotable
tocommunicatedirectlywith14Mbpsand85Mbpspowerlineadapters.


1.4SystemRequirements

zComputerwithEthernetportrunningWindowsXP/Vista/7,Linux,MACOSXand
anyotheroperatingsystem.
zAnyconnecteddevicesmustfeatureanetworkport.
zUtilitysoftwaresupportsWindowsXP/Vista/7.


3

Chapter2:AbouttheProduct

2.1LEDDefinitions



LEDStatusDescription

LAN
GreenLANportconnected
BlinkingLANactivity(transferringdata)
Of
f
LANportnotconnected

PLC
Green/Red
Thegreenindicatorturnsonandtheredindicator
blinksslowlywhenthedeviceisdetectinga
powerlinelink.
Thegreenindicatorturnsonandtheredindicator
blinksquicklytoindicatedataisbeingtransferred
overthepowerlinelink.
Of
f
Noother PLC device detected

PWR
GreenPoweredon
Of
f
Poweredof
f

Note:Thedevicewillenterstandbymode,andallLEDswillextinguish,after
5secondswithoutanydatatransfer,includingwhentheEthernetcableis
disconnected.ThePowerLEDwillflashonceevery15seconds.




4

2.2Interface


InterfaceDescription
EthernetPortThisisaFastEthernetportforconnectingtoacomputeror
otherdeviceswithanetworkport.
Group/ResetCreatesanencryptedpowerlinenetworkgroupautomatically
(pressthebuttonforlessthan3seconds).
Leavesanencryptedpowerlinenetworkgroup
(pressthebuttonfor5~8seconds).
Restoresthepowerlineadaptertofactorydefaults(pressthe
buttonfor10~15 seconds).


5

Chapter3:GettingStarted

3.1HardwareInstallation

Alwaysplugthepowerlineadapterdirectlyintoapowersocket.Neverplugitintoa
multiplesocketoruninterruptiblepowersupply(UPS).



6

3.2CreatingaPowerlineNetwork

1. ConnectapowerlineadaptertoyourrouterviaEthernetcable,andthenplugitintoa
powersocket.



2. Connectanotherpowerlineadaptertoyourcomputer,andthenplugitintoapower
socket.

Note:Youcanalsoconnecttheadaptertoaprinter,settopbox,gamingconsole,TVor
otherdevicewithanetworkport,toaddthedeviceintothepowerlinenetwork.



3. MakesurethatthePLCandLANLEDslightuponbothPLCadapters.

4. Thecomputerandtherouterwillbeconnectedtothepowerlinenetworkautomatically.

7

3.3CreatinganEncryptedPowerlineNetworkwithTwoAdapters

Oncebothadaptershavebeensuccessfullyconnected,pressthe“Group/Reset”button
ofeachadapterforlessthan3secondswithin2minutes.Theadapterswill
automaticallygeneratearandompasswordtoencryptthepowerlinenetwork.



Note:
zToaddadditionaladaptersintotheencryptedpowerlinenetworkortoremove
anadapterfromthepowerlinenetwork,pleaserefertotheChapter6inthe
manual
zIfthepowerlineadapterinyournetworkdoesnotfeaturea“Group/Reset”or
an“Encrypt”button,youcanusetheutilitysoftwareasanalternative.For
moredetailspleaserefertoChapter5inthemanual.

8

Chapter4:UtilitySoftwareInstallation

Youcanmanagealltheconnectedpowerlineadapterswiththeutilitysoftware.Onlyinstall
theutilitysoftwarewhenyouneedtoaddotherpowerlineadapterswithout“Group”or
“Encrypt”button.

Step1Beforeinstallingtheutilitysoftware,makesurethatnootherpowerlineutilityis
installedonyourcomputer.Ifanyotherutilitysoftwareisinstalled,uninstallitand
rebootthecomputer.

Step2InserttheCDintoyourCD‐ROMdrive.Whenthefollowing“AutorunWizard”
appears,selectyourmodel.
Note:Ifautoplayisinstalledonyourcomputer,the“AutorunWizard”willstart
automatically.Otherwise,pleasegotoAutorunfolderintheCDandexecutethe
“AutoRun.exe”program.




9

Step3Thenclick“SetupUtility”.



Step4IfyouhavenotinstalledWinPcapversion4.1.2(orhigher)onyourcomputer
before,pleaseclick“OK”toinstalltheutility.Thewizardwillguideyouthroughthe
setupprocess.






10







11




Step5Whenthe“EdimaxPowerLineUtility”setupwizardappears,click“Next”to
continue.



12

Step6Inthe“LicenseAgreement”screen,pleaseselect“IAgree”andthenclick“Next”to
continue.



Step7Selectwhereyouwanttoinstalltheutilitysoftware,andthenclick“Next”.



13

Step8Ifyouconfirmtoinstalltheutility,click“Next”.



Step9Aftertheinstallationiscomplete,click“Close”.



Step10Aniconwillappearonyourdesktop.Doubleclicktheicontoopentheutility
software.



14

Chapter5:UsingtheUtilitySoftware

5.1MainTab

The“Main”tabprovidesalistoflocalorremotepowerlineadaptersinthenetwork.
Youcouldmanagetheremotepowerlineadapters(thoseonyourcircuit,butnotdirectly
connectedtoyourcomputer)here.



UpperPanel‐LocalDevice(s)onyourcomputer

Theupperpaneldisplayslocalpowerlineadaptersconnectedtothecomputer’s
networkport.Insituationswheretherearemorethanonelocaldevicebeingconnected,
suchasaUSBoranEthernetadapter,theusercanselectthelocaldevicebyclickingonit
andthenclickthe“Connect”button.Thestatusareaabovethebuttonindicatesthatyour
PCisconnectedtowhichdevice.Onceconnectedtothelocaldevice,theutilitywill
automaticallyscanthepowerlineperiodicallyforanyotherpowerlinedevices.Ifnolocal
powerlinedevicesarediscovered,thestatusareaabovetheconnectbuttonwillindicate
withamessage“HOMEPLUGADAPTERSNOTDETECTED’.


15

Ifyouwanttoupgradefirmwareoftheadapterdirectlyconnectedtoyourcomputer,
pleaseclick“Upgradefirmware”button.Thedialogboxwillbeshownasbelow,pleaseclick
“Browser”buttontochoosethePIBandfirmwarefilesyouwishtoupdateandthenclick
“OK”button.

Note:Pleasebesureyouhaveselectedthecorrectmodelfirmware,orthedevicemaybe
damaged.




LowerPanel‐PowerlineDevicesdetected

Thelowerpaneldisplaysremotepowerlineadaptersinthenetwork.Thefollowingare
descriptionsofeverysetupitems:

ItemDescriptions
DeviceNameThiscolumnshowsthedefaultdevicename,forexample:
“Device2”,“Device3”.Ifyouwanttochangethename,
pleaseclick“Rename”buttontoeditthename.
Password(DEKPassword)Thiscolumnbydefaultisblank.Inordertomanagethe
powerlineadapters,youhavetoenterthepassword(DEK
password)oftheadapter.TheDEKpasswordisprintedon
thelabellocatedinbackofthepowerlineadapter.After
youhaveenteredthecorrectpassword,thiscolumnwill
showthepassword.

Tosetthepasswordoftheadapter,firstselecttheadapter
byclickingonitsnameandthenclick“EnterPassword”
button.Adialogboxwillappearasbelow.Pleasetypethe
passwordandclick“OK”button.

16


QualityThestatusoftheconnectionqualitywillbeshownhere.
Rate(Mbps)Showsthecurrentdatarateofthepowerlineadapter.
MACAddressTheadapter’sMACaddresswillbeshownhere.
RenameSelectanadapterandclick“Rename”torenamethe
adapter.
EnterPasswordSelectanadapterandclick“EnterPassword”tosetthe
passwordfortheadapter.
AddThisbuttonisusedtoaddaremotepowerlineadapter
whichisnottheexistingnetwork.Clickthisbuttonandthe
followingdialogboxwillappear.Pleaseenterbothdevice
nameandthepasswordandclick“OK”button.
ScanClick“Scan”andtheutilitysoftwarewillperforman
immediatescanofotherpowerlineadapters.Bydefault,
theutilityautomaticallyscanseveryfewseconds.


17

5.2PrivacyTab

Inthe“Privacy”tab,youcancreateaprivatenetworkbychangingthedefaultnetwork
name.



Thefollowingaredescriptionsofeverysetupitems:

ItemDescriptions
PrivateNetworkNameAlmostallofthepowerlineadaptersshippedwiththesame
networkname“HomePlugAV”.Withthesamenetwork
name,allthepowerlineadapterscanbeconnected
directly.

Ifyouwanttocreateprivatenetwork,pleaseenterthenew
networknameandthenclick“SetLocalDeviceOnly”or
“SetAllDevices”button.
UseDefault(Public
Network)
Clickthisbuttonandtheinthe“PrivateNetworkName”
columnwillbeshownthedefaultname“HomePlugAV”.
SetLocalDeviceOnlyThisbuttonisusedtochangethenetworknameofthe
localdeviceonly.Onceyouhavechangedthenetwork
nameofthelocaladapteronly,theadaptersseenonthe
“Main”tabpriortothiswillbenolongerpresentinthe
network.
SetAllDevicesThisbuttonisusedtochangethenetworknameofall