Edimax Pan/Tilt IP Surveillance Camera IC-7000 User manual

I
IC C- -7 70 00 00 0
P
Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
Pan/Tilt Remote Control
with Audio & Night Vision
User’s Manual

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 2/62 Rev. PV1.0
--------------------------------------------TABLE OF CONTENTS--------------------------------------------
1. OVERVIEW.............................................................................................................................. 5
1.1 PRODUCT DESCRIPTION ............................................................................................................. 5
1.2 PRODUCT FEATURE .................................................................................................................... 5
1.3 PRODUCT SPECIFICATION ........................................................................................................... 5
1.4 PACKAGE CONTENTS.................................................................................................................. 6
1.5 SYSTEM REQUIREMENT .............................................................................................................. 6
1.6 INTRODUCTION OF IC-7000 EXTERIOR FUNCTIONS ...................................................................... 7
1.7 INTRODUCTION OF TV_OUT FUNCTION....................................................................................... 8
1.8 BASIC SET-UP PROCEDURES .................................................................................................... 9
2. UTILITIES AND TOOLS.............................................................................................................. 9
2.1 CAM_EZ SEARCH ..................................................................................................................... 9
2.2 USE IP-CAM AND TEST THE FUNCTIONALITY FOR THE FIRST TIME .............................................. 10
2.3 NETWORK SETUP ..................................................................................................................... 12
2.4 SETTING THE WAY HOW IP-CAM OBTAIN IP-ADDRESS............................................................... 12
2.5 INSTALLATION PROCEDURE FOR NETWORK ENVIRONMENT WITH RESIDENTIAL ROUTER ............... 25
2.6 WORK-AROUND FOR AUDIO PROBLEM WITH RESIDENTIAL ROUTER ............................................. 27
3. GETTING STARTED................................................................................................................ 29
3.1 SYSTEM LOGIN......................................................................................................................... 29
3.2 LIVEVIEW................................................................................................................................. 30
3.3 TAKE A SHOT............................................................................................................................ 33
4.ADVANCED FUNCTION OF LIVEVIEW ...................................................................................... 34
4.1 IMAGE ADJUSTMENT ................................................................................................................. 34
4.2 AVI RECORD SETUP................................................................................................................. 35
4.3 IMAGE ENLARGEMENT .............................................................................................................. 35
4.4 MOTION DETECTION SETUP ...................................................................................................... 36
4.5 MOTOR CONTROL .................................................................................................................... 37
5.ADVANCED APPLICATION ...................................................................................................... 37
5.1 IMAGE SETUP........................................................................................................................... 37
5.2 CAPTURE VIEW ........................................................................................................................ 38
5.3 EVENT TRIGGER....................................................................................................................... 39
5.4 NETWORK SETUP ..................................................................................................................... 40
5.5 SERVER SETUP........................................................................................................................ 42
5.6 ADMINISTRATION SETUP ........................................................................................................... 44
5.7 SOFTWARE UPDATE ................................................................................................................. 46

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 3/62 Rev. PV1.0
APPENDIX ................................................................................................................................49
APPENDIX A. USING A PPPOEDIALUP CONNECTION AND DDNS WITH THE IC-7000 EZ IPCAM (USING A
HUB ) ............................................................................................................................................... 49
APPENDIX B. FAQ: ........................................................................................................................... 58

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 4/62 Rev. PV1.0
Copyright©by Edimax Technology Co, LTD. all rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language or computer language, in any form or by any means,
electronic, mechanical, magnetic,optical, chemical, manual or otherwise, without the
prior written permission of this company
This company makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Any software described in this
manual is sold or licensed "as is". Should the programs prove defective following their
purchase, the buyer (and not this company, its distributor, or its dealer) assumes the
entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves the
right to revise this publication and to make changes from time to time in the contents
hereof without obligation to notify any person of such revision or changes.
The product you have purchased and the setup screen may appear slightly different
from those shown in this QIG. For more detailed information about this product, please
refer to the User's Manual on the CD-ROM.The software and specifications subject to
change without notice. Please visit our web site www.edimax.com.tw for the update. All
right reserved including all brand and product names mentioned in this manual are
trademarks and/or registeredtrademarks of their respective holders.
Linux Open Source Code
Certain Edimax products include software code developed by third parties,
including software code subject to the GNU General Public License ("GPL") or
GNU Lesser General Public License ("LGPL"). Please see the GNU
(www.gnu.org) and LPGL (www.gnu.org) Web sites to view the terms of each
license.
The GPL Code and LGPL Code used in Edimax products are distributed without
any warranty and are subject to the copyrights of their authors. For details, see
the GPL Code and LGPL Code licenses. You can download the firmware-files at
http://www.edimax.com.tw under "Download" page.
※ The product you have purchased and the setup screen may appear slightly
different from those shown in this QIG. For more detailed information about this
product, please refer to the User's Manual on the CD-ROM.
※ Software and specifications subject to change without notice. Please visit our web
site for the update.
※ All rights reserved. Trademarks or registered trademarks are the property of their
respective

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 5/62 Rev. PV1.0
1. OVERVIEW
1.1 PRODUCT DESCRIPTION
IC-7000 is an effective and easy-to-use IP Camera for remote monitoring. The setup
procedure required for this device is very simple. Built-in Web server allows you to use
web browser (e.g., Microsoft IE) through LAN or internet in any time and any place. Type
the IP address of the IP-CAM camera on the address bar of web browser to carry out the
works of remote image monitoring and administration. Also, the user can control the
motor of the camera to change the direction of camera over internet, and obtain the
real-time image of the monitored location.
In addition, the camera supports many network protocols such as PPPoE, DHCP,
STATIC IP, DDNS, SMTP, FTP and NTP with high-performance SDRAM control and
memory card access. The built-in TV-out decoding/coding feature can display monitored
image on TV screen (NTSC or PAL TV) in families with combining fast Motion Detection
and SD Expansion Card in hardware. Moreover, IC-7000 is equipped with IR LED, so it is
capable to work in environments without light. Besides, this device also has the function
of video recording and real-time photographing. To a family, such remote monitoring can
reach professional security and have great fun.
1.2 PRODUCT FEATURE
¾Use standard web browser to monitor, record, and take shot remotely.
¾Maximum image resolution: 640x480, full-screen display.
¾View images from multiple camera in a single web browser.
¾Allow on-line image viewing remotely for multi-user simultaneously
¾Motion-triggered capture.
¾Remote real-time video recoding, images can be stored on FTP, SD Card, PC, and send by
E-mail.
¾Support virtual IP and port switch in IP DSLAM.
¾Support multiple communication protocols: TCP/IP, DHCP, SMTP, FTP, PPPoE, DDNS,
¾Password-protected web access control.
¾Standard RJ-45 network connector, supports 10/100 Mbps Ethernet.
1.3 PRODUCT SPECIFICATION
Image Size: 160x120、320x240、640x480 (Selectable)
Image Quality: Fine、Normal、Basic (Selectable)
Video Frequency: 50 Hz for PAL、60 Hz for NTSC
Image Compression Format : M-JPEG
Focal Distance Range : From 30mm to infinity (Adjustable)
Digital Zoom : 4X
Video Recording : Video Frame rate setting : auto; 1, 3, 5, 10, fps (Selectable)
Motion-triggered image capture, image can be sent to FTP, E-Mail, SD Card and PC
Supports TCP/IP, SMTP, FTP, PPPoE, DHCP Protocol.

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 6/62 Rev. PV1.0
Obtain IP address from DHCP server, or manually setting. (Also supports PPPoE
protocol when used with DSL lines).
Build-in web server.
Remote image capture (JPG format), remote video recording (AVI format).
Microphone : High touch 10φ-40db±3
Video output frequency: 50 Hz for PAL、60 Hz for NTSC
Night vision: Auto and Manual (Selectable), IR LED x 6/ 5φ/850λ
Monitoring angle: Vertical angle: Up/Down Tilt +180 to –35 degrees
Horizontal angle: Left / Right Pan +/- 175 degrees
Standard RJ-45 network connector, support 10/100 Mbps Ethernet.
5V/ 1.5A switching power supply.
1.4 PACKAGE CONTENTS
1. IC-7000 Pan/Tilt IP-Camera
2. Power adaptor, 5V/ 1.5A power supply.
3. Ethernet Cable(red), used to connect to the network card of PC for testing purpose
and camera configuration.
4. Ethernet Cable (blue), used to connect to Hub, ADSL modem, residential router.
5. TV-OUT A/V Cable
6. Setup CD
7. User’s Guide (You’re reading now!)
8. Accessory for mounting camera.
1.5 SYSTEM REQUIREMENT
PC
Processor: Intel Pentium 4 ® 1.4GHz or above is recommended
RAM: 256MB or more.
Operation System: Windows 2000®or Windows XP®
Hard Disk: More than 10MB or more available disk spaces.
Network
Network Interface: 10/100/1000 Ethernet interface..

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 7/62 Rev. PV1.0
Web Browser: Microsoft Internet Explorer 6.0 or above
Internet connectivity.
Active-X plug-in.of IE.
1.6 INTRODUCTION OF IC-7000 EXTERIOR FUNCTIONS
Usage of Reset Switch:
In case the system is working abnormally, press and hold Reset Switch for a short period of
time (about 3 to 5 seconds) until Status LED is illuminated. The system will restart and the
device will recover to the factory default settings.
How to insert SD card:
Micro
p
hone
LED
(For status display)
IR LEDX6
Reset Switch
DC JACK
RJ-45 JACK
TV_OUT JACK
SD Card Slot
Focus ring
(For focus adjustment)

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 8/62 Rev. PV1.0
1.7 HOW TO CONNECT THE CAMERA TO TV SET
z1. Insert the TV_OUT cable to the TV-Out jack located at the back of camera, as shown in
Figure (1).
z2. Connect the power adapter to camera, as shown in Figure (2). Press and hold Reset
switch for three seconds. Then, release it. The camera will switch to TV_OUT mode.
z3.How to use TV_OUT function:
a. Hold to change TV output mode: Default TV-OUT mode is NTSC, if you want to use
PAL system, press and hold Reset switch about three seconds to
switch TV output mode between NTSC and PAL system.
b. Push to exit : Press Reset button to access into TV screen and adjustable
50Hz,60Hz,Outdoor
Reset Switch
TV_OUT
Cable
Adapter

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 9/62 Rev. PV1.0
1.8 PRODUCT SET-UP
2. UTILITIES AND TOOLS
2.1 CAM_EZ SEARCH
CAM_EZ Search is a camera search utility comes with this product. It can search all IP
CAMs connected to LAN by sending broadcasting packets. After IP CAM responds the
inquery packet, the utility will display a list of all IP CAM found on LAN. And it allows you
to modify the settings of specified IP CAM, such as IP address or the name of IP CAM.
CAM_EZ Search Screen
Anchor
Frame
Screw (P head
M3.5X25)

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 10/62 Rev. PV1.0
figure1
圖(一)
2.2 USE IP-CAM AND TEST THE FUNCTIONALITY FOR THE FIRST TIME
The following※network architecture is suitable for IP-CAM test/ IP address change
(static IP address) /firmware update (strongly recommended).
Please refer to the following instructions:
A. Installing the camera for the first time:
zYou computer must be equipped with network card and RJ-45 network
connector.
zConnect the RJ-45 jack which is located at the rear of IP-CAM with the red
test network cable. One end is connected to the network jack of computer;
the other end is connected to the network jack located at the rear side of the
IP-CAM.
zConnect the power adaptor to the power port (on the rear) of IP-CAM. Now,
the status LED on the top of IP-CAM will be illuminated.
Audio Port
number
(UDP)
Submit
settings
PPPoE Account
Choose the
way to get IP
IP address
Communication Port
Default Gateway
Subnet Mask
MAC address
Renew List
IP CAM List
IP CAM Name
Version of
CAM_EZ
Search
Version of IP CAM
Display the way
to
g
et IP
Renew
executed to
obtain an IP
Key in PPPoE

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 11/62 Rev. PV1.0
B. Make sure the IP addresses of PC and IP CAM are on the same network
section:
zUsually, static IP address will be used to access Internet, so the IP
address will vary. When you want to change IP address, please write
down the original IP address on your computer first. Then you have to
modify the IP address of your computer for testing if the IP-CAM can be
operated normally or not. After finishing the test, IP address for your
computer should be recovered to original settings.
zIn general, the IP address for your computer in LAN will be set with
“Obtain an IP address automatically”. To test the IP-CAM is working
properly or not, the IP address of your computer must be changed
temporarily. After the test is finished, it can be changed back to original
setting.
C. Next, choose Control Panel->Network Connections->choose the activated
area
Network Connections---> right click your mouse --->select Properties(P)--->
Select Internet Protocol (TCP/IP)---> Select Properties(R) , then you can
check the current IP address status for the computer. The way to modify IP
address is:
D. Open and execute CAM_EZ Search (as shown in Figure 2). The system will
scan the IP-CAM that you just installed automatically. Then, you will find
255IC-7000 in the column of Camera Lists. Click 255IC-7000 with left mouse
button. You can see the default settings of IP-CAM.
IPAddress(I):192.168.9.5
Subnet Mask (U):255.255.255.0
Default Gateway(D):192.168.9.254

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 12/62 Rev. PV1.0
Figure 2
2.3 NETWORK SETUP
Before you set up IP CAM, you have to know how your ISP provide you with IP address
(static or dynamic). If you do not know, please contact your ISP and ask for help.
Common network architecture (1 ~ 7 types).is listed in section 2.5, you can refer to the
listing to find out which type is suitable for your computer and finish the setting as the
instructions given in section 2.5. To set up IP-CAM and IP address, the common way that
people use is to change the obtaining of IP address of IP-CAM**. Detailed information is
listed in section 2.4-1 to 2.4.3.
2.4 SETTING THE WAY HOW IP-CAM OBTAIN IP ADDRESS
2.4-1 STATIC - IPAddress Setting
zYou computer must be equipped with network card and RJ-45 network jack.
zConnect the RJ-45 jack on the rear of IP-CAM with the red test network
cable. One end is connected to the network card of computer; the other end
is connected to the network jack located at the rear of the IP-CAM.
zConnect the power adaptor to the power jack (on the rear of IP-CAM). Now,
the status LED on the top of IP-CAM will be illuminated.
Step 1. Click Update. You can see 255IC-7000.
Step 2. Click 255IC-7000. You can see
Name : IC-7000
IP : 192.168.9.1
SubMask :255.255.255.0
GateWay :192.168.9.254
HTTP Port :Http communication port. The default
setting is 80.
AudioPort: Port used for audio transmission,
default setting is 1500.
Step 3. Make sure the IP setting is STATIC.
Step 4. Double click on 255IC-7000 to launch the
browser. Type ID/Password to login and get accessed to
network monitoring screen (for detailed information,
please refer to 3.1). If you can see the image displayed in
web browser, it means that IP-CAM is working properly.

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 13/62 Rev. PV1.0
zOpen and execute CAM_EZ Search (as shown in Figure 3). The system will
scan the IP-CAM that you just installed automatically. Then, you will find
255IC-7000 in the column of Camera Lists. Click 255IC-7000 with left
mouse button. You can see the default settings for IP-CAM.
Figure 3
zFill static IP Address as shown below. (If you do not know your IP address,
please contact your ISP. An example of static IP Address modification.is
shown below)
Step 4. Type Fixed IP.
Name :
IC-7000
IP : 211.78.174.94
SubMask ：255.255.255.248
GateWay ：211.78.174.89
HTTP Port：Http communication port. The
default setting is 80.
(If you have multiple IP-CAMs installed in the
same network, you have to divide them
with different Port numbers, e.g, 1025、
1026、1039…..)
UDP Port : UDP Port，Pre-setting is 1500
Step 5. Choose STATIC.
Step 6. After finishing the settings, click Submit. The
network settings for IC-7000 IP-CAM will be renewed.
Step 1. Click Update. You can see 255 IC-7000.
Step 2. Click 255 IC-7000. You can see
Name :
IC-7000
IP : 192.168.2.3
SubMask ：255.255.255.0
GateWay ：192.168.2.254
HTTP Port：Http communication port. The
default setting is 80.
(If you have multiple IP-CAMs installed in
the same network, you have to divide them with
different Port numbers, e.g, 1025、1026、1039….)
UDP Port : UDP port，Pre-setting is 1500
Step 3. Make sure the IP setting is STATIC.

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 14/62 Rev. PV1.0
Example:
1. Set up the IP CAM with static IP address.
2. Turn on your computer and launch IE browser. Type 211.78.174.94:( 1025、
1026、1039….) in the Address line. Now you can see the monitoring screen on
web browser.
2.4-2 DHCP - IPAddress Setting:
zUse RJ-45 Ethernet cable (red) to connect ADSL host and LAN hub. Then
use RJ-45 Ethernet cable (blue) to connect PC and IP CAM (as shown
below).
zConnect the power adaptor to the power port (on the rear) of IP-CAM. Now,
the status LED on the top of IP-CAM will be illuminated.
zSet up the connection way inside the PC network: Please go to

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 15/62 Rev. PV1.0
Control Panel ---> Network Connections ---> Choose Activated LAN
connection ---> right click your mouse ---> Select Properties(P)---> Select
Internet Protocol (TCP/IP)---> Select Properties(R)
--->Click Obtain an IP address automatically(O), Obtain DNS server address
automatically(B).
zStart CAM_EZ Search utility (as shown in Figure 3). Press Update to scan
the IP-CAM that you just installed automatically. Then, you will find
255IC-7000 in the column of Camera Lists. Click 255IC-7000 with left
mouse button. You can see the default settings for IP-CAM.
Obtain an IP address automatically (O)
Obtain DNS server address
automatically (B)
Step 1. Click Update. You can see 255 IC-7000.
Step 2. Click 255 IC-7000. You can see
Name :
IC-7000
IP : 192.168.2.3
SubMask ：255.255.255.0
GateWay ：192.168.2.254
HTTP Port：Http communication port. The
default setting is 80.
Step 3. Choose DHCP.
Step 4. After finishing the settings, click Submit. The
network settings for IP CAM IP-CAM will be
renewed. (That is, you can obtain a virtual IP
address)

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 16/62 Rev. PV1.0
Figure 5
Example:
1. Now, IP-CAM is set up with an IP address in LAN.
2. Or, use CAM_EZ Search to access the monitoring screen according to the
instructions given in Figure 5.
3. Or, turn on your PC and launch IE Browse. Type 10.1.10.82 in Address bar
to access the monitoring screen.
Step 5. Click Update. You can see 255IC-7000.
Step 6. Click 255IC-7000. You can see the change of
IP-CAM:
Name : IC-7000
IP : 10.1.10.82
SubMask ：255.255.0.0
GateWay ：10.1.10.252
HTTP Port：Http communication port. The
default setting is 80.
Step 7. The IP setting is DHCP.
Step 8. Double click 255IP CAM to open IE browser to
access into network monitoring screen.

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 17/62 Rev. PV1.0
2.4-3 PPPoE - IPAddress Setting
zAccess into monitoring screen of network by following the instruction given
in section 2.2.
zClick ‘Network’ on the left, please fill PPPoE account and password in
corresponding field, click ‘submit’ to save settings, and click ‘reboot’ to
restart web browser.
zStart CAM_EZ Search utility and click Update. Wait for 60 seconds (it varies
according to the connection quality). Then the system will search IC-7000
IP-CAM automatically. 1. Click the IP-CAM in the list. 2. Check the IP
address and Gateway. IP address obtained from ISP, SubMask and
Gateway will be shown in dimmed color. It means that IC-7000 IP-CAM
found is working properly with PPPoE.
1.
2.

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 18/62 Rev. PV1.0
zYou can also use CAM_EZ Search utility to setup PPPoE account and
password.
zSelect PPPoE. Click Submit to send out. The IC-7000 IP-CAM network
settings will be renewed.
zNow you can click the searched IP-CAM to open IE Browser to log onto
IP-CAM web configuration utility automatically.
INSTALL IP-CAM IN AN EXISTED NETWORK ENVIRONMENT
Scenario 1
The way to access Internet ADSL or Cable Modem
Public IP address required? Yes, several public IP addresses are required
for multiple IP-CAMs
DHCP server required? No
Network Setup for IP -CAM LAN Enable / Manually
This scenario is best for: Users with several static public IP addresses
and multiple IP-CAMs.
1. Connect the red test network cable to the RJ-45 Ethernet jack located on the rear
of IP-CAM. The other end is connected to the network card of computer.

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 19/62 Rev. PV1.0
2. Refer to 2.4-1 STATIC – IP Address Settings to input the IP address properly.
3. Set a static public IP address for each IP-CAM.
4. To view the image of IP-CAM from remote computer: Open IP browser and type in
the IP address of the IP-CAM, e.g., http://211.78.174.03.
Scenario 2
The way to access Internet ADSL or Cable Modem
Public IP address required? Yes, only one public IP address is required
DHCP server required? Yes
Network Setup for IP -CAM LAN Enable / Manually
Every IP-CAM need an unique port number
This scenario is best for: Users with one public fixed IP addresses,
residential router and several IP-CAMs
installed in local network.
1. Set a public IP address (e.g., 211.78.174.01) for the public IP of residential router.
Then, set the private IP address and activate the DHCP server function of residential
router.
2. In the IP configuration for each IP-CAM, please assign different private IP address.
In the Http Port setting, please give every IP CAM an unique port number. (Please

` IC-7000 CAM User’s Guide
P Pa an n/ /T Ti il lt t I IP P S Su ur rv ve ei il ll la an nc ce e C Ca am me er ra a
IC-7000 USER’S GUIDE PAGE 20/62 Rev. PV1.0
refer to 2.4-1 STATIC - IP Address Settings to get instructed.)
3. For the instruction of port mapping function of residential router, please refer to IP
and port settings of camera to make proper configuration.
4. To view the image of IP-CAM from remote computer: Launch IP browser and type
the public IP address of the residential router and the port number of IP-CAM, e.g.,
http:// 211.78.174.01:1025.
Scenario 3
The way to access Internet ADSL or Cable Modem
Public IP address required? Yes, a dynamically-located IP address is
required
DHCP server required? Must be equipped with DHCP and NAT
function
Network Setup for IP -CAM LAN Enable / Manually
Every IP-CAM need an unique port number
This scenario is best for: Users with dial-up ADSL, one dynamic IP
address and several IP-CAMs installed
1. Activate PPPoE function of residential router. Then, set private IP address and
activate the DHCP server function of residential router. When the dial-up procedure of
ADSL is completed, you will get a dynamically-allocated IP address from your ISP.
2. In the IP configuration for each IP-CAM, please assign an unique private IP address
for every IP CAM. For Http Port setting, please specify an unique port number for
each IP CAM also. (Please refer to 2.4-1 STATIC - IP Address Settings to get
instructed)
3. For the instruction of port mapping function of residential router, please refer to IP