Edmund Optics 86-885 User manual

86-885 MANUAL
Edmund Optics
Ver. 1.2

Contents
1. Cautions during Transportation and Installation ------------------------------------------------------------- P3
1.1 Cautions
1.2 Warning Label Positions and Descriptions
2. Specifications -------------------------------------------------------------------------------------------------------- P5
3. Preparation and Operation --------------------------------------------------------------------------------------- P8
3.1 Control Panel & Descriptions
3.2 How to Operate
3.3 Preparations before Use
4. Troubleshooting --------------------------------------------------------------------------------------------------- P9
5. Maintenance ------------------------------------------------------------------------------------------------------ P10
6. Dimensional Information -------------------------------------------------------------------------------------- P11
P2

1 Cautions during Transportation and Installation
1. This product is designed for indoor use, and should be installed on a flat
and vibration-free surface.
2. Avoid impacting the product all times. Stable power must be
supplied during operation.
1
Cautions1.1)
P3

Label Description
Electricity Warning –Avoid touching before
disconnection to power main
Do not open - Do not open door during
operation (The product automatically stops
when opened)
UV Light Hazard –Avoid looking directly at
light
1.2) Warning Label Positions and Descriptions
P4
①
UV Warning
②
③
④
Door Handle
PANEL
DISPLAY /KEY
PAD
INTER-LOCK

1 Specifications
2
P5
Item Description
Effective Area 5” in Diameter
UV Lamp Model No. KGW9n_UVA PL Lamp 9W x 4 EA
UV Lamp Lifetime 2,000 Hrs
UV Intensity 30mW/cm² at 365nm
Dimensions 13.3”(W)*10.6”(H)*11.3”(D)
Turntable Speed 6 RPM
Size 9.6” Glass Plate (effective area shown on plate)
Safety Feature All functions stop when door opens
Alarm Beeps for 5 sec after finish curing
Power 100~240 VAC 50/60Hz 1.5A Free Voltage (Selectable Switch)
Weight 10.0 kg

3.1) Control Panel & Descriptions
1 Preparations and Operation
3
P6
12345
No Function Key Description
①Display UV Curing Time / UV Lamp Lifetime
②START / STOP UV Lamp and Turntable ON/OFF
③+ Increases UV Curing Time (by 10 seconds)
④- Decreases UV Curing Time (by 10 seconds)
⑤MODE / RESET UV Lamp Lifetime & Zero Set

3.2) How to Operate
1 Preparations and Operation
3
P7
Item Operation
START /
STOP When pressed, lamp turns ON for designated time / When pressed again, lamp turns off (Only operational when door is closed)
+ Increases by 10 seconds per click / Increases rapidly when pressed for more
than 2 seconds (Max. 5 minutes)
- Decreases by 10 seconds per click / Decreases rapidly when pressed for more
than 2 seconds
MODE /
RESET
1) Shows accumulated time for lamp usage
2) Accumulated time is resettable when lamps are replaced by pressing button
for more than 2 seconds –When accumulated time reaches 2,000 hrs,
display keeps blinking until reset
Err Lamps off / All functions stop when door gets opened

3.3) Preparations before Use
1 Preparations and Operation
3
①Select correct voltage depending on location.
②Connect appropriate power cable into power input port, and connect power.
③Turn on power.
P8
No Item Description
①Power Select Select Power 100 V / 220 V
②INPUT AC VAC 3P Cord Plug
③FUSE 3A Fuse Holder
④POWER Power ON/OFF Switch
1
2
3
4

1 Troubleshooting
4
P9
Regular check-up is necessary.
If problem persists, please contact supplier or manufacturer.
Item
Unit
Problem
Possible Cause
Solution
UV Lamp
-
Malfunctioning
UV
Housing
No Light /
Low in Intensity
1. Lamp is not
properly connected.
2. Lamp is used for
too long
1. Check connection
between lamp
and socket
2. Replace lamp
Keypad
–
No Response
Keypad
No Response /
Malfunctioning
1. Damage on board
2. Damage on power
supply
1. Replace board
2. Check power
supply (Check
fuse)
How to Check Fuse
1) Open Fuse Holder located at the back of product, and check for disconnection of fuse.

1 Maintenance
1. Intensity of UV Lamp decreases slowly after it gets used for a certain
period of time.
2. When the accumulated usage time for lamp gets close to 2,000 hrs prepare
replacement lamps.
5
Decrease in Intensity of UV Lamp
P10
5.1)

1 Dimensional Information
6
P11
- UV System Dimensions