EDS ES Series User manual

ES Series
WARNING SYSTEMS
VOICE ANNOUNCEMENT
Installation Manual
www.eds.com.tr

2
It is designed to provide pointemergency announcements for visually-impaired
people. The system consists of an audible and flashing announcement
module and a wireless alert button.
The storage for sound recording have been divided into four sections each
of them is 20 seconds long, 80 seconds in total. Four different scenarios
could be chosen for recording messages (evacuation, routing to another area,
regional re risk, forbidden zone). Audio les on computers, tablets and similar
devices can be directly transferred to the device through direct connection to
the device. The voice announcement module delivers announce at selected
time intervals by pressing the wireless alert frequencies, when activated by
pressing the wireless alert button. The duration of the announcement can be
selected as 30, 60, 90, 120 minutes.
Product Family
DESCRIPTION
1
P/N Description
ES12 Audio Alert Device for Visually-Impaired People (12V)
ES24 Audio Alert Device for Visually-Impaired People (24V)
EKB Wireless Alert Button

3
ES12 / ES24 Audio Alert Device
EKB Wireless Alert Button
PHYSICAL
2
86 39
86
235 90
240

4
SPECIFICATIONS
3
Model ES12 ES24
Environment class IV Outdoor
Electrical
Operating voltage 160-265V AC
Input voltage 12V DC 24V DC
Flasher White
Speaker/Speaker Protection 8ohm/Available
Sound power/Sound power level 20W/Adjustable 75W/Adjustable
Harmonic distortion <%0,1
Amplier efciency >%93
Watchdog protection Available
Detector connection - ECP2L Optical Smoke Detector
Fire alarm button connection - ECB20R Fire Button
External module support Wireless Alert Button (EKB)
Speaker Connection Optional
Announcement Selectable announcement time
Announcement stop With reset button or wireless re button
Trigger input 12V DC or dry contact 24V DC or dry contact
Communication frequency 868Mhz @ Dual communication is available

5
Battery unit
Battery 12V/1.2Ah 2 x 12V/1.2Ah
Battery charging time Max. 72 hours, full charge capacity
Fixed discharge time is higher than nominal capacity.
24 hour charge Nominal ampere hour >%80
Battery charging current It must be charged at a current > c/10.
Corrosion fault Alert information is available on the device (max 4 hours).
Device charge capacity The device can be powered by 220V and can charge public
address system and battery separately.
Deep discharge protection Available
Battery voltage warning Warning LED before deep discharge
Battery run-time after power loss Max. 72 hours
Battery replacement Install and operate
Warnings and indicators
LED indicator
Green Device is active, device is powered by battery or mains
Yellow System failure, re zone open and short-circuited
Warning against open circuit, short circuit and corrosion
Flasher Compatible with EN 54-23
Flasher housing Policarbonate
General
Enclosure / Color / Type ABS Plastic / White / Standard
Protection class IP44
Operating temperature 0OC / +45OC
Dimensions (HxWxD) / Weight 240x235x90mm / 1700g 240x235x90mm / 2250g

6
Model EKB
Type Wireless Alert Button
Electrical
Operating voltage 3V DC
Communication frequency 868Mhz @ dual communication
Resetting With special reset switch without disassembling
Battery / Battery reverse protection Li-ion battery (CR17345) / Available
LED indicator Battery low, data communication status
General
Housing / Color / Type ABS Plastic / Red / Standard
Button glass Shatterproof glass
Protection class IP24
Operating temperature -10OC / +55OC
Dimensions (HxWxD) / Weight 86x86x39mm / 97g
Year of manufacture The year and week of manufacture is included in the rst four
digit of your product serial number (located on the product
identication label)
Manufacturer EDS Elektronik Destek Sanayi ve Ticaret Ltd.
Meclis Mah. Teraziler Cad. Hayran Sk. No: 4 34785
Sancaktepe / Istanbul / TURKEY
Recycle

7
1
2
3
4
5
LED 1 Green Power LED
LED 2 Green (BATTERY) Permanent: Supplying from battery.
Flashing. Battery s being charged.
LED 3 Red (ALARM) Alarm existing in wired or wireless zone.
LED 4 Orange (ZONE ERROR) Permanent: Zone open circuit.
Flashing: Zone short circuit. Wireless zone error
or EKB cell low.
LED 5 Orange (BATTERY ERROR) Permanent: Battery absent or low.
Flashing: Oxidation.
Figure 1: Front Panel
Audio Alert Device
CONNECTIONS
4
2
1345

The connector is xed to socket input on the lower
part of the card as shown in Figure 2.
The screw holes on LED card are placed
corresponding to screw holes on the part with
number (1) as shown in the picture and they are
screwed down with 3x6 metric screws.
Four different sound records can be
announced in our product. The recorded
sounds are as follows:
Record 1: It activates in case of giving
alarm from (11) entry connected
alarm button or smoke detectors.
The announcement of “Use other
emergency exits for evacuation”.
(Figure:3)
Record 2: The announcement of
“Emergency Exit is Here” in case of
giving alarm from trigger entry (12) . 8
LED card mounting;
Recorded Sounds and New Sound
Recording
1
PROGRAMMING
5
Figure 2: LED Card Mounting
Figure 3: Motherboard
8
9
6
7
11
10
2
1
13
15
14

Record 3: The announcement of “Emergency Exit is Here” in case of giving
alarm from wireless button.
Record 4: Reserved for wireless contact. It will include announcement
regarding unnecessary disuse of emergency exits.
Record 1 is privileged from other announcements. While other announcements
are made and if the condition develops stated for record 1, then other
announcements are silenced and the record 1 announcement is started.
The address to be recorded from the jumpers
marked with (9) is selected in Figure 3.
Address 1 (30)
Address 2 (60)
Address 3 (90)
Address 4 (120)
9
If New Sound Recording Requested to the
Required Address:
Figure 4: Announcement time selection
Figure 5: Sound connector
The sound connector of the recording device is
installed to the point bookmarked with (6).
The ‘AUX ON li position is selected from the
jumper marked with (14). If you want to use
the built-in microphone for recording, the ‘MIC
ON isten position is selected.microphone for
recording.
9
9
15

10
Figure 6: Jumper
bookmarked with (8)
Figure 7: Trigger settings jumper
The jumper bookmarked with (8) should be normally
in installed state. When this jumper is removed,
record begins and red LED flashes. When the
record is when the record is completed, LED goes
out and the recorded sound is announced. (Figure:3)
The jumper bookmarked with (8) is installed to its
place and the reset button is pressed. The flashing
of the Flash LED is seen for once. The recording
operation is completed, repeat the same operation by
selecting address from the jumper bookmarked with
(9) for new record.
Selection of the Announcement Time
The announcement time is selected from the jumpers bookmarked with (9) in
Figure 4. It has been bookmarked as (30), (60), (90), (120) minutes.
Trigger Settings
If Jumper (7) is plugged KL2 should be short circuit
in normal conditions; if it is not plugged then an-
nouncement starts at open circuit condition.
8
7
2
1