EDS SD630A User manual

SD630A AK, SD630A24 AK24//
INSTALLATION MANUAL
TELEPHONE DIALLER
412
TELEPHONE DIALLER
SD630A AK, SD630A24 AK24//
KK-SD630/110907_ER3
f:/pazarlama/kullanýmkýlavuzlarý/eds/english/sd630_ER3
How to Delete a Pre-entered Telephone Number
Engineering code
MMMM#01#
MMMM#02#
MMMM#03#.
MMMM#04#
MMMM#05#
MMMM#06#
MMMM:
For deleting 1. Telephone number:
For deleting 2. Telephone number:
For deleting 3. Telephone number:
For deleting 4. Telephone number:
For deleting 5. Telephone number:
For deleting 6. Telephone number:
(default 1234 )
After entering the 4-digit engineering code, #, row number and user code
if you enter a valid syntax you hear, two beeps. If you enter an invalid syntax you hear single beep. That means wrong
operation has been done, and the commands are ignored. You could repeat the operation by pressing # button.
1234#01#
please enter the followings in order:
Example:
When the device receives an alarm it starts calling the pre-entered telephone numbers from the first number. It can call
5 times if the dialed number doesn't answer or it is busy. After 10 times ringing if it's not answered it calls the next
number. The device reads 16 seconds recorded voice.
After reading the message, the device waits 10 seconds to have an order. After listening the message enter the user
code than press the 2 button and if you heard two beeps it cannot call the following telephone number, the relay is
became an active conditions by entering user code than pressing 1 button in 10 seconds.
To make another operation 2-3 seconds should be wait. (The relay in active conditions.)
The device reads 16 seconds recorded voice:
NOTE:
How the device operates
How to Enter Passwords
After entering the 4-digit engineering code, #, row number and user code
if you enter a valid syntax you hear, two beeps. If you enter an invalid syntax you hear single beep which means
wrong operation. You can repeat the operation by pressing # button.
please enter the followings in order:
MMMM:
SxSxSx:
Example:
Engineering code (default 1234 )
New password
1234 # 07 5612 if you want to set 5612 user password
Setting 1. Telephone's number's password: MMMM # 07 S1S1S1
Setting 2. Telephone's number's password. MMMM # 08 S2S2S2
Setting 3. Telephone's number's password: MMMM # 09 S3S3S3
Setting 4. Telephone's number's password: MMMM # 10 S4S4S4
Setting 5. Telephone's number's password: MMMM # 11 S5S5S5
Setting 6. Telephone's number's password: MMMM # 12 S6S6S6
Changing the engineering code: MMMM #13 S7S7

General Specifications
Technical Specifications
TELEPHONE DIALLER
•
•
•
•
•
•
•
If the dialed numbers do not answer, can call 5 times
16 seconds voice message recording time
Recorded messages and telephone numbers are not erased in case of power failure
Special password for each number
Receives the lines and calls incase of alert even if the line is busy
Relay can be controlled by special password
Microprocessor controlled
2434
SD 630A is a security dialer which calls up to six telephone numbers and playbacks pre-recorded voice as a warning
message, when an alarm occurs. The alarm is detected when the alarm terminal of the device are open-circuited. In
normal operation alarm terminals should be short-circuited and jumpers should be positioned as shownin figure 3
and jumpers must be positioned as shown in Figure 3 and a phone line is connected to LINE terminal of the device.
J1 and J2 should be in N (Normal) position while in normal working mode, as shown in Figure 3. Operates with
Negative Triggering When the Jumper 5 as in Figure 1, and operates with Positive Triggering when the jumper as in
Figure 2.
Max Voice Recording Time
Calling Time
Power Supply
Power Consumption
Box Type
Box Dimension
Model SD630A SD630AK
TELEPHONE DIALLER
16 sn.
70sec (Tone)-80sn. (Pulse)
12VDC 24V DC
Max.50mA(sleep mode) max.100mA(active mode)
ABS plastic Card type ABS plastic
12x15.7x3.2 90x80x25 12x15.7x3.2
General Issues
Parameters and Programming Methods
NOTE 1:
NOTE 2:
NOTE 3:
NOTE 4:
NOTE 5:
NOTE 6:
We can start to operate SD 630A 3 seconds after supplying power.
Siren sound is heard on the telephone on alarm conditions.
The alarm output of the alarm panel should be dry contact type.
Fabrication engineering code is 1234.
To return to the fabrication codes, please, first cut off the power, short circuit J4 then apply the power. You
will hear the confirmation sound then you should make J4 open-circuit.
Operating frequency is between 390Hz and 490Hz
SD630A24 SD630AK24
POZ
NEG
POZ
NEG
J5
Figure 1
PN
J2
Figure 3Figure 2
PN
J1
J1J2
J3
J5
J4
(Jumper Positions for programming Mode)
How to Program the Device
The device should be programmed before using it. During programming J1 and J2 jumpers conditions should be
as in figure 4. 6 telephone numbers can be programmed and each telephone number can have special password
Voice Recording and Playback
To Record Voice :
To Playback:
J1 and J2 must be programming conditions . Hang up the telephone which is connected to
the TEL port of the device and short-circuit J3 jumper when the red led on the PCB is on device start recording your
warning message. The message should not exceed 16 seconds. When the LED light is off that means the recording time
is over. When the recording is finished J3 jumper must be open-circuited again.
J1 and J2 must be programming conditions (Figure 4). By pressing MMMM # 14 buttons. You could listen
the pre-recorded message. To pass different operation you must wait 16 seconds. The device can not make telephone call
if the warning message wasn't recorded.
(Figure 4 )
Tone, Pulse Selection
At default, the dialer is in tone mode; by pressing it would be converted to the pulse mode.MMMM #15
SD630A AK, SD630A24 AK24// SD630A AK, SD630A24 AK24//
MMMM:
Example:
Engineering code (default 1234 )
1234 # 01 0532 9876543# (If you want to enter 0532 9876543)
TEL
(Programmer)
LINE
(Telephone
Line)
ALRM
(Trigger)
COM NC
(Relay Output)
NO +12V-
(Power supply)
PCB CARD
'
(to program the
device you need)
Important:
telephone line must be direct,
please don’t connect PABX devices.
N.C
Trigger Button
(to make the device call)
12V
Power Supply
. Telephone number: MMMM #04 Tel4 #
Telephone number: MMMM #05 Tel5 #
Telephone number: MMMM #06 Tel6 #
Setting 4
Setting 5.
Setting 6.
Setting 1.
Setting 2.
Setting 3.
Telephone number: MMMM #01 Tel1 #
Telephone number: MMMM #02 Tel2 #
Telephone number: MMMM #03 Tel3 #
J2 J1
P
P
N
N
Figure 4 P
P
N
N
NOTE: After entering, 4-digit engineering code, #, row number, telephone
number and #, if you enter a valid syntax you hear, two beeps. If you anter an invalid syntax you hear single beep
which means wrong operation. You can repeat the operation by pressing # button.
please enter the followings in order: