EF CK-ISLAND FORD User manual

CONTENT
ISLAND HOOD CK-ISLAND
FORD
THE BEAUTY OF SIMPLICITY
USER MANUAL

1……………………………………….Notice
2……………………………………….Feature
3………………………………………..Installation
4………………………………………..Notice of installation
5………………………………………..Safety Warning
6…………………………………………Use
7…………………………………………Maintenance
8…………………………………………Abnormity and Solution
9…………………………………………..Warranty card
NOTICE

1. Thank you for choosing our cooker hood. Please read
the instruction manual carefully before use.
2. The installation work must be undertaken by a qualified
and competent fitter.
3. The manufacturer disclaims all liability for any damage or
injury caused as a result of not following instructions for
installation contained in the following text.
The cooker hood is used on 220-240V, 50Hz.
FEATURE
1. The cooker hood uses high quality materials, and is made
with a streamlined design.

2. Equipped with a large power low
noise electric motor and centrifugal leaf, it
produces strong suction, low noise, non
stick grease filter and easy to clean.
3. With the isolated low voltage circuit
board control, 12vAC input, the lights are
therefore safer.
4. Special wind tunnel construction and
oil collector design, free dirt will be
absorbed in a second.
Installation
1. The ceiling must can bear at least 120kgs weight, and the
thickness of the ceiling must be ≧30MM, drill 1*170mm
round hole in the ceiling.

2. According to the hanging board, drill 12 holes in the
ceiling, see pic 2, 12pcs
of ST6*40mm big
flat screws will be
used to fix the hanging
board on the ceiling,
and then 8pcs of
M4*10 screws and M4
nut with gasket will be used to connect the angle iron into
the hanging board, see pic 1, calculated the length of the
angle iron, and 16pcs M4*10 big flat screws and M4 nut
with gasket will be used to connect the angle iron and
another angle iron ( the overlap length of angle iron can
not less 100MM)
3. Let the one side of the extensible pipe go outside through
the hole of 170MM, see pic 3.
4. 4pcs ST4*8 big flat screws will be used to connect the
internal chimney into the hanging board, then put one the
external chimney, two hooks will be used to put up the
external chimney in order to the next installation, see pic
4.
5. 4pcs ST4*8 big flat screws will be used to install the
outlet, see pic 5.

Pic 5
6. Hold up the hood, 16pcs M4*10 big flat screws will be
used to connect the hood body into angle iron, see pic 6.
7. Put the extensible pipe on the outlet; after ensure all the
things ok, put down the hook, take from the external
chimney, all the installation is finished, see pic7& 8.
Pic 6 Pic 7 Pic 8
NOTICE OF INSTALLATION
1. Before installation, please ensure the area is clean to
avoid suction of the remaining bits of broken wood and
dust.

2. It cannot share the same air ventilation tube with other
appliance such as gas tube, warmer tube, and hot wind
tube.
3. The bending of ventilation tube should be≤120°, parallel
or above the start point and should be connected to the
external wall.
4. After installation, make sure that the extractor is level to
avoid grease collection at one end.
SAFETY WARNING
•
••
•Never let the children operate the machine
•
••
•The cooker hood is for home use only, not suitable for
barbecue, Roast shop and other commercial purpose.
•
••
•Please ask the technical person to do the assembling.
•
••
•The cooker hood and its filter mesh should be clean
regularly in order to keep in good working order.
•
••
•Before cleaning, please switch the power off at the main
supply.
•
••
•Clean the cooker hood according to the instruction
manual and keep the cooker hood from the danger of
burning.
•
••
•If there is any fault with the appliance, please call the
service department to arrange a service engineer.
Speed adjustment .See pictures
LCD Electronic button

Pic 10
1. Plug the hood; LCD will display 24-hour system with blue
backlight. Backlight will be extinguished after 30 seconds
without any operation.
2. Press “ ” button once; lights will be on and LCD will show
“ ”. Press “ ” button again; lights will be off and “ ” on
LCD will disappear.
3. Press “ ” button once; the hood works at LOW speed and
LCD will show “ ” and “ ” button will be on. Press “ ”
button again; the hood works at MEDIUM speed. Press
“ ” button one more time; the hood works at HIGH speed.
Press “ ” button again; the hood works at LOW speed
again and it repeat. While pressing “ ” button; the “ ”
button is always on. If you want to stop the hood now; press
the “ ” button once.
4. When the hood is not working; press “ ” button once. The
hood will work at the speed it works last time and LCD will
show “ ”. Press “ ” button again; the hood stop working
and “ ” will disappear from LCD.
5. When both “ ” button and “ ” button don’t work; “ ”
button is used for time-setting. Press “ ” button for 2 to 3
seconds; will be shown on LCD and flashes;
which represents hour. Press “ ” button once the number
adds by 01. Continue pressing “ ” button; it will display

from 13;14… until 23. When LCD shows 23; it doesn’t work
by pressing “ ” button. Press “ ” button once; the
number reduces by 01. When LCD shows 00; it doesn’t
work by pressing “ ” button. After setting hour; you can
start setting minute by pressing “ ” button again. on
LCD flashes; which represents minutes. Press “ ” button
once the number adds by 01. Continue pressing “ ”
button; it will display from 01;02… until 59. When LCD
shows 59; it doesn’t work by pressing “ ” button. Press
“ ” button once; the number reduces by 01. When LCD
shows 00; it doesn’t work by pressing “ ” button. After
setting hour and minute; press “ ” to confirm.
When “ ” button doesn’t work; “ ” button is used for delay
timer function. Delay timer function allows you to set the
hoods automatically power off according to the delay timer you
set from 1 minute to 60 minutes. Press “ ” button once; it
enters for delay timer setting and LCD shows . Press
“ ” button once the number adds by 01. Continue pressing
“ ” button; it will display from ; ;
… until Press “ ” button once; the
number reduces by 01. After setting delay timer you want;
press “ ” button to confirm. If you set delay timer as 05:00;
the LCD display will show from 05:00; 04:59… until 00:01
00:00. When LCD shows 00:00; the hood will automatically
power off and LCD display will only show 24-hour system with
blue backlight. After 30 seconds without operation; blue
backlight will disappear. But please note the Lamp is not
under control of delay timer. Next time; if you want to use
delay timer function and you press “ ” button without any
change on time. The hood will automatically count time down
from your previous setting after 5 seconds.

MAINTENANCE
The cleaning of the carbon grease filter mesh
The filter mesh is made of high-density stainless steel. Please
do not use the corrosive detergent on it. Keeping this filter
clean will keep the appliance running correctly. Please strictly
follow the guidelines below.
Method 1: Put the mesh into 40-50 c clean water, pour on
detergent, and soak for 2-3 mins. Wear gloves and clean with
a soft brush. Please do not apply too much pressure, as the
mesh is delicate and will damage easy.
Method 2: If instructed to do so, it can be put into a
dishwasher, set the temperature at around 60 degrees.
Notice of cleaning cooker hood
A. To protect the main body from corrosion over a long
period of time, the
cooker hood should
be cleaned
with hot water plus
non corrosive
detergent
every two months.
B. Please do not use
abrasive
detergent
for it will damage the
body.

C. Keep the motor and other spare parts free from water,
as this will cause damage to the appliance.
D. Before cleaning the appliance please remember to cut
off power
E. The carbon filter shouldn’t be exposed to heat.
F. Please don’t tear open the fixed bar around the carbon
filter
G. If the plug or cord is damaged, please replace it with
special soft cord.